These cord grips are lightweight yet durable.

Secure and seal electrical cords entering knockouts at a 45° angle.

Made of nylon, these grips resist chemicals.

These grips install into enclosure holes quickly to stabilize and relieve strain on cords.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance.

Able to stand up to rust better than steel grips, these 300 series stainless steel grips secure electrical cables in corrosive environments.

An insert clamps the cable in place to provide more strain relief than other snap-in cord grips for building cable.

These grips are sized to fit in tight areas.

Because these grips resist absorbing water, they are less likely to crack or corrode than other types of plastics and metals.

Able to withstand temperatures up to 300° F, these grips are also corrosion- and chemical-resistant.

Extend your cord’s life while stopping it from coming loose in places that are sanitized with water or steam as hot as 300° F, such as food plants and clean rooms.

Wrap the split gland of these grips around ethernet cables with an RJ45 connector or other already installed cables for a water-resistant seal with your enclosure.

A rubber bushing with an oval slot resists water and provides entry for building cable, which is also known as Romex type NM-B or type UF-B cable.

Snap these cord grips into place to secure cable in wet environments.

Made of nylon with a nylon mesh extension, these grips resist most chemicals. The mesh provides a secure hold in applications where cable is pulled or in motion.

Made of PBT, these grips resist soaking up water in washdown and other wet environments while securing cords with an extra-strong hold.

Lighter in weight than steel and brass grips, these aluminum grips are strong enough to secure cords in demanding wet environments.

With an oval bushing hole, these lightweight grips secure flat building cable, such as Romex and Festoon cable, in wet areas. All offer strain relief to extend cable life.

Use these lightweight grips to secure cords entering knockouts at a 45° angle in wet, tight spaces while easing the stress from bending. Made of aluminum, they’re lighter in weight than steel and brass grips yet durable.

Suitable for use in applications where cords are underwater—these grips are rated IP68 for protection from prolonged submersion.

These grips have an extension that provides extra support for moving cable and prevents kinking for longer cable life.

These stainless steel grips offer the most protection from wet, corrosive environments of any of our metal wet-location cord grips. They are rated IP67 for protection from temporary water submersion.

Made of nylon, these grips resist chemicals. Install them in panels and enclosures—they have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the enclosure.

Made of nylon, these grips resist chemicals. Install them in panels and enclosures—they have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the enclosure.

These cord grips are lightweight yet durable. They have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the connection.

Stronger than aluminum cord grips, these steel grips are zinc plated for corrosion resistance. They have a steel locknut and metal-reinforced O-ring that prevents liquid from entering the connection.

These grips are nickel-plated brass for good corrosion resistance.

These 90° elbows meet Class III, Divisions 1 and 2 standards for use in hazardous locations.

Grips have a rubber inner grommet with multiple holes and a rubber O-ring that create a tight seal to prevent liquid from entering the connection.

The face of these grips is flush with the cable-entry point for a seamless appearance. They have a thin, flexible seal that covers the holes until you push a cord through.

Peel away layers of rubber inserts to fit around cord grips, even when you don't know the exact diameter.

The face of these grips is flush with the cable-entry point for a seamless appearance.

FDA compliant for direct food contact, these cord grips have a multi-piece design to wrap around cables in sanitary environments without removing connectors or rewiring.

More rigid than grommets, these bushings guard cords from rubbing against the edges of holes in enclosures and panels and wearing down.

These grips are galvanized steel for good corrosion resistance.

Made of stainless steel, these grips have excellent corrosion resistance.

Made of stainless steel, these grips have excellent corrosion resistance.

Push these flexible grommets into place to protect wire, cable, and cords by turning rough-edged and uneven holes into smooth, insulated holes. Commonly used in metal panels, they also damp vibration.

Cut the thin layer of rubber in the center of these grommets to create custom IDs to securely hold and protect wire, cable, and cords. Push these grommets into place. They turn rough-edged and uneven holes into smooth, insulated holes. Commonly used in metal panels, they also damp vibration. Also known as webbed grommets.

These flexible grommets withstand temperatures of 450° F or greater, which is approximately twice as high as our standard grommets. Push them into place to protect wire, cable, and cords by turning rough-edged and uneven holes into smooth, insulated holes. Commonly used in metal panels, they also damp vibration.

These grommets snap into place and have wings that expand against the sides of the hole to lock them in position. Use them to protect wire, cable, and cords by turning rough-edged and uneven holes into smooth holes.

The two‐piece design makes it easy to install and seal these grommets around wire, cable, and cords that are already in place. Use them to keep out dust, debris, and moisture.

Snap these grommets into place to hold wire, cable, and cords in wet locations and form a seal against dust, debris, and water.

Create a sanitary seal on through-wall piping, tubing, and cables in food-, cosmetic-, and pharmaceutical-processing areas.

No setting tools needed—snap the two parts together in a hole you've already cut to strengthen the hole and eliminate fraying. Use these grommets in tarps, covers, curtains, and other material.

Kits include grommets, a cutting punch, a cutting block, an installation punch, and a die set. Use them to create a way to run rope and cable through tarps, covers, and curtains.

The sharp neck on these grommets cuts the material as you press them into place, eliminating the need for a cutting punch. They strengthen and prevent holes from fraying in tarps, covers, and curtains. They also provide a way to run rope and cable through your material.

Squeeze these flexible grommets to open the center flap—once wire, cable, and cords pass through, the flap closes tightly for dust and debris protection as well as a finished look. Use them to eliminate cord clutter on desktops, countertops, benchtops, and other work surfaces.

Eliminate clutter on desktops, countertops, benchtops, and other work surfaces by organizing wire, cable, and cords.

These grommets have two flanges that snap around holes and flex to compensate for misalignment and movement of pipe and tubing. They're often used for routing applications in panel walls.

Reduce cable strain caused by equipment hanging from drop-down cable.