For Shaft Diameter For Shaft Diameter | Show |
|---|
|
For Shaft Diameter For Shaft Diameter | Hide |
|---|
Material Material |
|---|
|
Construction Construction |
|---|
|
For Motion Type For Motion Type |
|---|
|
Set Screw Material Set Screw Material |
|---|
|
Set Screw Type Set Screw Type |
|---|
 | Hex Socket |
Component Component |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
|---|
Clamping Screw Material Clamping Screw Material |
|---|
|
Clamping Screw Type Clamping Screw Type |
|---|
|
Number of Clamping Screws Included Number of ClampingScrews Included |
|---|
|
Set Screw Finish Set Screw Finish |
|---|
|
About Shaft Couplings
More
About U-Joints (Universal Joints)
U-joints are used to connect two shafts that have a high amount of misalignment.
More
Set Screw Flexible Shaft Couplings
Each hub includes a set screw (unless noted), which bites into your shaft to hold the coupling in place. Also known as Lovejoy® couplings, these three-piece couplings have a spider-shaped cushion between two hubs to reduce shock and handle minor shaft misalignment.
A complete coupling consists of two hubs and one spider, or two hubs, one split spider, and one retaining ring (all components sold separately). Split spiders are easier to install and replace than standard spiders because there’s no need for tools or removing your hubs. Twist-lock them in place using a retaining ring.
Buna-N spiders provide good vibration damping and chemical resistance. Hytrel spiders provide fair vibration damping and excellent chemical resistance. Polyurethane spiders and split spiders provide fair vibration damping and good chemical resistance.
For technical drawings and 3-D models, click on a part number.
Buna-N Rubber Spiders | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
Iron Hubs | Misalignment Capability | |||||||||||
| Overall Lg. | OD | For Motion Type | For Shaft Dia. | Each | Max. Speed, rpm | Max. Torque, in.-lbs. | Parallel | Angular | Temp. Range, °F | Each | ||
| 2 27/32" | 2 35/64" | Forward/Reverse, Start/Stop | 1 3/16" | 0000000 | 000000 | 7,000 | 315 | 0.015" | 1° | -40° to 212° | 0000000 | 000000 |
| 3 31/64" | 2 35/64" | Forward/Reverse, Start/Stop | 1 3/16" | 0000000 | 00000 | 7,000 | 315 | 0.015" | 1° | -40° to 212° | 0000000 | 00000 |
| 4 7/32" | 3 21/64" | Forward/Reverse, Start/Stop | 1 3/16" | 0000000 | 00000 | 5,000 | 790 | 0.015" | 1° | -40° to 212° | 0000000 | 00000 |
| 4 1/2" | 3 3/4" | Forward/Reverse, Start/Stop | 1 3/16" | 0000000 | 000000 | 5,000 | 1,240 | 0.015" | 1° | -40° to 212° | 0000000 | 00000 |
| 4 7/8" | 4 1/2" | Forward/Reverse, Start/Stop | 1 3/16" | 0000000 | 000000 | 5,000 | 1,725 | 0.015" | 1° | -40° to 212° | 0000000 | 00000 |
| 5 11/32" | 5" | Forward/Reverse, Start/Stop | 1 3/16" | 0000000 | 000000 | 4,200 | 2,340 | 0.015" | 1° | -40° to 212° | 0000000 | 00000 |
Hytrel Rubber Spiders | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
Iron Hubs | Misalignment Capability | |||||||||||
| Overall Lg. | OD | For Motion Type | For Shaft Dia. | Each | Max. Speed, rpm | Max. Torque, in.-lbs. | Parallel | Angular | Temp. Range, °F | Each | ||
| 2 27/32" | 2 35/64" | Forward/Reverse, Start/Stop | 1 3/16" | 0000000 | 000000 | 3,600 | 790 | 0.015" | 0.5° | -55° to 245° | 0000000 | 0000000 |
| 3 31/64" | 2 35/64" | Forward/Reverse, Start/Stop | 1 3/16" | 0000000 | 00000 | 3,600 | 790 | 0.015" | 0.5° | -55° to 245° | 0000000 | 000000 |
| 4 7/32" | 3 21/64" | Forward/Reverse, Start/Stop | 1 3/16" | 0000000 | 00000 | 3,600 | 2,265 | 0.015" | 0.5° | -55° to 245° | 0000000 | 000000 |
| 4 1/2" | 3 3/4" | Forward/Reverse, Start/Stop | 1 3/16" | 0000000 | 000000 | 3,600 | 3,705 | 0.015" | 0.5° | -55° to 245° | 0000000 | 000000 |
| 4 7/8" | 4 1/2" | Forward/Reverse, Start/Stop | 1 3/16" | 0000000 | 000000 | 5,000 | 4,680 | 0.015" | 0.5° | -55° to 245° | 0000000 | 000000 |
| 5 11/32" | 5" | Forward/Reverse, Start/Stop | 1 3/16" | 0000000 | 000000 | 4,200 | 6,225 | 0.015" | 0.5° | -55° to 245° | 0000000 | 000000 |
Polyurethane Spiders | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
Iron Hubs | Misalignment Capability | |||||||||||
| Overall Lg. | OD | For Motion Type | For Shaft Dia. | Each | Max. Speed, rpm | Max. Torque, in.-lbs. | Parallel | Angular | Temp. Range, °F | Each | ||
| 2 27/32" | 2 35/64" | Forward/Reverse, Start/Stop | 1 3/16" | 0000000 | 000000 | 3,600 | 475 | 0.015" | 1° | -30° to 160° | 0000000 | 000000 |
| 3 31/64" | 2 35/64" | Forward/Reverse, Start/Stop | 1 3/16" | 0000000 | 00000 | 3,600 | 475 | 0.015" | 1° | -30° to 160° | 0000000 | 00000 |
| 4 7/32" | 3 21/64" | Forward/Reverse, Start/Stop | 1 3/16" | 0000000 | 00000 | 3,600 | 1,185 | 0.015" | 1° | -30° to 160° | 0000000 | 000000 |
| 4 1/2" | 3 3/4" | Forward/Reverse, Start/Stop | 1 3/16" | 0000000 | 000000 | 3,600 | 1,860 | 0.015" | 1° | -30° to 160° | 0000000 | 00000 |
Polyurethane Split Spiders | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Iron Hubs | Misalignment Capability | 347 Stainless Steel Retaining Rings | ||||||||||||
| Overall Lg. | OD | For Motion Type | For Shaft Dia. | Each | Max. Speed, rpm | Max. Torque, in.-lbs. | Parallel | Angular | Temp. Range, °F | Each | Each | |||
| 2 27/32" | 2 35/64" | Forward/Reverse, Start/Stop | 1 3/16" | 0000000 | 000000 | 7,700 | 1,110 | 0.03" | 2° | -30° to 200° | 0000000 | 000000 | 0000000 | 000000 |
| 3 31/64" | 2 35/64" | Forward/Reverse, Start/Stop | 1 3/16" | 0000000 | 00000 | 7,700 | 1,110 | 0.03" | 2° | -30° to 200° | 0000000 | 00000 | 0000000 | 00000 |
| 4 7/32" | 3 21/64" | Forward/Reverse, Start/Stop | 1 3/16" | 0000000 | 00000 | 5,900 | 2,180 | 0.03" | 2° | -30° to 200° | 0000000 | 000000 | 0000000 | 00000 |
Lightweight Flexible Shaft Couplings
Made with lightweight nylon sleeves, these gear couplings require less energy to move than other high-torque flexible couplings. They compensate for parallel, angular, and axial misalignment. Fasten to your shafts by tightening the set screws, which bite into the shaft to hold it.
A complete coupling consists of two hubs and one sleeve (each component sold separately).
For technical drawings and 3-D models, click on a part number.
Clamping Shaft Couplings
Designed to grip evenly around your shaft, clamping couplings provide more holding power than set screw couplings without marring the shaft. Slide onto the end of your shaft and tighten the clamping screws to secure. Good for high-torque applications, rigid couplings connect two shafts that are aligned, allowing for no relative movement between the shafts.
Stainless steel couplings have excellent corrosion resistance.
For technical drawings and 3-D models, click on a part number.
| For Shaft Dia. | Overall Lg. | OD | Max. Speed, rpm | Max. Torque, in.-lbs. | For Motion Type | Each | |
Steel | |||||||
|---|---|---|---|---|---|---|---|
For Keyed Shafts | |||||||
| 1 3/16" × 1 3/16" | 3 1/4" | 2 1/16" | 4,000 | 5,000 | Forward/Reverse, Start/Stop, Continuous | 00000000 | 0000000 |
For Round Shafts | |||||||
| 1 3/16" × 1" | 3 1/4" | 2 1/16" | 4,000 | 5,000 | Forward/Reverse, Start/Stop, Continuous | 00000000 | 000000 |
| 1 3/16" × 1 3/16" | 3 1/4" | 2 1/16" | 4,000 | 5,000 | Forward/Reverse, Start/Stop, Continuous | 00000000 | 00000 |
303 Stainless Steel | |||||||
For Keyed Shafts | |||||||
| 1 3/16" × 1 3/16" | 3 1/4" | 2 1/16" | 4,000 | 3,200 | Forward/Reverse, Start/Stop, Continuous | 0000000 | 000000 |
For Round Shafts | |||||||
| 1 3/16" × 1" | 3 1/4" | 2 1/16" | 4,000 | 3,200 | Forward/Reverse, Start/Stop, Continuous | 00000000 | 000000 |
| 1 3/16" × 1 3/16" | 3 1/4" | 2 1/16" | 4,000 | 3,200 | Forward/Reverse, Start/Stop, Continuous | 00000000 | 000000 |
Two-Piece Shaft Coupling Bridges
When your shafts are not close enough to use standard couplings, these have the length to bridge the gap. Install them anywhere on a shaft without removing components or having access to the ends of the shaft. Tighten the clamping screws to secure. Good for high-torque applications, rigid couplings connect two shafts that are aligned, allowing for no relative movement between the shafts.
For technical drawings and 3-D models, click on a part number.
| For Shaft Dia. | Overall Lg. | OD | Max. Speed, rpm | Max. Torque, in.-lbs. | For Motion Type | Each | |
Cast Iron | |||||||
|---|---|---|---|---|---|---|---|
For Keyed Shafts | |||||||
| 1 3/16" | 6 1/4" | 4 1/4" | 5,360 | 2,000 | Forward/Reverse, Start/Stop, Continuous | 0000000 | 0000000 |
Easy-Install Single U-Joints
No drilling required. Steel U-joints connect to shafts using the keyway and included set screws. They have grooves for holding protective boots (not included).
For technical drawings and 3-D models, click on a part number.
For Shaft | Keyway | Torque | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Dia. | Dp. | Joint Dia. | Overall Lg. | Wd. | Dp. | Max. Operating Angle | Max. Speed, rpm | Max. Torque, in.-lbs. | 3° Operating Angle | 10° Operating Angle | Joint Type | Each | |
Steel | |||||||||||||
| 1 3/16" | 1 1/2" | 2" | 5 7/16" | 1/4" | 1/8" | 25° | 1,750 | 15,600 | 2,635 in.-lbs. @ 300 rpm | 885 in.-lbs. @ 300 rpm | Pin and Block | 0000000 | 0000000 |
Torque Limiters for Chain and Belt Drives
Prevent damage from overloading. When overloaded, these limiters cause your sprocket or pulley to slip. Once the overload is removed, the limiters automatically reset. Set the torque within the range listed. Friction discs are between the hub and pressure plate.
Double-spring limiters have a second spring for handling nearly twice the torque of single-spring limiters.
Optional sprockets are designed specifically to fit their corresponding limiters. These hubless sprockets are not interchangeable.
For technical drawings and 3-D models, click on a part number.
Torque Limiters | |||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Keyway | Torque | Optional Sprockets | Replacement Friction Discs for Torque Limiters | Replacement Bushings for Optional Sprockets | |||||||||||||||
| For Shaft Dia. | OD | O'all Wd. | Wd. | Dp. | For Max. Sprocket or Pulley Wd. | Friction Disc Thick. | Min., ft.-lbs. | Max., ft.-lbs. | Hub Material | Each | For Roller Chain Trade Size | Each | Each | For Roller Chain Trade Size | Each | ||||
Single Spring | |||||||||||||||||||
| 1 3/16" | 5" | 2 7/8" | 1/4" | 1/8" | 5/8" | 1/8" | 90 | 250 | Steel | 00000000 | 0000000 | 0000000 | 000000 | 0000000 | 000000 | 000000 | 00000 | ||
Double Spring | |||||||||||||||||||
| 1 3/16" | 5" | 2 7/8" | 1/4" | 1/8" | 5/8" | 1/8" | 120 | 400 | Steel | 00000000 | 000000 | 0000000 | 00000 | 0000000 | 00000 | 000000 | 0000 | ||
| For OD | Each | |
| 5" | 00000000 | 000000 |