These pumps can be submerged or connected remotely to a pipe in your line. Use them to circulate water in small tanks, cooling baths, fountains, and other low-flow applications. Plug in to activate. Do not run dry. Not for use with salt water or flammable liquids.

The durable epoxy-coated aluminum housing handles hard knocks in rough waters. Submerge these pumps to circulate water in small tanks, cooling baths, fountains, and other low-flow applications. Plug in to activate. Do not run dry. Not for use with salt water or flammable liquids.

Hardwire pumps must be wired to a plug (not included).

Protected from impact by a durable epoxy-coated aluminum housing, these pumps can be submerged or connected remotely to a pipe in your line. Use to circulate water in small tanks, cooling baths, fountains, and other low-flow applications. Plug in to activate. Do not run dry. Not for use with salt water or flammable liquids.

Hardwire pumps must be wired to a plug (not included).

Also known as deep-well submersible pumps, use these pumps to transfer drinking water from wells and cisterns up to 25 ft. deep. They come with a control box that automatically disconnects from the system when the lid is opened, making servicing easier. Pumps are activated by a pressure switch and must be hardwired. Do not run dry.

Magnets turn the impeller so there's no shaft seal to wear out. Submerge these pumps to circulate water in small tanks, cooling baths, fountains, and other low-flow applications. Plug in to activate. Do not run dry.

These pumps can be submerged or connected remotely to a pipe in your line. Magnets turn the impeller so there's no shaft seal to wear out. Use to circulate water in small tanks, cooling baths, fountains, and other low-flow applications. Plug in to activate. Do not run dry.

Submerge these pumps to circulate machine and cutting oil with a viscosity up to 9 centipoise. Plug in to activate. Do not run dry.

Circulate salt water in submerged and open-air applications. These pumps use magnets to turn the impellers so there is no shaft seal to wear out. They must be wired to a plug (not included) to activate. Do not run dry.

These pumps circulate solvent-based parts-washing solutions. Submerge in solutions that are UL classified as PJQU (flash point no lower than 100° F). Pumps must be wired to a plug (not included) to activate. Do not run dry. Not for use in heated parts washer applications.

Use these pumps to move higher volumes of water with solids than other sump pumps. They activate when plugged in; add a plug-in switch to control when the pump activates. Also known as effluent pumps, they accommodate solids up to 3/4" in diameter. They are often used with liquid waste that has passed through a septic tank, so most solids are removed. Pumps have an epoxy-coated cast iron housing that stands up to demanding environments. Submerge while in use and do not run dry.

Pumps with wire leads can be connected to a three-pronged plug or wired directly to a power source.

Also known as effluent pumps, these accommodate solids up to 3/4” in diameter. They’re often used with liquid waste that has passed through a septic tank, so most solids are removed. The float switch is wired to the pump. All have an epoxy-coated cast iron housing that stands up to demanding environments. Submerge while in use and do not run dry.

Use these pumps at temperatures up to 200° F. Also known as effluent pumps, they accommodate solids up to 3/4" in diameter. They’re often used with liquid waste that has passed through a septic tank, so most solids are removed. The float switch is wired to the pump. Pumps have an epoxy-coated cast iron housing that stands up to demanding environments. Submerge while in use and do not run dry.

Replacement float switches (sold separately) include a float, connecting wires, and a seal.

The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump. Also known as effluent pumps, these accommodate solids up to 3/4" in diameter. They’re often used with liquid waste that has passed through a septic tank, so most solids are removed. All have an epoxy-coated cast iron housing that stands up to demanding environments. Submerge while in use and do not run dry.

These pumps activate when plugged in. You can add a plug-in switch to control when the pump activates. Also known as effluent pumps, these accommodate solids up to 3/4" in diameter. They’re often used with liquid waste that has passed through a septic tank, so most solids are removed. They have an epoxy-coated cast iron housing that stands up to demanding environments. Submerge while in use and do not run dry.

This pump can handle high temperatures up to 200° F. It activates when plugged in; add a plug-in switch to control when the pump activates. Also known as an effluent pump, it accommodates solids up to 3/4" in diameter. It is often used with liquid waste that has passed through a septic tank, so most solids are removed. Pump has an epoxy-coated cast iron housing that stands up to demanding environments. Submerge while in use and do not run dry.

A cast iron housing stands up to demanding environments. Use these pumps to remove accumulated water from sump pits, loading docks, and cooling towers. The float switch is wired to the pump. Use with debris-free water. Submerge while in use and do not run dry.

The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump. Use this pump to remove accumulated water from sump pits, loading docks, and cooling towers. It has a cast iron housing that stands up to demanding environments. Use with debris-free water. Submerge while in use and do not run dry.

Convenient for applications where a sump pit is impractical, these pumps include a basin with a vent on top. Pumps have a switch that activates on increasing pressure caused by rising water levels. Use with debris-free water.

Remove accumulated water from sump pits, loading docks, and cooling towers. The float switch is wired to the pump. Use with debris-free water. Submerge while in use and do not run dry.

These pumps activate when plugged in. You can add a plug-in switch to control when the pump activates. Pumps remove accumulated water from sump pits, loading docks, and cooling towers. They have a cast iron housing that stands up to demanding environments. Use with debris-free water. Submerge while in use and do not run dry.

Pumps activate when plugged in. You can add a plug-in switch to control when the pump activates. Equipped with a large intake and rugged impeller, these pumps transfer raw sewage water with solids up to 2" in diameter. They have a cast iron housing that stands up to demanding environments. Submerge while in use and do not run dry.

Pump with wire leads can be connected to a three-pronged plug or wired directly to a power source.

Equipped with a large intake and a rugged impeller, this pump transfers raw sewage water with solids up to 2" in diameter. It has a cast iron housing that stands up to demanding environments. The float switch is wired to the pump. Submerge while in use and do not run dry.

The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump. Equipped with a large intake and rugged impeller, these pumps transfer raw sewage water with solids up to 2" in diameter. They have a cast iron housing that stands up to demanding environments. Submerge while in use and do not run dry.

Since the switch activates on increasing pressure caused by rising water levels, these pumps have no external moving parts to catch on sump pit walls. Use them to remove accumulated water from sump pits, loading docks, and cooling towers. They should be used with debris-free water. Submerge while in use and do not run dry.

Pumps with a cast iron housing are stronger than pumps with a bronze housing to stand up to demanding environments.

Pumps with a bronze housing are more corrosion resistant than pumps with a cast iron housing.

Switch maintenance kits (sold separately) include a bracket, a diaphragm O-ring, a screw, and a switch.

The switch activates on increasing pressure caused by rising water levels for a long service life. It has a separate cord, so you can replace the switch without replacing the whole pump. Use the handle to carry pumps from job to job. Install in debris-free water that’s at least 3/4" deep. Pumps are gravity fed and require an elevated liquid source to fully fill the pump before turning on. Do not run dry.

These pumps activate when plugged in. You can add a plug-in switch to control when the pump activates. Use the handle to carry pumps from job to job. Install in debris-free water that’s at least 3/4" deep. Pumps are gravity fed and require an elevated liquid source to fully fill the pump before turning on. Do not run dry.