The M12 threaded ends on these cords seal out contaminants and resist coming loose from vibration better than the RJ45 ends on traditional Ethernet cords. Use them in tough, rugged environments to send high-speed data between sensors, switches, servers, computers, and PLCs not protected by control panels. These cords can power devices as they send data, as long as devices are Power over Ethernet (PoE) compatible. They are often used within Ethernet/IP, Profinet, and EtherCat systems. Their poles and keyways adhere to standard coding layouts, reducing the chance you’ll mismatch connections.

All cords are backward compatible, so they work in networks that meet the same or lower ethernet cable category. For example, a Category 6 cord will work in a Category 5 network, but it will only run at the Category 5 speed.

A- and X-coded cords send data faster than D-coded cords, so they’re good for robotics and multi-step programs.

With either TPE or polyurethane insulation, all cords stand up to harsh factory conditions, chemicals, and UV rays. All are also highly flexible, so they’re good for jobs with continuous motion, such as robotics. TPE-insulated cords resist abrasion and won’t pit or crack from welding runoff.

Use unshielded cords where signal interference is not a concern. Double-shielded cords have layers of braid and foil that block signal interference from nearby devices, preventing impact to transmission speeds and data.

90° elbow cords sit flush against equipment, so they fit behind machinery in areas where space is tight.

When mated, all cords are IP67 rated to protect against dust and temporary submersion. IP65-rated cords stand up to washdowns. IP66K-rated cords stand up to high-pressure washdowns.

Add caps to protect cords and maintain their IP ratings when not in use.

For technical drawings and 3-D models, click on a part number.

To send high-speed data in tough, rugged environments, these cords have an M12 connector on one end that threads onto switches, sensors, and other devices prone to vibration. The other end has a traditional RJ45 plug that connects to Ethernet equipment, such as computers, IO modules, and programmable logic controllers (PLCs). These cords can also power devices as they send data, so you don’t need a separate power cord. But, the device must be Power over Ethernet (PoE) compatible. They’re often used with EtherNet/IP, Profinet, and EtherCAT systems. With TPE insulation, they stand up to bending in robotics applications. It also means they resist abrasion and won’t pit or crack from chemicals, sunlight, and welding runoff.

Thanks to its threads and IP rating, the M12 end is water and dust tight when mated. Poles and keyways on its face adhere to standard coding layouts, which reduces the chance of mismatching connections.

When choosing an Ethernet cord, make sure you match or exceed your network’s ethernet cable category. These cords are backward compatible—for example, a Category 6 cord will work in a Category 5 network, but it’ll only run at the Category 5 speed.

A- and X-coded cords send data faster than D-coded cords, so they’re best for systems that run multi-step programs, such as robotics.

Double-shielded cords have layers of braid and foil that block signal interference from nearby devices, maintaining their speed and data integrity.

Add caps to protect connectors and maintain their IP rating when not in use.

For technical drawings and 3-D models, click on a part number.

Also known as pico connectors, these are for low-current devices such as 8 mm and smaller proximity switches and photoelectric switches.

To view wiring diagrams, select a part number and click Product Detail.

Receptacles thread into panels and walls, so they work well in stationary or permanent installations.

Connectors with screw terminals hold wire by tightening a screw, so you don’t need to use soldering irons or crimpers. Connectors with a solder wire connection prevent strands of wire from fraying while creating a secure connection.

IP67 rated connectors protect against dust and temporary submersion. IP68 rated connectors protect against dust and submersion. NEMA 6 rated connectors protect against dust, washdowns, and temporary submersion.

Note: Sockets and female receptacles may have extra holes on the face that are not used.

For technical drawings and 3-D models, click on a part number.

Join two devices with M8 connectors to a single cord, distribution block, or I/O module with M12 connectors to save space and reduce the number of cords in industrial automation setups. Often used with sensors and switches, these splitters send or receive two signals through one connection. Rated IP65 and IP67, they’ll stand up to dust, low-pressure washdowns, and brief submersion.

Note: M12 plugs have an extra pin on the face that is not used.

For technical drawings and 3-D models, click on a part number.

One of the smallest signal/power connectors we offer. They have an A-coded face and are often used to send signal and power to automated systems and Profibus systems. All are rated IP67.

Sockets and female receptacles may have extra holes on the face that are not used.

For technical drawings and 3-D models, click on a part number.