Built with snap-in tabs and a spring extension, these cord grips install into panel holes more quickly than standard grips and better prevent damage from sharp bends.

Made of nylon, these grips resist chemicals.

Secure and seal electrical cords entering knockouts at a 45° angle.

The mesh extension provides a secure hold in applications where cable is pulled or in motion. It reduces stress on the cable and prevents kinking for longer cable life.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance.

Tighten the screws to secure your cable.

Because these grips resist absorbing water, they are less likely to crack or corrode than other types of plastics and metals.

Snap these cord grips into place to secure cable in wet environments.

Wrap the split gland of these grips around ethernet cables with an RJ45 connector or other already installed cables for a water-resistant seal with your enclosure.

Secure cords installed through enclosures and panels in wet environments while protecting them against sharp bends. With a flared end that keeps cords from bending without limiting too much motion, these grips extend cord life.

Made of nylon with a nylon mesh extension, these grips resist most chemicals. The mesh provides a secure hold in applications where cable is pulled or in motion.

Secure cords in washdown areas where there’s minimal space—these cord grips curve 90° to relieve stress from bending.

Use these lightweight grips to secure cords entering knockouts at a 45° angle in wet, tight spaces while easing the stress from bending. Made of aluminum, they’re lighter in weight than steel and brass grips yet durable.

Create a tight grip on cords in wet environments while reducing stress from bending—the 90° angle of these cord grips routes cords to fit tight spaces in enclosures and panels.

Keep your cord at a gentle angle without sacrificing a tight hold, even in tough, wet environments.

Suitable for use in applications where cords are underwater—these grips are rated IP68 for protection from prolonged submersion.

Secure cable installed through enclosures in wet environments while venting air to protect electronics from condensation.

Made of nylon, these grips resist chemicals. Install them in panels and enclosures—they have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the enclosure.

The mesh offers a secure hold in applications where cable is pulled or in motion. It reduces stress on the cable and prevents kinking for longer cable life.

Stronger than aluminum cord grips, these steel grips are zinc plated for corrosion resistance. They have a steel locknut and metal-reinforced O-ring that prevents liquid from entering the connection.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance. They have a steel locknut and metal-reinforced O-ring that prevents liquid from entering the connection.

These cord grips are lightweight yet durable. They have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the connection.

These grips are nickel-plated brass for good corrosion resistance.

These grips meet Class III, Divisions 1 and 2 standards for use in hazardous locations.

FDA compliant for direct food contact, these cord grips have a multi-piece design to wrap around cables in sanitary environments without removing connectors or rewiring.

The face of these grips is flush with the cable-entry point for a seamless appearance. They have a thin, flexible seal that covers the holes until you push a cord through.

Modify these cord grips to get the right fit for your cord even when you don't know the exact diameter.

These grips have a thin, flexible seal that covers the holes until you push cords through.

Secure multiple flat cable through one cord grip—reducing the space and number you need for a project, as well as saving time.

A spring extension prevents sharp bends and kinks in your cord, prolonging its life. These bushings, which are more rigid than grommets, shield cords from rubbing against the edges of holes in enclosures and panels, so they won’t wear down.

Cut the thin layer of rubber in the center of these grommets to create custom IDs to securely hold and protect wire, cable, and cords. Push these grommets into place. They turn rough-edged and uneven holes into smooth, insulated holes. Commonly used in metal panels, they also damp vibration. Also known as webbed grommets.

The center hole has flaps that flex to hold and protect various sizes of wire, cable, and cords while keeping out dust and debris. Push these grommets into place. They turn rough-edged and uneven holes into smooth, insulated holes.

The center hole has flaps that flex to hold and protect various sizes of wire, cable, and cords while keeping out dust and debris. Snap these grommets into place and their wings expand against the sides of the hole to lock them in position. Use them to turn rough-edged and uneven holes into smooth holes.

A slit in the side of these grommets allows you to install them around wire, cable, and cords that are already in place. They snap into the hole and their wings hold them tight. Use them to turn rough-edged and uneven holes into smooth, insulated holes.

The center hole has flaps that flex to accommodate various sizes of wire, cable, and cords while still providing dust and debris protection. Use these grommets to eliminate cord clutter on desktops, countertops, benchtops, and other work surfaces.

Eliminate clutter on desktops, countertops, benchtops, and other work surfaces by organizing wire, cable, and cords.

Rated IP68, these grommets form liquid-tight seals around wire, cable, and cords to protect them against dust as well as submersion in a maximum of one meter of water.

The two‐piece design makes it easy to install and seal these grommets around wire, cable, and cords that are already in place. Use them to keep out dust, debris, and moisture.

Create a sanitary seal on through-wall piping, tubing, and cables in food-, cosmetic-, and pharmaceutical-processing areas.

Press these flexible grommets into holes and their tapered inner wall will expand when pipe or tubing is inserted to hold them snugly in place. They're often used for routing applications on metal, plastic, and fiberglass tanks.

The sharp neck on these grommets cuts the material as you press them into place, eliminating the need for a cutting punch. They strengthen and prevent holes from fraying in tarps, covers, and curtains. They also provide a way to run rope and cable through your material.

Press these grommets into a hole you've already cut. They strengthen and prevent holes from fraying in tarps, covers, and curtains. They also provide a way to run rope and cable through your material.

The extended neck on the washer of these grommets adds reinforcement so you can use them in thicker material such as woven fabrics. Press them into a hole you've already cut. They strengthen and prevent holes from fraying in tarps, covers, and curtains. They also provide a way to run rope and cable through your material.