About Structural Adhesives
More
Flexible Instant-Bond Adhesives
Accommodate joint movement with these adhesives that remain pliable when cured. Also known as super glue. Use an accelerator (sold separately) to shorten the time it takes the adhesive to reach full strength.
Container | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Mfr. Model No. | Size, fl. oz. | Type | Max. Gap Size Filled | Begins to Harden | Reaches Full Strength | Consistency (Viscosity) | Elongation | Temp. Range, °F | Color | For Joining | Each | |
Loctite® Adhesives | ||||||||||||
| 4902 | 0.7 | Bottle | 0.004" | 10 sec. | 24 hrs. | Thin Liquid (200 cP) | 155% | -65° to 180° | Clear | Ceramic, Composites, Glass, Metal, Plastic, Rubber, Wood | 000000000 | 000000 |
Flexible Light-Activated Instant-Bond Adhesives
These adhesives stay pliable for flexible bonds that resist cracking. For easy positioning, they begin to harden only when exposed to light.
1700A257 and 2454N1 fluoresce under UV light for easy inspection.
Container | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Size, fl. oz. | Type | Max. Gap Size Filled | Begins to Harden | Reaches Full Strength | Light Intensity Requirements to Reach Full Strength | Cure Type | Consistency (Viscosity) | Elongation | Temp. Range, °F | Color | For Joining | Each | |
Adhesives | |||||||||||||
| 1.69 | Bottle | 0.25" | 5 sec. | 30 min. | 5 sec. @ 100 mW/cm2 | UV Light | Thin Liquid (850 cP) | Not Rated | 45° to 80° | Clear | Ceramic, Composites, Glass, Metal, Plastic, Rubber | 000000 | 000000 |
Light-Activated Instant-Bond Adhesives
For easy positioning, these adhesives begin to harden only when exposed to light.
Thin liquids flow to fill small gaps between close-fitting parts.
Container | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Mfr. Model No. | Size, fl. oz. | Type | Max. Gap Size Filled | Begins to Harden | Reaches Full Strength | Light Intensity Requirements to Reach Full Strength | Cure Type | Consistency (Viscosity) | Temp. Range, °F | Color | For Joining | Each | |
Loctite® Adhesives | |||||||||||||
| 4311 | 1 | Bottle | 0.008" | 5 sec. | 24 hrs. | 10 sec. @ 30 mW/cm2 | UV Light, Visible Light | Thin Liquid (1,050 cP) | -65° to 200° | Green | Ceramic, Composites, Glass, Metal, Plastic, Rubber, Wood | 000000 | 000000 |
Slow-Set Epoxy Structural Adhesives
To allow time to adjust and position parts, these epoxies remain workable for at least 90 minutes. The strongest and most weather- and chemical-resistant structural adhesives, epoxies work especially well on metals.
The size listed is the combined total of the two parts.
Mfr. Model | Container | Strength | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Name | No. | Size, fl. oz. | Type | Begins to Harden | Reaches Full Strength | Shear, lbs./sq. in. | Peel | Mix Ratio | Consistency (Viscosity) | Max. Temperature, °F | For Joining | Each | |
| Original | 50165 | 0.85 | Syringe | 4 hrs. | 24 hrs. | 1,800 | Not Rated | 1:1 | Paste (150,000 cP) | 550° | Metal, Plastic, Rubber, Composites, Glass, Masonry | 000000 | 00000 |
Waterproof Epoxy Structural Adhesives
Even when used under water, these adhesives maintain their strength. The most weather- and chemical-resistant structural adhesives, epoxies tend to work especially well on metals.
The size listed is the combined total of the two parts.
Mfr. Model | Container | Strength | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Name | No. | Size, fl. oz. | Type | Begins to Harden | Reaches Full Strength | Shear, lbs./sq. in. | Peel | Mix Ratio | Consistency (Viscosity) | Temp. Range, °F | Color | Environment | For Joining | Each | |
| MarineWeld | 50172 | 0.85 | Syringe | 5 min. | 1 hrs. | 1,800 | Not Rated | 1:1 | Paste (100,000 cP) | -20° to 300° | White | Salt Spray, Submersible | Metal, Plastic, Rubber, Composites, Glass, Masonry, Wood | 000000 | 000000 |
Quick-Set Epoxy Structural Adhesives
For quick repairs, these epoxies begin to harden in 6 minutes or less. Epoxies are the strongest and most weather- and chemical-resistant structural adhesives.
The size listed is the combined total of the two parts. Use cartridges with a dispensing gun and mixer nozzle to simultaneously mix and dispense adhesives.
HY4090 is a blend of epoxy and instant-bond adhesive for a balance of strength, cure speed, and temperature resistance.
50132 works especially well on plastics and composites.
Container | Strength | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Mfr. Model No. | Size, fl. oz. | Type | Begins to Harden | Reaches Full Strength | Shear, lbs./sq. in. | Peel | Mix Ratio | Consistency (Viscosity) | Temp. Range, °F | Color | For Joining | Each | |
| HY4090 | 1.69 | Cartridge | 3 min. | 7 days | 2,420 | Not Rated | 1:1 | Thick Liquid (19,000 cP) | -65° to 300° | Gray | Metal, Plastic, Rubber, Composites, Masonry, Wood | 00000000 | 000000 |
| HY4090 | 1.69 | Cartridge | 3 min. | 7 days | 2,420 | Not Rated | 1:1 | Thick Liquid (19,000 cP) | -65° to 300° | Off-White | Metal, Plastic, Rubber, Composites, Masonry, Wood | 00000000 | 00000 |
| HY4090 | 13.5 | Cartridge | 3 min. | 7 days | 2,420 | Not Rated | 1:1 | Thick Liquid (19,000 cP) | -65° to 300° | Off-White | Metal, Plastic, Rubber, Composites, Masonry, Wood | 0000000 | 000000 |
Mfr. Model | Container | Strength | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Name | No. | Size, fl. oz. | Type | Begins to Harden | Reaches Full Strength | Shear, lbs./sq. in. | Peel | Mix Ratio | Consistency (Viscosity) | Temp. Range, °F | Color | For Joining | Each | |
| PlasticWeld | 50132 | 0.85 | Syringe | 5 min. | 60 min. | 2,000 | Not Rated | 1:1 | Thick Liquid (9,000 cP) | -20° to 300° | Yellow | Metal, Plastic, Rubber, Composites, Masonry, Wood | 000000 | 00000 |
| Each | ||
| Mixer Nozzle for 1.69 fl. oz. Loctite® Cartridges | 000000000 | 00000 |
| Mixer Nozzle for 6.76 fl. oz. and 13.5 fl. oz. Cartridges | 000000000 | 0000 |
| Air-Powered Dispensing Gun for 1.69 fl. oz. Loctite® Cartridges | 000000000 | 000000 |
| Dispensing Gun for 1.69 fl. oz. Cartridges | 00000000 | 00000 |
| Dispensing Gun for 13.5 fl. oz. Cartridges | 0000000 | 000000 |
Toughened Epoxy Structural Adhesives
Toughened adhesives are blended with rubber particles for better impact resistance than standard epoxies. They form flexible, resilient bonds. The most weather- and chemical-resistant structural adhesives, epoxies work especially well on metals. Choose an adhesive that hardens quickly for fast repairs, or one that hardens slowly to allow more time for positioning.
The size listed is the combined total of the two parts. Use with a dispensing gun and mixer nozzle to simultaneously mix and dispense adhesives.
DP420NS, DP460NS, E-40HT, and 9462 are nonsagging, so they won't drip from vertical or overhead surfaces.
Container | Strength | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Mfr. Model No. | Size, fl. oz. | Type | Begins to Harden | Reaches Full Strength | Shear, lbs./sq. in. | Peel, lbs./in. wd. | Mix Ratio | Consistency (Viscosity) | Temp. Range, °F | Color | For Joining | Each | |
| DP420 | 1.69 | Cartridge | 20 min. | 24 hrs. | 280 | 50 | 2:1 | Thick Liquid (30,000 cP) | -65° to 350° | Off-White | Metal, Plastic, Composites | 0000000 | 000000 |
| DP420 | 1.69 | Cartridge | 20 min. | 24 hrs. | 400 | 50 | 2:1 | Thick Liquid (30,000 cP) | -65° to 350° | Black | Metal, Plastic, Composites | 0000000 | 00000 |
| DP420 | 6.76 | Cartridge | 20 min. | 24 hrs. | 280 | 50 | 2:1 | Thick Liquid (30,000 cP) | -65° to 350° | Off-White | Metal, Plastic, Composites | 0000000 | 000000 |
| DP420 | 6.76 | Cartridge | 20 min. | 24 hrs. | 400 | 50 | 2:1 | Thick Liquid (30,000 cP) | -65° to 350° | Black | Metal, Plastic, Composites | 00000000 | 000000 |
| DP420 | 13.5 | Cartridge | 20 min. | 24 hrs. | 280 | 50 | 2:1 | Thick Liquid (30,000 cP) | -65° to 350° | Off-White | Metal, Plastic, Composites | 00000000 | 000000 |
| DP420 | 13.5 | Cartridge | 20 min. | 24 hrs. | 400 | 50 | 2:1 | Thick Liquid (30,000 cP) | -65° to 350° | Black | Metal, Plastic, Composites | 00000000 | 000000 |
| DP420NS | 1.69 | Cartridge | 20 min. | 24 hrs. | 470 | 50 | 2:1 | Paste (180,000 cP) | -65° to 350° | Black | Metal, Plastic, Composites | 00000000 | 00000 |
| DP420NS | 6.76 | Cartridge | 20 min. | 24 hrs. | 470 | 50 | 2:1 | Paste (180,000 cP) | -65° to 350° | Black | Metal, Plastic, Composites | 00000000 | 000000 |
| DP420NS | 13.5 | Cartridge | 20 min. | 24 hrs. | 470 | 50 | 2:1 | Paste (180,000 cP) | -65° to 350° | Black | Metal, Plastic, Composites | 00000000 | 000000 |
| DP460 | 1.69 | Cartridge | 60 min. | 24 hrs. | 2,500 | 60 | 2:1 | Thick Liquid (30,000 cP) | -65° to 350° | Off-White | Metal, Plastic, Composites | 0000000 | 00000 |
| DP460 | 6.76 | Cartridge | 60 min. | 24 hrs. | 2,500 | 60 | 2:1 | Thick Liquid (30,000 cP) | -65° to 350° | Off-White | Metal, Plastic, Composites | 0000000 | 000000 |
| DP460 | 13.5 | Cartridge | 60 min. | 24 hrs. | 2,500 | 60 | 2:1 | Thick Liquid (30,000 cP) | -65° to 350° | Off-White | Metal, Plastic, Composites | 00000000 | 000000 |
| DP460NS | 1.69 | Cartridge | 60 min. | 24 hrs. | 2,680 | 60 | 2:1 | Paste (125,000 cP) | -65° to 350° | Off-White | Metal, Plastic, Composites | 0000000 | 00000 |
| DP460NS | 6.76 | Cartridge | 60 min. | 24 hrs. | 2,680 | 60 | 2:1 | Paste (125,000 cP) | -65° to 350° | Off-White | Metal, Plastic, Composites | 00000000 | 000000 |
| DP460NS | 13.5 | Cartridge | 60 min. | 24 hrs. | 2,680 | 60 | 2:1 | Paste (125,000 cP) | -65° to 350° | Off-White | Metal, Plastic, Composites | 0000000 | 000000 |
| Each | ||
| Mixer Nozzle for 1.69 fl. oz. 3M Cartridges (Step Tip) | 0000000 | 00000 |
| Mixer Nozzle for 1.69 fl. oz. 3M Cartridges (Taper Tip) | 0000000 | 0000 |
| Mixer Nozzle for 6.76 fl. oz. and 13.5 fl. oz. 3M Cartridges | 0000000 | 0000 |
| Replacement Plunger for 1.69 fl. oz. 3M Cartridges | 0000000 | 00000 |
| Dispensing Gun for 1.69 fl. oz. 3M Cartridges | 0000000 | 000000 |
| Dispensing Gun for 6.76 fl. oz. 3M Cartridges | 0000000 | 000000 |
| Air-Powered Dispensing Gun for 1.69 fl. oz. 3M Cartridges | 0000000 | 000000 |
Optically Clear Epoxy Structural Adhesives
For invisible bond lines, these adhesives dry clear. Epoxies are the strongest and most weather- and chemical-resistant structural adhesives. Choose an epoxy that hardens quickly for fast repairs, or one that hardens slowly to allow more time for positioning.
The size listed is the combined total of the two parts. Use cartridges with a dispensing gun and mixer nozzle to simultaneously mix and dispense adhesives.
0151 and E-30CL are suitable for fiber-optic applications.
Container | Strength | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Mfr. Model No. | Size, fl. oz. | Type | Begins to Harden | Reaches Full Strength | Shear, lbs./sq. in. | Peel, lbs./in. wd. | Mix Ratio | Consistency (Viscosity) | Temp. Range, °F | For Joining | Each | |
| E-30CL | 1.69 | Cartridge | 30 min. | 24 hrs. | 3,100 | Not Rated | 2:1 | Thick Liquid (10,000 cP) | -65 to 250° F | Metal, Plastic, Ceramic, Glass | 0000000 | 000000 |
| E-30CL | 6.76 | Cartridge | 30 min. | 24 hrs. | 3,100 | Not Rated | 2:1 | Thick Liquid (10,000 cP) | -65 to 250° F | Metal, Plastic, Ceramic, Glass | 0000000 | 00000 |
| Each | ||
| Mixer Nozzle for 1.69 fl. oz. Loctite® Cartridges | 00000000 | 00000 |
| Mixer Nozzle for 6.76 fl. oz. Loctite® Cartridges | 0000000 | 0000 |
| Dispensing Gun for 1.69 fl. oz Loctite® Cartridges | 00000000 | 00000 |
| Dispensing Gun for 6.76 fl. oz. Loctite® Cartridges | 0000000 | 000000 |
| Air-Powered Dispensing Gun for 1.69 fl. oz. Loctite® Cartridges | 000000000 | 000000 |
Urethane Structural Adhesives
Urethane adhesives are the most flexible, so they bond dissimilar materials and damp vibration.
The size listed is the combined total of the two parts. Use 1.64 fl. oz. and 1.69 fl. oz. cartridges with a dispensing gun and mixer nozzle to simultaneously mix and dispense adhesives. Dispense adhesives in 10.1 fl. oz. cartridges with a standard caulk gun.
U-05FL, U-09FL, and U-09LV won't yellow.
5570 is also known as silane modified polymer.
Container | Strength | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Mfr. Model No. | Size, fl. oz. | Type | Begins to Harden | Reaches Full Strength | Shear, lbs./sq. in. | Peel | Consistency (Viscosity) | Temp. Range, °F | Color | For Joining | Each | |
| 5570 | 10.1 | Cartridge | 30 min. | 7 days | 400 | Not Rated | Paste (Not Rated) | -40° to 200° | White | Metal, Metal to Plastic, Metal to Rubber, Metal to Composites, Metal to Glass, Plastic, Plastic to Rubber, Plastic to Composites, Plastic to Glass, Plastic to Masonry, Rubber, Rubber to Composites, Rubber to Glass, Rubber to Masonry, Composites, Glass, Masonry, Wood, Wood to Glass | 00000000 | 000000 |
Container | Strength | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Mfr. Model No. | Size, fl. oz. | Type | Begins to Harden | Reaches Full Strength | Shear, lbs./sq. in. | Peel | Mix Ratio | Consistency (Viscosity) | Temp. Range, °F | Color | For Joining | Each | |
| UK U-09FL | 1.69 | Cartridge | 10 min. | 24 hrs. | 1,460 | Not Rated | 1:1 | Thick Liquid (5,000 cP) | -65° to 250° | Clear | Metal, Metal to Plastic, Plastic, Wood | 0000000 | 000000 |
Mfr. Model | Container | Strength | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Name | No. | Size, fl. oz. | Type | Begins to Harden | Reaches Full Strength | Shear, lbs./sq. in. | Peel | Mix Ratio | Consistency (Viscosity) | Temp. Range, °F | Color | For Joining | Each | |
| Plastic Bonder | 50139 | 0.85 | Syringe | 15 min. | 30 min. | 1,000 | Not Rated | 1:1 | Thick Liquid (50,000 cP) | -20° to 250° | Black | Metal, Metal to Plastic, Metal to Rubber, Metal to Composites, Plastic, Plastic to Rubber, Plastic to Composites, Plastic to Masonry, Rubber, Rubber to Composites, Rubber to Masonry, Composites, Masonry, Wood | 000000 | 00000 |
High-Strength Acrylic Structural Adhesives
With excellent shear strength, these acrylics form stronger bonds than our standard acrylic structural adhesives. Acrylics bond to the widest range of materials, especially plastics, and require the least amount of surface preparation.
The size listed is the combined total of the two parts. Use cartridges with a dispensing gun and mixer nozzle to simultaneously mix and dispense adhesives.
DP8407NS and DP8410NS are nonsagging, so they won't drip from vertical or overhead surfaces. They contain 0.01" glass beads to prevent adhesive from squeezing out during clamping and give a consistent bond thickness.
Container | Strength | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Mfr. Model No. | Size, fl. oz. | Type | Begins to Harden | Reaches Full Strength | Shear, lbs./sq. in. | Peel, lbs./in. wd. | Mix Ratio | Consistency (Viscosity) | Temp. Range, °F | Color | For Joining | Each | |
3M Scotch-Weld Adhesives | |||||||||||||
| DP8407NS | 1.52 | Cartridge | 7 min. | 24 hrs. | 4,500 | 50 | 10:1 | Thick Liquid (20,000 cP) | -40° to 400° | Gray | Metal, Plastic, Rubber, Composites | 0000000 | 000000 |
| DP8410NS | 1.52 | Cartridge | 10 min. | 24 hrs. | 3,900 | 60 | 10:1 | Thick Liquid (60,000 cP) | -40° to 280° | Green | Metal, Plastic, Composites | 0000000 | 00000 |
Acrylic Structural Adhesives
Acrylics bond to the widest range of materials, especially plastics, and require the least amount of surface preparation.
The size listed is the combined total of the two parts. Use a dispensing gun and mixer nozzle to simultaneously mix and dispense adhesives.
H4500 works especially well on metals.
Container | Strength | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Mfr. Model No. | Size, fl. oz. | Type | Begins to Harden | Reaches Full Strength | Shear, lbs./sq. in. | Peel, lbs./in. wd. | Mix Ratio | Consistency (Viscosity) | Temp. Range, °F | Color | For Joining | Each | |
Loctite® Adhesives | |||||||||||||
| H4500 | 1.69 | Cartridge | 15 min. | 72 hrs. | 3,100 | 58 | 10:1 | Thick Liquid (14,380 cP) | -40° to 210° | Gray | Metal, Plastic | 0000000 | 000000 |
Adhesives with Mixer Nozzle | |||||||||||||
| __ | 1.69 | Cartridge | 5 min. | 24 hrs. | 3,200 | 7 | 1:1 | Thick Liquid (64,000 cP) | -40° to 250° | Light Green | Metal, Metal to Plastic, Metal to Rubber, Metal to Composites, Plastic, Plastic to Composites, Plastic to Masonry, Rubber, Rubber to Composites, Rubber to Masonry, Composites, Masonry | 000000 | 00000 |
| __ | 13.5 | Cartridge | 5 min. | 24 hrs. | 3,200 | 7 | 1:1 | Thick Liquid (64,000 cP) | -40° to 250° | Light Green | Metal, Metal to Plastic, Metal to Rubber, Metal to Composites, Plastic, Plastic to Composites, Plastic to Masonry, Rubber, Rubber to Composites, Rubber to Masonry, Composites, Masonry | 000000 | 00000 |
| Each | ||
| Mixer Nozzle for 1.69 fl. oz. Loctite® Cartridges | 00000000 | 00000 |
| Mixer Nozzle for 6.76 fl. oz. and 13.5 fl. oz. Cartridges | 0000000 | 0000 |
| Plunger for 1.69-oz. Cartridges (10:1 Mix Ratio) | 00000000 | 00000 |
| Dispensing Gun for 1.69 fl. oz. Loctite® Cartridges | 00000000 | 00000 |
| Dispensing Gun for 1.69 fl. oz. Cartridges (1:1 Mix Ratio) | 00000000 | 00000 |
| Dispensing Gun for 13.5 fl. oz. Cartridges | 0000000 | 000000 |
Acrylic Structural Adhesives with Spacing Beads
To keep these adhesives from squeezing out during clamping and give a consistent bond thickness, they're mixed with small glass beads.
The size listed is the combined total of the two parts. Use a dispensing gun and mixer nozzle to simultaneously mix and dispense adhesives.
DP8805NS and DP8810NS are toughened to form resilient, impact-resistant bonds.
Container | Strength | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Mfr. Model No. | Size, fl. oz. | Type | Begins to Harden | Reaches Full Strength | Shear, lbs./sq. in. | Peel, lbs./in. wd. | Mix Ratio | Consistency (Viscosity) | Temp. Range, °F | Color | For Joining | Each | |
3M Scotch-Weld Adhesives | |||||||||||||
| DP8805NS | 1.52 | Cartridge | 5 min. | 24 hrs. | 3,900 | 25 | 10:1 | Thick Liquid (45,000 cP) | -20° to 280° | Green | Metal, Plastic, Rubber, Composites | 0000000 | 000000 |
| DP8810NS | 1.52 | Cartridge | 10 min. | 24 hrs. | 3,600 | 35 | 10:1 | Thick Liquid (45,000 cP) | -20° to 280° | Green | Metal, Plastic, Rubber, Composites | 0000000 | 00000 |
Toughened Acrylic Structural Adhesives
Toughened adhesives are blended with rubber particles for better impact resistance than standard acrylics. They form resilient bonds. Acrylics bond to the widest range of materials, especially plastics, and require the least amount of surface preparation.
The size listed is the combined total of the two parts. Use cartridges with a dispensing gun and mixer nozzle to simultaneously mix and dispense adhesives.
MA310 bonds dissimilar materials.
Mfr. Model | Container | Strength | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Name | No. | Size, fl. oz. | Type | Begins to Harden | Reaches Full Strength | Shear, lbs./sq. in. | Peel, lbs./in. wd. | Mix Ratio | Consistency (Viscosity) | Temp. Range, °F | Color | For Joining | Each | |
| MA310 | 31500 | 1.58 | Cartridge | 15 min. | 24 hrs. | 3,000 | 15 | 1:1 | Thick Liquid (55,000 cP) | -65° to 250° | Light Yellow | Metal, Metal to Plastic, Plastic, Plastic to Composites, Plastic to Masonry, Composites, Masonry, Wood | 00000000 | 000000 |
Nonwhitening Cement for Acrylic
When appearance is important, this cement dries clear and forms strong bonds on acrylic.
Cement that cannot be sold to the areas listed exceeds local regulatory limits on VOCs (volatile organic compounds).
Cement | |||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Container | Dispensing Guns | Mixer Nozzles | |||||||||||||||
| Mfr. Model No. | Size | Type | Begins to Harden | Reaches Full Strength | Mix Ratio | Consistency | Viscosity | Temp. Range | Color | For Joining | Cannot Be Sold To | Each | Each | Each | |||
SciGrip Cement | |||||||||||||||||
| 4 | 4 fl. oz. | Can | 60 sec. | 7 days | __ | Thin Liquid | Not Rated | Not Rated | Clear | Plastic | CT; DC; DE; MA; MD; ME; NH; NJ; NY; PA; RI; UT; VT; Northern VA; Los Angeles County, CA; Orange County, CA; Riverside County, CA; San Bernardino County, CA; Ventura County, CA | 000000 | 000000 | 000000 | 00 | 000000 | 00 |
| 4 | 16 fl. oz. | Can | 60 sec. | 7 days | __ | Thin Liquid | Not Rated | Not Rated | Clear | Plastic | CT; DC; DE; MA; MD; ME; NH; NJ; NY; PA; RI; UT; VT; Northern VA; Los Angeles County, CA; Orange County, CA; Riverside County, CA; San Bernardino County, CA; Ventura County, CA | 000000 | 00000 | 000000 | 00 | 000000 | 00 |
| 4SC | 4 fl. oz. | Can | 60 sec. | 7 days | __ | Thin Liquid | Not Rated | Not Rated | Clear | Plastic | Los Angeles County, CA; Orange County, CA; Riverside County, CA; San Bernardino County, CA; Ventura County, CA | 000000 | 00000 | 000000 | 00 | 000000 | 00 |
| 4SC | 16 fl. oz. | Can | 60 sec. | 7 days | __ | Thin Liquid | Not Rated | Not Rated | Clear | Plastic | Los Angeles County, CA; Orange County, CA; Riverside County, CA; San Bernardino County, CA; Ventura County, CA | 000000 | 00000 | 000000 | 00 | 000000 | 00 |
| 4SC | 1 gal. | Can | 60 sec. | 7 days | __ | Thin Liquid | Not Rated | Not Rated | Clear | Plastic | Los Angeles County, CA; Orange County, CA; Riverside County, CA; San Bernardino County, CA; Ventura County, CA | 00000000 | 000000 | 000000 | 00 | 000000 | 00 |
| 40 | 16 fl. oz. | Can | 20 min. | 7 days | 20:1 | Thick Liquid | Not Rated | Not Rated | Clear | Plastic | __ | 000000 | 00000 | 000000 | 00 | 000000 | 00 |
| 40 | 1 gal. | Can | 20 min. | 7 days | 20:1 | Thick Liquid | Not Rated | Not Rated | Clear | Plastic | __ | 00000000 | 000000 | 000000 | 00 | 000000 | 00 |
| 42 | 1.69 fl. oz. | Cartridge | 15 min. | 7 days | 10:1 | Thick Liquid | Not Rated | Not Rated | Clear | Plastic | __ | 00000000 | 00000 | 0000000 | 000000 | 00000000 | 00000 |
| 42 | 7.8 fl. oz. | Cartridge | 15 min. | 7 days | 10:1 | Thick Liquid | Not Rated | Not Rated | Clear | Plastic | __ | 00000000 | 00000 | 000000 | 00 | 000000000 | 0000 |
Coolant-Resistant Surface Fillers
Repair small leaks and cracks in coolant systems for commercial vehicles and industrial equipment. These surface fillers meet ASTM D3147 for their ability to stop leaks in engine cooling systems. Pour them into your coolant to fix both internal and external leaks. They contain ceramic microfibers and copper particles to create a permanent seal. They’re compatible with antifreeze and other coolant system additives.
Container | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Size, fl. oz. | Type | Begins to Harden, min. | Reaches Full Strength, min. | Consistency | Temp. Range, °F | Color | For Use On | Each | |
| 16 | Jug | 7 | 10 | Thick Liquid | Not Rated to 500° | Brown | Aluminum, Brass, Bronze, Copper, Silver, Steel, Stainless Steel, Galvanized Steel, Galvanized Iron, Titanium, Acrylic Plastic, Polystyrene Plastic, Polycarbonate Plastic, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Nylon Plastic, PTFE Plastic, Polyethylene Plastic, Polypropylene Plastic | 0000000 | 000000 |
Water-Resistant Surface Fillers
Mix these two-part epoxy surface fillers to create a strong repair in wet environments or underwater. Use them to repair cracked, worn, and damaged surfaces. Size listed is the combined total of the two parts.
Paste fillers resist alkalies, solvents, gasoline, and oil.
Container | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Size, fl. oz. | Type | Begins to Harden, min. | Reaches Full Strength | Consistency | Mix Ratio | Approx. Coverage @ Thick. | Max. Thick. | Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
Surface Fillers | |||||||||||||
| 2 | Tube | 5 | 60 min. | Paste | 1:1 | 12 sq. in. @ 1/4" | 1/2" | Not Rated to 200° | Gray | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Bronze, Copper, Steel, Galvanized Iron, Galvanized Steel, Titanium, Acrylic Plastic, ABS Plastic, PVC Plastic, CPVC Plastic, Polyimide Plastic, Nylon Plastic, Vinyl Plastic, EPDM Rubber, Fiberglass, Glass, Concrete, Ceramic, Porcelain, Plaster, Grout, Masonry, Asphalt, Stone, Wood | 0000000 | 000000 |
| 2 | Jar, Bottle | 20 | 24 hrs. | Paste | 5:1 | 8 1/2 sq. in. @ 1/4" | 1 1/2" | Not Rated to 185° | White | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Bronze, Copper, Steel, Galvanized Iron, Galvanized Steel, Titanium, Acrylic Plastic, ABS Plastic, PVC Plastic, CPVC Plastic, Polyimide Plastic, Nylon Plastic, Vinyl Plastic, EPDM Rubber, Fiberglass, Glass, Concrete, Ceramic, Porcelain, Plaster, Grout, Masonry, Asphalt, Stone, Wood | 0000000 | 00000 |
| 2 | Jar, Bottle | 20 | 24 hrs. | Paste | 5:1 | 8 1/2 sq. in. @ 1/4" | 1 1/2" | Not Rated to 250° | Gray | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Bronze, Copper, Steel, Galvanized Iron, Galvanized Steel, Titanium, Acrylic Plastic, ABS Plastic, PVC Plastic, CPVC Plastic, Polyimide Plastic, Nylon Plastic, Vinyl Plastic, EPDM Rubber, Fiberglass, Glass, Concrete, Ceramic, Porcelain, Plaster, Grout, Masonry, Asphalt, Stone, Wood | 0000000 | 00000 |
| 14 | Can, Jar | 20 | 24 hrs. | Paste | 5:1 | 62 sq. in. @ 1/4" | 1 1/2" | Not Rated to 185° | White | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Bronze, Copper, Steel, Galvanized Iron, Galvanized Steel, Titanium, Acrylic Plastic, ABS Plastic, PVC Plastic, CPVC Plastic, Polyimide Plastic, Nylon Plastic, Vinyl Plastic, EPDM Rubber, Fiberglass, Glass, Concrete, Ceramic, Porcelain, Plaster, Grout, Masonry, Asphalt, Stone, Wood | 0000000 | 00000 |
| 14 | Can, Jar | 20 | 24 hrs. | Paste | 5:1 | 62 sq. in. @ 1/4" | 1 1/2" | Not Rated to 250° | Gray | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Bronze, Copper, Steel, Galvanized Iron, Galvanized Steel, Titanium, Acrylic Plastic, ABS Plastic, PVC Plastic, CPVC Plastic, Polyimide Plastic, Nylon Plastic, Vinyl Plastic, EPDM Rubber, Fiberglass, Glass, Concrete, Ceramic, Porcelain, Plaster, Grout, Masonry, Asphalt, Stone, Wood | 0000000 | 00000 |
Fuel-Resistant Surface Fillers
Also known as sloshing compounds, these two-part epoxies bond to rough and rusty surfaces in fuel tanks to repair leaks and prevent further corrosion. They withstand permanent immersion in fuel, oil, and harsh solvents. Use them with metal, plastic, and fiberglass tanks. Mix the smaller can with the bigger one and pour into your fuel tank. Rotate the tank to coat the interior and dump out any excess. Allow to cure overnight. Size listed is the combined total of the two parts.
1.5-pint container can treat a 10-gallon fuel tank. 3-pint container can treat a 20-gallon fuel tank.
Container | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Size, pt. | Type | Begins to Harden, min. | Reaches Full Strength, hrs. | Consistency | Mix Ratio | For Use Outdoors | Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
| 1.5 | Can | 5 | 24 | Thick Liquid | 2:1 | No | 70° to 90° | Amber | Drill, Sand, Tap | Aluminum, Brass, Bronze, Copper, Silver, Steel, Stainless Steel, Cast Iron, Galvanized Iron, Galvanized Steel, Titanium, Acrylic Plastic, Polycarbonate Plastic, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Nylon Plastic, Polyethylene Plastic, Polypropylene Plastic, Vinyl Plastic, Fiberglass, Ceramic, Porcelain | 0000000 | 000000 |
| 3 | Can | 5 | 24 | Thick Liquid | 2:1 | No | 70° to 90° | Amber | Drill, Sand, Tap | Aluminum, Brass, Bronze, Copper, Silver, Steel, Stainless Steel, Cast Iron, Galvanized Iron, Galvanized Steel, Titanium, Acrylic Plastic, Polycarbonate Plastic, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Nylon Plastic, Polyethylene Plastic, Polypropylene Plastic, Vinyl Plastic, Fiberglass, Ceramic, Porcelain | 0000000 | 00000 |