Use these caps to hold components in place and protect shaft ends.

Also known as X-washers, place these rings into the groove and squeeze tight with pliers to form a 360° closure.

A coil makes a stronger grip than standard hairpin cotter pins to prevent accidental release.

These pins are coiled for more tension than standard wire-snap cotter pins.

Slide the pin through a hole then snap the ring down to lock these pins in place. Also known as click pins.

Also known as key rings, twist these rings into place to secure clevis pins, connect components, or add a pull handle. They don't have the sharp ends of other cotter pins.

The double-head design lets you push or pull these pins from either side of the hole. Once in place there's little chance they will be vibrated out or knocked off.

Spring force holds pieces of telescoping tubing together. Also known as snap buttons and tubing buttons.

The low-profile head on these pins holds them in place on one side.

A large loop handle makes these pins easy to grip.

The bend makes these pins easy to insert and pull out.

A plastic-coated T-handle welded to these pins makes them easy to grab.

Use these light-duty clip-on nuts in low-clearance applications.

The S-style design provides more strength than other no-slip clip-on nuts.

Slide these nuts on the edge of a panel and position them by hand. Also known as G-style clip-on nuts.

With flexible teeth that slide smoothly over threads of any pitch, these push nuts can be used alone for light-duty applications or as a jam nut.

A flange distributes the load over a large area and reduces stress where the nut meets the material surface.

Attach these slip-on nuts at any point on a threaded rod for quick installation.

Hex speed nuts can be gripped with a wrench for ease of removal.

These rounded head nuts can be riveted into thin panels for a flush fit. They can be mounted without spaces between the panels. A quarter-turn locks and releases access panels, doors, and covers.

These wing-head screws have a clip-on nut that allows you to mount them near the edge of a thin panel. Use them to lock and release access panels, doors, and covers with a quarter-turn.

Press these rounded head nuts into a closed-end hole or thick panel in applications where the back of the panel is inaccessible. A quarter-turn locks and releases access panels, doors, and covers.

Press these wing head nuts into the backside of a panel in applications where you have access to both sides of the panel. A quarter-turn locks and releases access panels, doors, and covers.

Also known as hitch pin clips and R-clips, use these cotter pins in applications requiring quick installation and removal.

Clevis pins have a hole for a cotter pin on one end to lock them in place.

Create fast connections with items, such as rope, chain, and straps.

Lock by screwing the latch into the body.

The narrow end restricts the movement of rope and chain, and the wide end allows room to attach multiple connectors.

Flat sides allow webbing and strapping to lay flat, so they won't slide and bunch.

Best for attaching different widths of webbing and strapping, the flat sides ensure they lay flat and won't bunch or slide.

Join, organize, and suspend objects with these S-hooks.

These hooks have closed ends on both sides.

Use in noncritical applications, such as fencing, where the strength of a forged clamp is not required. Install clamps so the saddle is on the long (live) end and the U-bolt is on the short (dead) end. They’re also known as wire rope clips.

Install these swivel-hook-end plug-lock fittings on the end of wire rope for a strong hold and finished appearance.

For areas with low clearance, these clamps have the mounting fastener to the side of the material, rather than on top.

Secure insulated pipe to strut channel without pinching the insulation or exposing the pipe. These clamps are sized for use with insulated pipe and have a plastic insert that creates a seal around the insulation to prevent the pipe from sweating, which can cause mold and corrosion.

For use with a single line, these clamps brace pipe, tubing, and conduit directly against the mounting surface.

Slide multiple clamps into existing strut channel to organize lines of pipe, tubing, and conduit without the need for drilling, welding, or using adhesive. Clamps have a plastic or rubber cushion or body to reduce vibration.

Temporarily route material across duct, racks, machinery, and other ferrous surfaces. Clamps fit tightly around pressurized lines in hydraulic systems to lessen vibration. Rubber cushions reduce wear from clamp edges and protect lines from corrosion caused by metal-to-metal contact.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface. A cushion covering the clamp reduces vibration and wear from clamp edges.

Support vertical pipes passing through floors.

These clamps rotate 360° and pivot 45° to ensure the rod hangs straight, even on sloped beams.

Add a crossbeam for hanging lifting equipment, creating overhead conveyor systems, and supporting structural applications.

Support strut channel at a right angle to the beam.

A secure way to hang threaded rod from a pair of angles, such as those used in ceiling joists, without the need to drill or weld. These clamps are commonly used to suspend HVAC, conveyor, and other overhead systems.

Load material between the two halves of the ring and adjust the side bolts for a tighter fit than standard threaded-rod-mount clamping hangers.

Also known as clevis hangers, these have a pivoting loop that adjusts for line movement and vibration. Combine with a threaded rod or other fastener to hang from the ceiling.