Longer-lasting than antislip tape, these coatings contain grit to provide traction. They’re good for areas with pedestrian traffic.

Water-based epoxy coatings are clear and can be applied over nearly any surface, even old coatings, without altering their appearance. These two-part coatings come with a mixer that attaches to a hand-held drill and a roller cover to apply them once mixed. The size listed is the combined total of the two parts.

Apply gallon-sized water-based coatings with a roller. Coatings that comply with OSHA 29 CFR 1910.22 meet requirements for walking-working surfaces.

These coatings meet UL 723 and are rated Class A by ASTM E84—the highest rating available—for their ability to limit the spread of flames and generation of smoke. Use them in kitchens, furnace areas, and ships on plastic, metal, wood, and masonry. Apply with a brush, roller, or sprayer. The size listed is the combined total of the two parts.

Clear coatings are frequently used on wood—use one coat on sealed wood and two on unsealed. They can be used outside without breaking down, but prolonged exposure to UV light may cause them to yellow.

White coatings are frequently used on walls, ceilings, doors, and stairwells.

Protect clothing, furniture, and other fabric with these oil- and water-repellent coatings. Also known as oleophobic and hydrophobic coatings, they work into a fabric’s individual fibers, repelling liquid and grease without altering its appearance, feel, or smell.

Seal brick, mortar, and concrete to prevent water damage. These coatings create a thin, clear layer that sits on the surface of masonry and repels water. Use them in exterior, above-grade vertical surfaces to minimize deterioration and to prevent salt deposits and surface stains. Apply with a brush or sprayer.

Cover scratches and wear on storage racks and carts. Match the color to your manufacturers' equipment color.

These sheets are made of rubber and iron oxide, letting you create a nonmetallic, nonmagnetic surface that magnets will stick to. Sheets can be cut with scissors to create custom shapes and sizes.

These thin primers penetrate deeply into concrete floors to create a hard surface that can then be coated with any urethane or epoxy coating. Primers resist abrasion and chemicals, such as mild acids, alkalies, salt, and fuel. Apply with a roller. The size listed is the combined total of the two parts.

These surface fillers come in a pen for precision application. After applying, use the LED on the back of the pen to instantly cure. They can be used with most types of metal as well as ceramic, stone, and porcelain.

Mix these two-part epoxy surface fillers to create a strong repair in wet environments or underwater. Use them to repair cracked, worn, and damaged surfaces. Size listed is the combined total of the two parts.

Paste fillers resist alkalies, solvents, gasoline, and oil.

Fill cracks in horizontal, vertical, and overhead concrete surfaces. Surface fillers that have a mix ratio are multi-part fillers. Size listed is the combined total of the parts.

Surface fillers in a 10.1 fl. oz. cartridge can be dispensed with a standard caulk gun (sold separately). They flex as concrete expands and contracts with temperature changes. Acrylic fillers are textured to blend in easily and clean up with water. Polyurethane fillers allow for more joint movement than acrylic fillers.

Surface fillers in a 9 fl. oz. cartridge include a mixer nozzle but require a caulk gun with a 26:1 thrust ratio (sold separately). These epoxy fillers can be used underwater.

Surface fillers in a pail can repair large areas. They resist abrasion, impact, and chemicals without the use of a sealer. The resin, hardener, and aggregate are in separate containers that can be mixed in the pail.

Stop active leaks of up to 50 gallons per minute in concrete, brick, and stone. These crack fillers begin to harden within seconds to create a permanent fix that won't shrink. When fully cured they create a seal that can withstand pressure of up to 2,000 psi. Apply with a dispensing gun (sold separately). The size listed is the combined total of the two parts. A mixer nozzle is included.

Stop slow-flowing and weeping leaks in concrete. These crack fillers begin to harden in three to five minutes to create a permanent fix that won't shrink.

Polyurethane fillers are thin to penetrate deep into cracks. When fully cured they create a seal that can withstand pressure of up to 2,000 psi. Apply with a standard caulk gun (sold separately). For especially large cracks, use a packer (sold separately) with a grease gun or a grout pump.

To use cement fillers, mix with water.

Use these two-part compounds to patch concrete floors, stairs, and walls in cold environments, such as freezers. At room temperature, they cure faster than any of our other concrete patching compounds. Once cured, they withstand impact, abrasion, and chemicals. The size listed is the combined total of the two parts.

Polyurea compounds are ready for foot traffic in ten minutes and vehicle traffic in 30 minutes. They are self-leveling, but can be mixed with sand (not included) and applied with a trowel.

Cover large sections of damaged concrete with these durable patching compounds. Made up of a resin, hardener, and aggregate, they cover more area than any of our other concrete patching compounds. Use them to fix pitted, worn, and cracked concrete floors, stairs, and loading docks. Compounds resist salt water, oil, and chemicals, and stand up to forklift and truck traffic. The resin, hardener, and aggregate come in separate containers that can be mixed in the pail. Use the squeeze bottle for precision applications, such as in cracks and holes. The size listed is the combined total of the parts.

Fill in and shape horizontal, vertical, and overhead concrete surfaces, such as steps and columns.

Mix cement surface fillers with water. They can be used to fill holes up to 7" deep. These quick-setting fillers are ready for foot traffic in just 30 minutes. Application time, after mixing, is 7 minutes.

Epoxy surface fillers are nonsagging. They resist oil, grease, water, alkalies, and chemicals. Application time, after mixing, is 1 hour. The size listed is the combined total of the two parts.

For use when thickness will be more than 2", concrete mixes consist of cement, sand, and gravel. Mix them with water. Concrete is ready for foot traffic when it reaches full strength.

For use when thickness will be less than 2", sand mixes consist of cement and sand. Mix them with water. They are ready for foot traffic at full strength.

Repair holes and seal gaps in roofing and gutters. These patching compounds are durable and water resistant.

Apply acrylic compounds to dry surfaces. Apply asphalt compounds to wet or dry surfaces.

Roll out a fast fix for leaky roofs and gutters with these peel-and-stick rolls. Backing is rubberized asphalt adhesive. Roll can be cut to size. Use primer (sold separately) for optimal adhesion.

These patching compounds are the most flexible and watertight we offer. Developed for use on flashing, chimneys, and high-stress areas, they are highly vibration resistant.

Dispense compounds in a cartridge in a standard caulk gun (sold separately).

Compounds that cannot be sold to the regions listed exceed local regulatory limits on VOCs (volatile organic compounds).

Make a temporary repair to cracks in any flat roof. These patching compounds are a powder that forms a thick gel in minutes when poured directly into standing water and rain.

Reinforce hot- and cold-applied asphalt patching compounds and coatings with this flexible fabric.

Used for brick, block, and stone laying as well as for repairing masonry, mortar mixes consist of fine sand and masonry cement. Mix it with water.

Used on ceramic, concrete, and stone floor and wall tiles, grout consists of fine sand, masonry cement, and coloring. Apply with a grout float.

Mix cement grout with water.

Acrylic grout does not require mixing. It resists shrinking, cracking, and staining.