These grips are sized to fit in tight areas.

Because these grips resist absorbing water, they are less likely to crack or corrode than other types of plastics and metals.

Able to withstand temperatures up to 300° F, these grips are also corrosion- and chemical-resistant.

Vent air from your enclosure to equalize pressure and stop condensation from forming inside while securing cords in wet environments. These polyamide grips are lightweight and resist rusting.

Secure cords installed through enclosures and panels in wet environments while protecting them against sharp bends. With a flared end that keeps cords from bending without limiting too much motion, these grips extend cord life.

A rubber bushing with an oval slot resists water and provides entry for building cable, which is also known as Romex type NM-B or type UF-B cable.

Wrap the split gland of these grips around ethernet cables with an RJ45 connector or other already installed cables for a water-resistant seal with your enclosure.

These grips are made of nylon, which resists most chemicals. The nylon mesh extension provides a secure hold when the cable is pulled or in motion.

Made of PBT, these grips resist soaking up water in washdown and other wet environments while securing cords with an extra-strong hold.

Lighter in weight than steel and brass grips, these aluminum grips are strong enough to secure cords in demanding wet environments.

Create a tight grip on cords in wet environments while reducing stress from bending—the 90° angle of these cord grips routes cords to fit tight spaces in enclosures and panels.

Use these lightweight grips to secure cords entering knockouts at a 45° angle in wet, tight spaces while easing the stress from bending. Made of aluminum, they’re lighter in weight than steel and brass grips yet durable.

Suitable for use in applications where cords are underwater—these grips are rated IP68 for protection from prolonged submersion.

Keep cords from coming loose and seal water out of enclosures in extremely cold labs and storage areas. Thanks to their plastic bushing and rubber O-ring, these grips withstand temperatures as low as -75° F.

Made of nylon, these grips resist chemicals.

Built with snap-in tabs and a spring extension, these cord grips install into panel holes more quickly than standard grips and better prevent damage from sharp bends.

These cord grips are lightweight yet durable.

Secure and seal electrical cords entering knockouts at a 45° angle.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance.

Able to stand up to rust better than steel grips, these 300 series stainless steel grips secure electrical cables in corrosive environments.

An insert clamps the cable in place to provide more strain relief than other snap-in cord grips for building cable.

Also known as cable-entry seals, the cable-entry side has heat-shrinkable polyolefin with an adhesive lining.

Made of nylon, these grips resist chemicals. Install them in panels and enclosures—they have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the enclosure.

Secure cords in wet and industrial environments with little room—these grips curve 45° to relieve bending stress.

These cord grips are lightweight yet durable. They have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the connection.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance. They have a steel locknut and metal-reinforced O-ring that prevents liquid from entering the connection.

These grips are nickel-plated brass for good corrosion resistance.

These 90° elbows meet Class III, Divisions 1 and 2 standards for use in hazardous locations.

Grips have a rubber inner grommet with multiple holes and a rubber O-ring that create a tight seal to prevent liquid from entering the connection.

The face of these grips is flush with the cable-entry point for a seamless appearance. They have a thin, flexible seal that covers the holes until you push a cord through.

Modify these cord grips to get the right fit for your cord even when you don't know the exact diameter.

The face of these grips is flush with the cable-entry point for a seamless appearance.

Secure multiple flat cable through one cord grip—reducing the space and number you need for a project, as well as saving time.

Attach conduit to a knockout in an outlet box or enclosure.

The spiral design makes this conduit more flexible than abrasion-resistant liquid-tight flexible plastic conduit.

Run conduit in food areas—the cover can be cleaned and sterilized without weakening or splitting. This conduit meets NSF/ANSI standard 169 for special-purpose food equipment.

The toughest liquid-tight flexible metal conduit we offer, this resists oil, chemicals, and extreme temperature fluctuations.

When used with liquid-tight fittings, this conduit seals out liquid. The steel core provides crush resistance, and the cover is UV light resistant.

Attach conduit to a knockout in an outlet box or enclosure.

Connect different sizes of conduit.

Thicker corrugations make this conduit more crush resistant than standard flexible plastic conduit.

Visually identify different runs of wire and cable in machine and equipment wiring.

Attach conduit to a knockout in an outlet box or enclosure.

Also known as FMC, this conduit offers the crush resistance of metal combined with flexibility to handle bends in tight spaces.

Attach conduit and armored cable to a knockout in an outlet box or enclosure.

Covered with a copper braid, this conduit protects wire and cable from electromagnetic interference (EMI) caused by motors and other equipment.

Attach conduit to a knockout in an outlet box or enclosure.

Join different sizes of conduit.

Reduce the knockout size in an outlet box or enclosure so you can attach a different size of conduit to it.

Seal out moisture while reducing the knockout size in an outlet box or enclosure so you can attach a different size of conduit to it.

Also known as conduit bodies, these ports provide access to wire and cable inside thick-wall (rigid) metal conduit for pulling, splicing, and maintenance. They are also used to change the direction of a run.

Join pieces of conduit.

Connect different sizes of conduit.

Join pieces of conduit.

Use in food-processing and chemical plants—this is the most corrosion resistant thick-wall conduit we offer.

Also known as conduit bodies, these ports provide access to wire and cable inside PVC conduit for pulling, splicing, and maintenance. They are also used to change the direction of a run.

Join pieces of conduit.

Attach conduit to a knockout in an outlet box or enclosure.

Join pieces of conduit.

Connect different sizes of conduit.

The most corrosion-resistant thin-wall conduit we offer, use this along walls and ceilings in food-processing and chemical plants.

Attach conduit to a knockout in an outlet box or enclosure.

Transition between types of conduit.

Secure threaded plastic conduit fittings to a knockout in an outlet box or enclosure.

Also known as Type A, this conduit meets the demands of continuous motion while sealing out liquid when used with liquid-tight fittings.

One end twists into a piece of conduit for a quick connection; the other end attaches to a knockout in an outlet box or enclosure.