These cord grips are lightweight yet durable.

Secure and seal electrical cords entering knockouts at a 45° angle.

Made of nylon, these grips resist chemicals.

Built with snap-in tabs and a spring extension, these cord grips install into panel holes more quickly than standard grips and better prevent damage from sharp bends.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance.

Able to stand up to rust better than steel grips, these 300 series stainless steel grips secure electrical cables in corrosive environments.

These grips are sized to fit in tight areas.

Because these grips resist absorbing water, they are less likely to crack or corrode than other types of plastics and metals.

Able to withstand temperatures up to 300° F, these grips are also corrosion- and chemical-resistant.

Extend your cord’s life while stopping it from coming loose in places that are sanitized with water or steam as hot as 300° F, such as food plants and clean rooms.

A rubber bushing with an oval slot resists water and provides entry for building cable, which is also known as Romex type NM-B or type UF-B cable.

Secure cords installed through enclosures and panels in wet environments while protecting them against sharp bends. With a flared end that keeps cords from bending without limiting too much motion, these grips extend cord life.

Made of PBT, these grips resist soaking up water in washdown and other wet environments while securing cords with an extra-strong hold.

Made of nylon with a nylon mesh extension, these grips resist most chemicals. The mesh provides a secure hold in applications where cable is pulled or in motion.

Suitable for use in applications where cords are underwater—these grips are rated IP68 for protection from prolonged submersion.

Secure cable installed through enclosures in wet environments while venting air to protect electronics from condensation.

Lighter in weight than steel and brass grips, these aluminum grips are strong enough to secure cords in demanding wet environments.

Create a tight grip on cords in wet environments while reducing stress from bending—the 90° angle of these cord grips routes cords to fit tight spaces in enclosures and panels.

Keep your cord at a gentle angle without sacrificing a tight hold, even in tough, wet environments.

Made of nylon, these grips resist chemicals. Install them in panels and enclosures—they have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the enclosure.

Also known as cable-entry seals, the cable-entry side has heat-shrinkable polyolefin with an adhesive lining.

These cord grips are lightweight yet durable. They have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the connection.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance. They have a steel locknut and metal-reinforced O-ring that prevents liquid from entering the connection.

These stainless steel grips offer the most protection from wet, corrosive environments of any of our metal wet-location cord grips. They are rated IP67 for protection from temporary water submersion.

These grips are nickel-plated brass for good corrosion resistance.

These grips meet Class III, Divisions 1 and 2 standards for use in hazardous locations.

Grips have a rubber inner grommet with multiple holes and a rubber O-ring that create a tight seal to prevent liquid from entering the connection.

The face of these grips is flush with the cable-entry point for a seamless appearance. They have a thin, flexible seal that covers the holes until you push a cord through.

Modify these cord grips to get the right fit for your cord even when you don't know the exact diameter.

The face of these grips is flush with the cable-entry point for a seamless appearance.

FDA compliant for direct food contact, these cord grips have a multi-piece design to wrap around cables in sanitary environments without removing connectors or rewiring.

More rigid than grommets, these bushings guard cords from rubbing against the edges of holes in enclosures and panels and wearing down.

A large angled opening provides an exit point for cords that run behind walls.

Use these general purpose connectors indoors in high vibration applications. A quarter turn locks them together when mated to remain secure in high-vibration applications.

A good fit for tight spaces, these connectors are also known as NEMA midget plugs. They turn to lock together when mated to prevent accidental disconnection.

When mated, these connectors meet NEMA 6P for protection against washdowns and temporary submersion.

Rated NEMA 6P, NEMA 13, IP66, and IP69K when mated, these connectors withstand high-pressure, high-temperature washdowns, oil/coolant splashing, and are corrosion-resistant so they can be used in high-vibration marine environments.

Use these connectors in general purpose residential and commercial applications.

A good fit for tight spaces, these are smaller than standard straight-blade plugs. Also known as NEMA midget plugs.

Eliminate the need for wire stripping; snap-on terminals pierce the wire insulation and grip the wire securely. Access the wire connection by opening the hinged housing.

Visually confirm that connectors have power; they have an indicating light that is visible from any angle.

Protect computers and other sensitive equipment from electromagnetic interference (EMI). Also known as isolated ground receptacles.

Visually confirm that sockets have power—the face lights up when they're connected. The rubber housing protects them from damage caused by drops and other impact.

Stainless steel hardware and nickel-plated blades or slots protect connections from damage in corrosive environments.

An indicating light that is visible from any angle lets you know when these plugs have power. They have an extra-tight fit when mated with a receptacle to withstand high vibration. Also known as hospital grade plugs.

Rated NEMA 6P and 13, IP66, and IP69K when mated, connectors withstand oil/coolant spraying, high-pressure, high-temperature washdowns, and are corrosion resistant so they can be used in marine environments.

These connectors are often used with 18 mm and 30 mm proximity switches and limit switches.

Because they tightly thread to M12 connections, these connectors won’t let contaminants in or come loose from vibration in rugged industrial environments and automated systems as they send power and signal or just power to your equipment.

Safely use these connectors with 12 mm proximity switches, console lights, valves, and power supplies in food, beverage, and pharmaceutical applications—they’re FDA compliant for direct food contact.

Plug these connectors into hazardous location devices. Using a NAMUR signal, they operate at a low current and voltage, so they prevent the risk of sparks and ignition in volatile areas.

The largest signal/power connectors we offer, these are often used with conveyors, cooling fans, and grinders.

Rated IP69K, these M16 connectors protect against dust, debris, and hot, high-pressure jets of water at high volumes.

Also known as pico connectors, these connectors are often used with 8 mm and smaller proximity switches and photoelectric switches.

Connect different pole configurations to join sensors, switches, and other devices to cords, distribution blocks, and I/O modules.

Join M8 connections to M12 connections.

Protect connections while maintaining access. The base and hood latch together securely yet can be quickly detached for equipment repair or replacement.

A rubber seal and stainless steel hardware give these connectors excellent chemical resistance. They're rated NEMA 12, 4X, and IP65 for protection against corrosion, oil, and washdown environments.

Assemble a connector that can handle multiple applications at once. Combine inserts that send power, signal, and data with a base and a hood.

Carry up to four times the current of standard Compact Latching Connectors. The base and hood latch together securely, yet can be quickly detached for equipment repair or replacement.

Rated to MIL-DTL-5015 specifications, these connectors are compatible with other products that meet the same standard. They screw together for a secure connection.

Connectors come assembled with wire leads already installed, so they can be quickly added to existing wiring systems. Use them with AMP MATE-N-LOK connectors.

Sets include a plug and socket with wire leads already installed, so they can be quickly added to existing wiring systems. They fit standard Molex plugs and sockets.

Stack as many connectors on top of each other as needed—the housings clamp together to form a secure attachment.

Quickly replace or add connectors to an existing wiring system—connectors come assembled with wire leads already installed. Also known as weather-pack connectors, they withstand moisture, harsh engine fluids, and high temperatures.

Configure a connector for your application by combining housings with pins and sleeves for different wire sizes. Also known as weather-pack connectors, they withstand moisture, harsh engine fluids, and high temperatures.

Meet international standards IEC 309-1 and 309-2.

Caps are watertight to protect safe-break plugs when not in use.

Use connectors where ignitable gas and dust may be present, such as in refineries and silos. They also prevent an electrical arc when separating mated connectors so you can safetly connect and disconnect with the power on.