You can set these counters up to count with or without voltage inputs based on the switch, sensor, or encoder you have. An output relay sends a signal to another device when the counter reaches a set point. The signal can start/stop a process or trigger an alarm. If power is lost, count backup maintains the count and programming backup maintains settings. A scaling function lets you adjust the unit of measure to suit your application.

Counter rated NEMA 4X is protected from dust and washdowns and can be used outdoors.

The digits displayed on these counters are visible up to 100 ft. away and the display can be adjusted to suit lighting conditions. You can set counters up to count with or without voltage inputs based on the switch, sensor, or encoder you have. They can be wired for remote reset. An output relay sends a signal to another device when a set point is reached. The signal can start/stop a process or trigger an alarm. Counters are protected from dust and washdowns and can be used outdoors (rated NEMA 4X). Programming backup maintains settings if power is lost.

Wire these counters/ratemeters to an electrical pulse-emitting switch, sensor, or encoder to count input while tracking rates in units such as gallons per minute. A scaling function lets you adjust the unit of measure to suit your application. Use the toggle button to switch between the count and the rate. Counter/ratemeter is protected from dust and washdowns and can be used outdoors (rated IP65).

For technical drawings and 3-D models, click on a part number.

For quick installation, these counters/ratemeters fit a standard 1/8 DIN panel cutout. Wire them up to an electrical pulse-emitting switch, sensor, or encoder to count input while tracking rates in units such as gallons per minute. The scaling function lets you adjust the unit of measure to suit your application. Counters are protected from dust and washdowns and can be used outdoors (rated NEMA 4X).

Optional output relays send a signal to another device when a set point is reached. The signal can start/stop a process or trigger an alarm.

For technical drawings and 3-D models, click on a part number.

This meter does not require voltage to register a count. It is protected from dust, water, and splashing oil and coolant (meets IP65, NEMA 4X, NEMA 12). Use it to display running time on a machine so you can schedule preventative maintenance.

With a display that can be placed up to 25 feet from the sensor, these flowmeter/totalizers are often used in hard-to-access areas. For a complete unit, order a display, a sensor, and a tee fitting.

Display can be programmed to show flow rate in gallons or liters per second, minute, hour, or day. It has an enclosure that meets NEMA 4X for protection from dust, washdowns, and corrosion.

For technical drawings and 3-D models, click on a part number.

To withstand water and a variety of caustic chemicals, these flowmeter/totalizers have a corrosion-resistant 316 stainless steel body. They measure both flow rate and total flow volume. The batch total volume can be reset after each metering application. The total flow volume cannot be reset. They have an enclosure that meets NEMA 4 for protection from dirt and washdowns.

Flowmeter/totalizers with threaded connections have 316 stainless steel seals, which resist corrosion.

Connect flowmeter/totalizers with quick-clamp connections to other quick-clamp fittings (often called tri-clamp fittings) using a gasket and clamp. They’re easy to attach and remove for cleaning.

Certificate of calibration traceable to NIST states that the flowmeter/totalizer has passed a test for accuracy.

Optional output module transmits output signals to an external device such as a data recorder, logger, or remote display (not included). It includes 10 feet of cable with wire leads.

Optional remote panel-mounting kit lets you mount the meter’s display up to 100 feet away. It includes a sensor module and 10 feet of cable with wire leads.

Hazardous location environmental ratings indicate where manufacturers have included safety features in products to facilitate their safe use in hazardous environments. Before selecting a product for a hazardous location, ensure it is rated for your environment. See About Hazardous Location Environmental Ratings.

Also known as encoders, these sanitary transmitters convey motion to an electrical signal that conveys distance, direction, and speed. They’re often used in control systems to automate servomotors, robotics, and assembly machines in sanitary environments such as food and pharmaceutical plants. Made of corrosion-resistant stainless steel, they won’t rust from frequent washdowns with harsh cleaners. These transmitters are sealed and have a highly polished surface, leaving no room for bacteria to grow and making them easier to clean. They’re rated IP67 for protection from dust, high-pressure jets of water, and submersion in up to a meter of water for 30 minutes.

To achieve a 4X resolution increase, use these transmitters with a controller that has quadrature detection.

Transmitters with three mounting holes are designed to fit on a three-hole servomotor face.

Connect transmitters to counters and controllers with cables (sold separately).

Use a flexible shaft coupling to connect the transmitter shaft to a drive shaft.

Check pH in harsh field conditions. These floating meters that have a housing that meets IP67 for complete resistance to dust and protection from temporary submersion. Automatic temperature compensation standardizes readings at 77° F to prevent inaccurate results in fluctuating temperatures. Use a calibration solution and the calibration button to maintain accuracy. They do not include Calibration Solution. Meters cannot be sold to Canada due to import regulations.

Meter for clean liquids is commonly used in pools and hydroponic solutions.

Meter for dirty liquids stands up to wastewater, plating bath solutions, and other harsh liquids.

Transmit pH readings to a PC for analysis. These meters have a sensor on a 6-ft. cable for taking remote readings of water and other clean liquids. They have automatic temperature compensation that standardizes readings at 77° F to prevent inaccurate readings in fluctuating temperatures. Use the included calibration solution and calibration button to maintain accuracy.

The remote sensor with a cable lets you take pH readings in hard-to-reach areas. Made of durable nonglass, it resists breaking. These meters are for use with dirty liquids, so they stand up to petrochemical, environmental, and agricultural testing. The water-resistant housing meets IP65 for protection from dust and low-pressure washdowns. Use the included calibration solution and calibration button to maintain accuracy.

These meters cannot be sold to the areas listed due to energy or import regulations.

Don’t worry about dropping this meter in your tank when checking electrical conductivity—it floats and has a housing that meets IP67 for complete resistance to dust and protection from temporary submersion. For use with water, hydroponic solutions, and other clean liquids, this meter measures a liquid's conductivity to indicate the concentration of salts, nutrients, chemicals, and other substances. It displays temperature in addition to conductivity. Automatic temperature compensation standardizes readings at 77° F to prevent inaccurate results in fluctuating temperatures. Use a Calibration Solution (not included) and the calibration button to maintain accuracy.

Since this oxidation reduction potential (ORP) meter has a housing that meets IP67 for complete resistance to dust and protection from temporary submersion, it’s often used to determine a solution’s ability to break down contaminants in harsh field conditions. For use with dirty liquids containing heavy metals, sulfides, and harsh chemicals, this meter is often used for wastewater treatment. Automatic temperature compensation standardizes readings at 77° F to prevent inaccurate results in fluctuating temperatures. Use a Calibration Solution (not included) and the calibration button to maintain accuracy. Meters cannot be sold to Canada due to import regulations.

Since these meters float and have a housing that meets IP67, they won’t be damaged by temporary submersion and have complete resistance to dust. They detect total dissolved solids (TDS) in water, hydroponic solutions, and other clean liquids to determine contaminant levels. Automatic temperature compensation standardizes readings at 77° F to prevent inaccurate results in fluctuating temperatures. Use a Calibration Solution (not included) and the calibration button to maintain accuracy.

Check the oxygen levels of water and other clean liquids in harsh field conditions. This meter has a housing that meets IP57 for good resistance to dust and protection from temporary submersion. It has automatic temperature compensation that standardizes readings at 77° F to prevent inaccurate results in fluctuating temperatures. Use distilled water and the calibration button to maintain accuracy.

Don’t strain your eyes reading a scale—these bench-top meters indicate exact results on the digital display. For complete resistance to dust and protection from temporary submersion, these meters float and have a housing that meets NEMA 6 and IP67. They're for use with water and other clean liquids. Automatic temperature compensation standardizes readings at 77° F to prevent inaccurate results in fluctuating temperatures. Use a Calibration Solution (not included) and the calibration button to maintain accuracy.

Take multiple water-chemistry and temperature measurements in hard-to-reach places from up to 3 feet away. Often used in tap water and wastewater, these meters work in both clean and dirty liquids. Automatic temperature compensation standardizes readings to 77° F to prevent inaccurate results in changing temperatures. The data hold function freezes the current reading on the display. For easy viewing, temperature and chemistry measurements appear on the same screen. These meters are IP57 rated, so they resist dust and withstand temporary submersion. They cannot be sold to Canada due to import regulations.

To maintain their accuracy, all have a calibration button and some also come with calibration solutions.

Conductivity, salinity, temperature, and total dissolved solids (TDS) meters take four measurements at once. Conductivity measures the concentration of salts, nutrients, chemicals, and other substances. Salinity measures the amount of dissolved salts. TDS determines the contaminant levels. The stainless steel sensor is durable and resists breaking.

Oxidation reduction potential (ORP), pH, and temperature meters take three measurements. ORP measures the amount of dissolved oxygen in liquids. It determines how efficiently a liquid breaks down contaminants.

Test temperature, chemical concentration, contamination, and salt levels in liquid from up to 6 ft. away, then send the results to your computer for analysis. These meters include a USB cable that transfers up to 1,000 readings. Often used to test water quality, they work on both clean and dirty liquids—from tap water to wastewater. Conductivity tests measure the concentration of salts, nutrients, chemicals, and other substances. Total dissolved solids (TDS) tests report contaminant levels. Salinity tests determine the salt levels in liquid. The sensor is made of stainless steel, so it’s durable and resists breaking. IP67 rated, these meters are dust tight and withstand temporary submersion.

To prevent inaccurate results from changing temperatures, these meters automatically standardize temperature readings at 77° F. Temperature readings appear on screen with other measurements, so you won’t have to scroll through multiple screens. A data hold function freezes the current reading on the display.

To maintain accuracy of the meters, they come with calibration solutions and have a calibration button.

These meters cannot be sold to Canada due to import regulations.

Check your indoor air quality (IAQ) by measuring the amount of particles present. These counters are often used to monitor dust levels in workshops, check for particles in classrooms, and measure filter efficiency in HVAC systems. The sensor probe detects and identifies particles of six different sizes, helping you confirm that your clean room complies with ISO Class requirements. First, use the zero count filter to establish a baseline before taking a sample. Then, either measure the amount of air particles detected within a set time range or the amount of air particles detected within a certain air volume. Counters store up to 10,000 readings in their internal memory, and you can transfer data to your computer via Ethernet or USB connection—no special software required. Compact, lightweight, and battery powered, these counters are portable and able to operate in tight spaces. They’re CE marked as compliant with European health, safety, and environmental standards.