Component Component |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement)  |
|---|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
About Masonry Drill Bits
More
Drill Bit Decimal Size Equivalents
More
About Drill Bits
More
Thread Adapters for Masonry Drill Bits for Drilling Rigs
Adapt a bit for use on a drilling rig with a different thread size.
| Overall Length | Male Thread Size | Female Thread Size | For Drill Bit Shank Type | Each | |
| 5 3/8" | 5/8"-11 | 1 1/4"-7 | Threaded Hub | 0000000 | 0000000 |
Changeable-Size SDS-Max-Shank Masonry Core Drill Bits for Rotary Hammers
These bits allow you to switch to another size by changing only the bit body. They are hollow and cut with their outside edge for drilling large holes. The SDS-Max shank has three deep slots and two shallow slots for use with SDS-Max-drive rotary hammers. They cannot be used with SDS-Plus-drive rotary hammers.
Drill holes using simultaneous rotary and hammering action to break masonry material into tiny granules. This type of bit drills faster and penetrates material with less pressure than rotary-only bits. Also known as percussion or impact bits. To achieve maximum drilling depth, break up and remove the core every 4” before drilling deeper.
For technical drawings and 3-D models, click on a part number.
| Drill Bit Size | Decimal Size Equivalent | Overall Lg. | Material | Specifications Met | Each | |
| 1 1/2" | 1.5" | 5" | Uncoated Carbide-Tipped Steel | ANSI B212.15 | 0000000 | 0000000 |
| 1 3/4" | 1.75" | 5" | Uncoated Carbide-Tipped Steel | ANSI B212.15 | 0000000 | 000000 |
| 2" | 2" | 5" | Uncoated Carbide-Tipped Steel | ANSI B212.15 | 0000000 | 000000 |
| 2 1/2" | 2.5" | 5" | Uncoated Carbide-Tipped Steel | ANSI B212.15 | 0000000 | 000000 |
| 3" | 3" | 5" | Uncoated Carbide-Tipped Steel | ANSI B212.15 | 0000000 | 000000 |
| 3 1/2" | 3.5" | 5" | Uncoated Carbide-Tipped Steel | ANSI B212.15 | 0000000 | 000000 |
| 4" | 4" | 5" | Uncoated Carbide-Tipped Steel | ANSI B212.15 | 0000000 | 000000 |
| 4 1/2" | 4.5" | 5" | Uncoated Carbide-Tipped Steel | ANSI B212.15 | 0000000 | 000000 |
| 5" | 5" | 5" | Uncoated Carbide-Tipped Steel | ANSI B212.15 | 0000000 | 000000 |
| Material | Each | |
| Steel | 00000000 | 000000 |
| For Drill Bit Size | Material | Each | |
| 1 1/2", 1 3/4", 2 1/2", 2", 3 1/2", 3", 4 1/2", 4", 5" | Carbide-Tipped Steel | 0000000 | 000000 |
Changeable-Size Spline-Shank Masonry Core Drill Bits for Rotary Hammers
These bits allow you to switch to another size by changing only the bit body. They are hollow and cut with their outside edge for drilling large holes. The shank has 12 splines for use with a spline-drive rotary hammer. Drill holes using simultaneous rotary and hammering action to break masonry material into tiny granules. This type of bit drills faster and penetrates material with less pressure than rotary-only bits. Also called percussion or impact bits.
For technical drawings and 3-D models, click on a part number.
| Material | Each | |
| Steel | 00000000 | 000000 |