Control six different outputs from a single source of airflow. These valves have one inlet port and six outlet ports. Push in and rotate the dial to move between outlet ports and send airflow to a different output.

Since both hands are required to simultaneously press the buttons, these valves protect workers from accidental machinery start-up. They create one action, such as extending a cylinder.

To prevent accidental start-up, these valves can be locked in their off position with a padlock. They create one action, such as extending a cylinder.

Because they require a key to operate, you can limit who is able to adjust these valves. They create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 4-way and 5/2 valves.

These valves close all ports in the off position to stop equipment in a locked position with air pressure holding it in place. They create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 4-way and 5/3 closed center valves.

Since both hands are required to simultaneously press the buttons, these valves protect workers from accidental machinery start-up. They create two actions, such as extending and then retracting a double-acting cylinder.

In the off position, these valves exhaust all air pressure, allowing the equipment to return to the neutral position. Also known as 4/3 exhaust-center valves, they create two actions, such as extracting and then retracting a double-acting cylinder.

A simple automation solution that requires no programming, these valves are activated when an object, such as a box rolling on a conveyor, pushes the actuator. They create one action, such as extending a cylinder. Also known as 3-way and 3/2 valves.

Often used to extend and then retract a cylinder at different speeds, these valves create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 5/2 valves, they actuate when voltage is applied to the electrical connection.

In the off position, these valves exhaust all air pressure, allowing the equipment to return to the neutral position. Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Apply voltage to the electrical connection to actuate.

Also known as 4-way valves, these valves create two actions, such as extending and then retracting a double-acting cylinder. Apply voltage to the electrical connection to actuate.

Run through equipment cycles up to 30% faster than with standard valves. These valves shift between flow positions in 1.7 ms. Also known as 3/2 valves, they create one action, such as extending a cylinder. Apply voltage to the electrical connection to actuate.

Create two actions at the same time, such as extending two single-acting cylinders at once. Apply voltage to the electrical connection to actuate. Also known as pressure center valves.

These valves are rated for environments where hazardous material is present. They actuate when voltage is applied to the electrical connection.

Rated IP69K, these valves withstand high-pressure, high-temperature washdowns. Their smooth design keeps out dust, dirt, and contaminants, making them easier to keep clean. Apply voltage to the electrical connection to actuate.

Also known as 4-way and 4/2 valves, these valves create two actions, such as extending and then retracting a cylinder. Use your foot to operate them, leaving your hands free to perform other tasks.

These valves create one action, such as extending a cylinder. Use your foot to operate them, leaving your hands free to perform other tasks. Also known as 3-way or 3/2 valves.

Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as pilot valves and 4-way valves, they use an air signal to actuate, so they're good for environments where electrical use may be dangerous.

Mix and match valve styles on one manifold to meet your control needs. Mount multiple valves to a manifold to reduce piping requirements and create multiple actions from a single pressure input.

These valves have a muffler to reduce exhaust noise. A padlock locks the handle in the shut-off position so you can disconnect air tools safely.

Control flow in two directions from a single source—these valves have two balls for independent control and shut-off of each outlet.

Install these valves on your air tank outlet—at the end of the day, they automatically close to save energy.

Also known as solenoid valves, these valves are operated by an electrical signal to turn airflow on or off.

When system pressure reaches the maximum, these valves open and send an air signal to turn on a downstream device such as a discharge valve or throttle. They close and send a signal to turn the device off when pressure drops.

Quickly vent exhaust air to the atmosphere or divert it to another place in your system to speed up the movement of equipment. The 90° elbow shape allows you to install them in tight spaces. Also known as quick exhaust valves.

A muffler reduces exhaust noise. Valves allow airflow into your equipment and then quickly dump exhaust air to the atmosphere without routing it back through a directional control valve to speed up the movement of equipment. Also known as quick exhaust valves.

Install these valves in the exhaust ports of air directional control valves to control exhaust air speed without needing access to your cylinder.

Convert a continuous stream of air into a series of quick pulses, reducing air consumption by up to 50% and improving performance in air-blowing applications such as cleaning and drying.

The traditional pressure switch. These power equipment, activate controls or alarms, or kick-off other actions when they reach a set pressure.

Use these switches for applications that need reliable switching but don’t require high accuracy.

With a set pressure range that works for most air systems, these switches send signals when your air system reaches a set pressure to your programmable logic controller (PLC) to activate automated controls and alarms.

When these switches reach a set pressure, they send electronic signals to your programmable logic controller (PLC) to activate automated controls or alarms.

When these switches reach either of their two set pressures—both of which can be controlled from a display—they send digital signals to your programmable logic controller (PLC) to activate automated controls or alarms.

Choose when these switches reset to control the pressure range between when they activate and deactivate, commonly referred to as deadband and differential.

With multiple ports, these switches maintain the air pressure of your electric air compressor, while also including ports for up to three air-powered devices, reducing the complexity of your air system setup.

Compatible with most air systems, these switches send digital signals to a programmable logic controller (PLC) to trigger separate processes when they reach either of their two set pressures. For example, they’ll activate a compressor if the pressure is too low or a relief valve if the pressure is too high.

These switches operate based on the difference in pressure between two process lines. When the differential pressure exceeds your setpoint, the switch is activated.

These switches are rated NEMA 4 for protection from dirt and washdowns.

Control the amount of vacuum change between when these switches activate and deactivate by adjusting when they reset.

Prevent changes to the set vacuum that powers equipment, activates controls, or signals alarms. The setpoint on these switches isn't adjustable.

Specifically made for air systems, these switches send signals to your programmable logic controller (PLC) to trigger processes when they reach a set vacuum.

Because these switches work with both positive and negative (vacuum) pressures, you can use them in applications that span both.

With two setpoints and outputs, these switches trigger different actions in your system by sending signals to a programmable logic controller (PLC) when they reach one of their set pressures or vacuums.

Specifically made for compressed air and gas systems, these transmitters remotely monitor pressure and vacuum.

Mount this switch through the top of your tank.

Flip the toggle to quickly turn these valves on and off. All have threads and a hex nut below the handle for installation in instrument panels. For extra gripping power and a strong seal, they have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. These valves are for use with water, oil, air, and inert gas.

About half the height of our other versa-mount valves, these fit in tight spots.

Limit wear and damage in high-cycling applications—these valves have additional seals that prevent leakage to reduce maintenance time.

Less than half the height of standard severe-duty valves, these fit in small spaces and low-clearance pipelines.

Their ball-valve design allows these valves to handle three times the flow of butterfly valves.

Also known as diaphragm valves, these have a diaphragm that can handle dirty liquid, slurries, and abrasive media without damage.

Use air pressure to automatically control the flow of liquids in sanitary environments, such as food and beverage processing plants.

Alter the set point with the adjustment screw to suit your application.

For use with threaded pipe, these valves have NPT connections. Use them with water, oil, air, and inert gas. All operate on compressed air to automatically divert flow between ports more quickly than motor-driven valves. You must control the air to the actuator using either an electric pilot valve or a manual on/off valve.