For tough jobs, these adhesives are 20% stronger than our standard concrete-anchoring adhesives. They can be applied at temperatures as low as -15° F, so they're suitable for refrigerated applications. Use them to permanently set threaded rods, studs, and rebar in concrete. They form a weather-resistant chemical bond that seals out moisture and resists vibration and dynamic loads better than mechanical anchors. Warning: Allowable pull-out strength is 25% of ultimate values or less, as required by building authorities.

Use the included mixer nozzle and a dispensing gun (sold separately) to simultaneously mix and dispense adhesive.

When concrete is saturated with or submerged in water, use these epoxies to permanently set threaded rods, studs, and rebar. They form a weather-resistant chemical bond that seals out moisture and resists vibration and dynamic loads better than mechanical anchors. Warning: Allowable pull-out strength is 25% of ultimate values or less, as required by building authorities. Use a mixer nozzle and dispensing gun (sold separately) to simultaneously mix and dispense adhesive.

Permanently set threaded rods, studs, and rebar in concrete with these kits. They include applicators and mixer nozzles to simultaneously mix and dispense the adhesive. These adhesives form a weather-resistant chemical bond that seals out moisture and resists vibration and dynamic loads better than mechanical anchors. Warning: Allowable pull-out strength is 25% of ultimate values or less, as required by building authorities.

Bond new concrete to old concrete, or use this epoxy as a primer for epoxy coatings on concrete surfaces. Mix the amount you need; the size listed is the combined total of the two parts.

These adhesives maintain their strength in temperatures up to 250° F. Use them to permanently set threaded rods, studs, and rebar in concrete. They form a weather-resistant chemical bond that seals out moisture and resists vibration and dynamic loads better than mechanical anchors. Warning: Allowable pull-out strength is 25% of ultimate values or less, as required by building authorities.

Use the included mixer nozzle and a dispensing gun (sold separately) to simultaneously mix and dispense adhesive.

Patch concrete floors, stairs, and walls with these compounds.

Epoxy compounds are three-part compounds consisting of a resin, a hardener, and aggregate in separate containers that can be mixed in the pail. The size listed is the combined total of the parts. They have excellent impact and chemical resistance. Paste compounds are ready for foot traffic in 8-12 hours. Thick liquid compounds are ready for traffic in two hours, and can withstand steel wheels and forklifts.

Use these two-part compounds to patch concrete floors, stairs, and walls in cold environments, such as freezers. At room temperature, they cure faster than any of our other concrete patching compounds. Once cured, they withstand impact, abrasion, and chemicals. The size listed is the combined total of the two parts.

Polyurea compounds are ready for foot traffic in ten minutes and vehicle traffic in 30 minutes. They are self-leveling, but can be mixed with sand (not included) and applied with a trowel.

Epoxy compounds are ready for foot traffic in ten minutes and vehicle traffic in two hours. Urethane compounds are ready for foot traffic in five minutes and vehicle traffic in ten minutes. Both can be applied with a trowel when mixed with the included aggregate or used as a self-leveling compound when used alone. Mix in the included pail.

Fill cracks in horizontal, vertical, and overhead concrete surfaces. Surface fillers that have a mix ratio are multi-part fillers. Size listed is the combined total of the parts.

Surface fillers in a 9-oz. cartridge include a mixer nozzle but require a caulk gun with a 26:1 thrust ratio (sold separately). These epoxy fillers can be used underwater.

Knead surface fillers in a stick to a uniform color to mix and press them into cracks in concrete floors, stairs, and walls. They can also be used to anchor bolts.

Surface fillers in a pail can repair large areas. They resist abrasion, impact, and chemicals without the use of a sealer. The resin, hardener, and aggregate are in separate containers that can be mixed in the pail.

Fill cracks up to 4" deep on horizontal surfaces such as floors and sidewalks. These epoxies are shrink, impact, and chemical resistant, and can also be used on wood, fiberglass, and metal surfaces. Use the cartridges with a standard caulk gun (sold separately) for dispensing.

Fill cracks up to 10" deep on vertical and overhead surfaces. To use this filler, secure the included injection ports to the crack with the two-part epoxy sealer, then spread sealer over the entire crack. Allow sealer 24 hours to cure. Application time for sealer, after mixing, is 40 minutes. To fill the rest of the void, use the cartridge with a standard caulk gun (sold separately) to dispense the two-part epoxy filler into the injection ports.

Not only do these leveling compounds withstand severe abrasion, wear, and impact, they stand up to heavy steel-wheel traffic and heavy blows without cracking. Apply with a trowel. They're ready for foot traffic in 12 hours. The resin and hardener are in separate containers that can be mixed in the pail. The size listed is the combined total of the two parts.

Give new life to damaged and worn concrete floors. These leveling compounds also fill minor depressions and cracks. Apply with a trowel.

Epoxy compounds resist abrasion for use in high-traffic areas. They’re ready for foot traffic in 8 hours. The resin and hardener are in separate containers that can be mixed in the pail. The size listed is the combined total of the two parts.

These leveling compounds stand up to acid and chemical spills, making them a good choice for corrosive environments. They also withstand steel-wheel traffic and heavy impact. Apply with a trowel. They're ready for foot traffic in 12 hours. The resin and hardener are in separate containers that can be mixed in the pail. The size listed is the combined total of the two parts.

Fill in and shape horizontal, vertical, and overhead concrete surfaces, such as steps and columns.

Mix cement surface fillers with water. They can be used to fill holes up to 7" deep. These quick-setting fillers are ready for foot traffic in just 30 minutes. Application time, after mixing, is 7 minutes.

Epoxy surface fillers are nonsagging. They resist oil, grease, water, alkalies, and chemicals. Application time, after mixing, is 1 hour. The size listed is the combined total of the two parts.

These coatings are more durable than our standard coatings for concrete floors. They provide a stain-resistant finish that protects your floors from moisture, chemicals, foot traffic, and hand carts. Repair cracks and holes prior to application. Apply with a squeegee, roller, or sprayer. The size listed is the combined total of the two parts.

Use these solvent-free, high-gloss coatings to protect concrete floors in enclosed areas. Durable enough for forklift traffic, they resist stains, moisture, and chemicals. Apply with a brush, roller, or sprayer. The size listed is the combined total of the two parts.

These thin primers penetrate deeply into concrete floors to create a hard surface that can then be coated with any urethane or epoxy coating. Primers resist abrasion and chemicals, such as mild acids, alkalies, salt, and fuel. Apply with a roller. The size listed is the combined total of the two parts.

Use these primers on concrete floors before antislip coatings to maximize longevity. They do not contain grit. Apply with a brush or roller. The size listed is the combined total of the two parts.