For frequently used doors, these closers last twice as long as standard door closers. They can replace Yale, Dorma, Falcon, Stanley, Parker, and Cal-Royal models with the same mounting hole pattern.

A built-in stop prevents doors from opening too far—good when wall- or floor-stops can’t be used. Designed for frequently used doors, these closers last twice as long as standard door closers. They can replace Yale, Dorma, Falcon, Stanley, Parker, and Cal-Royal models with the same mounting hole pattern.

Make existing door closers with lost or damaged covers look new again.

There's no need to mount a closer to your door or frame—these take the place of an existing hinge pin.

Often used on large freezer and cold-storage doors, these closers are designed for doors that weigh 200 lbs. or more.

Nudge your door and these openers will open it the rest of the way.

Stop unauthorized personnel from opening doors in your facility—these barricades help you meet lockdown regulations and advisory protocols.

Mounted diagonally so one end is higher than the other, the motion of an opening door tightens the torsion spring; as it unwinds, it closes the door.

These closers consist of two interconnected springs—twist them to adjust closing force. The springs retract to pull storm doors and gates closed.

Simple and compact, these closers have an arm that rolls along gates to push them closed.

Use these closers when your door-to-door clearance is limited. They close storm doors more smoothly than standard spring closers.

Push your door open to automatically engage the holder; pull on the door to release.

A magnet holds the door open; pull on the door to release.

Small enough to slip into a pocket, these foldable wedges are good for workers who frequently need to prop doors open as they move from job to job. Slide them under the door to hold it open.

Push your door open to automatically engage the holder; pull on the door to release.

Place one of these wire springs onto your door's hinge pin to keep it open.

Mount one end to the frame and the other end to your door to prevent it from opening too far.

Latch your door to the wall for a secure hold.

Pull a chain to manually open overhead doors.

If you don't have your remote, you can still open and close automatic overhead doors with a private 4-digit PIN.

Also known as jackshafts, these openers operate 24-ga. or thinner overhead doors.

To eliminate slamming and smashed fingers, these supports automatically pull lids shut when they approach the closed position. Raise the lid until the hold-open mechanism on the support is engaged; slightly lift it again to release the hold and close the lid.

Also known as hatch springs, these supports are commonly used on hatches and other top-opening lids. Raise the lid to extend the spring, which props the lid open—an internal cable keeps the spring from overextending. Press the center of the spring to release the hold and close the lid.

Keep environments free of contaminants—with plastic bushings, there's no metal-to-metal contact that can release particles as these supports open and close. Manually control these free-moving lid supports through their full range of motion. Raise the lid until the hold-open mechanism on the support is engaged; slightly lift it again to release the hold and close the lid.

Requiring less space to mount and operate, these supports are often used on small cabinets and enclosures. They gradually slow your lid's motion to prevent it from slamming open. To open lids, lower them and the support will slowly and softly do the rest. Manually shut the lids and the supports will hold them in the closed position.

No separate hinges are required, these supports act as a hinge and lid support all in one. Springs provide lifting assistance to raise and hold lids open—slightly lift the lid to get it started and the support will do the rest. Manually shut the lids and the supports will hold them in the closed position.

Use these openers on casement windows.

Mount these balancers in the corner of a horizontal frame to suspend, lift, or lower objects that move vertically in a track such as windows, doors, and panels.

To prevent doors from slamming, these latches are hydraulic.

Manually seal lids on 5-gallon open-head steel pails.

These chain pulls are more durable than rope pulls to operate doors, vents, skylights, and overhead equipment.