These Schedule 40 fittings are the industry standard for gravity-flow drain, waste, and vent (DWV) applications.

Fittings are metal for better durability than plastic barbed hose fittings. They have sharper barbs than standard barbed hose fittings to grip push-on hose without the need for clamps or ferrules. The more you pull on the fittings, the tighter the hose will grip.

Also known as live swivels, these fittings swivel continuously 360° before and after installation. This not only makes installation easier, but also eliminates the twisting and kinking that can cause hose failure. Fittings are threaded on both ends so you can connect them directly to a threaded hose or to pumps, cylinders, and other equipment in your hydraulic system. Use in high-pressure applications up to 5,000 psi.

These two-piece fittings screw directly onto the hose without the need for a separate adapter. When assembled, the fitting compresses against the hose, forming a strong seal. Also known as reusable fittings, they can be unscrewed from the hose end and used on a new hose. Use in high-pressure hydraulic applications up to 5,800 psi.

Use these two-piece fittings in grease and lubrication lines. They screw directly onto hose without the need for a separate adapter. When assembled, the fitting compresses against the hose, forming a strong seal. Also known as reusable fittings, they can be unscrewed from the hose end and used on a new hose.

Use hose to charge and test your air conditioning units.

When cleanliness is crucial to your application, choose these fittings that are individually cleaned and bagged to prevent contamination.

With a nickel-plated finish, these compression fittings resist corrosion better than plain brass fittings.

Create a strong seal on copper tubing when you couple these nuts with compression sleeves and fittings.

These fittings include a nut with a built-in sleeve, so there’s no need to remove the nut for assembly.

No sleeve is required to assemble these fittings, which makes for a faster, more convenient installation compared to 37° flared fittings. They are also known as refrigeration and SAE fittings.

The flared end of the fitting nests inside the fitting body, providing extra support to the tubing. Fittings are also known as inverted 45° flared fittings.

Choose these metal fittings when you need better durability than our plastic push-to-connect fittings.

Create a push-to-connect junction in equipment with these fittings. To install, drill a stepped hole in your surface, push the fitting components into place, then insert your tubing.

Use these fittings to make leak-resistant connections without threading or soldering. Slide them over tubing and turn the end nuts to compress the gasket.

Use these nuts with compression sleeves and fittings to create a strong seal on stainless steel tubing.

Tighten these nuts onto high-pressure compression sleeves and fittings to create a strong seal on stainless steel tubing.

Instead of a metal sleeve (ferrule), these fittings have a rubber sleeve that cushions tubing and absorbs vibration to maintain a tight seal, even when connected to large pumps.

Use these fittings at pressures up to 9,000 psi. Also known as instrumentation fittings, they are made to tight tolerances for use in high-precision applications. They are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings.

For applications that require an extra level of cleanliness, these fittings are individually bagged to prevent contamination.

These fittings have the highest pressure rating of all the Yor-Lok tube fittings we offer.

Individually bagged to prevent contamination, these fittings are suitable for applications that require a high level of cleanliness.

The threads on the tube end of these fittings are Class 3A or 3B and adhere to tighter tolerances than other 37° flared fittings.

Use at pressures up to 4,300 psi.

Butt-weld fittings allow for a smooth, flush connection that provides maximum flow.

The smooth finish inside these stainless steel quick-clamp fittings makes it easy to remove product residue.

Polished to a 20 Ra finish, these fittings have an extra-smooth interior that prevents product buildup and inhibits bacteria growth.

Use these rings with quick-clamp high-vacuum fittings.

The flat face of the fitting connects to a tube adapter so you can slide the tubing and fitting sideways to disconnect in cramped spaces. They are also known zero-clearance fittings.

Fittings are polished to a32 Ra and under finish on the interior.

Fittings have two anti-torque rings that compress the gasket to prevent rotation and reduce particle generation in high-vibration applications.

Create access points in ultra-high-vacuum lines or chambers by bolting two same-size flanges together with a copper gasket between them. The flanges’ sharp edges dig into the copper gasket and form an extremely tight seal, which means they handle higher vacuum pressures than other high-vacuum fittings with rubber gaskets.

An alternative to bolt-together fittings, these handle larger tube OD sizes and have higher vacuum ratings than quick-clamp fittings. Also known as ISO-K high-vacuum fittings, the clamps have claws that grab hold of fittings with flanged ends.

Connect stainless steel tubing on one end and plastic tubing on the other end.

For high-vacuum systems with tube sizes too large for quick-clamp (KF) fittings, choose these bolt-together fittings.

Use these fittings in an air vacuum system to avoid the hassle of brazing and welding. Insert two fittings into a clamp and tighten to form a secure seal in steel tubing.

A single sleeve (ferrule) bites into tubing as you tighten the nut, creating a strong seal.

Use these sleeves with compression nuts and fittings, sometimes called bite fittings, to create a strong seal on steel tubing. They are also known as ferrules.

Pair these nuts with compression sleeves and high-pressure fittings. They withstand about twice as much pressure as nuts for standard compression fittings, so they’re good for hydraulic power applications.

These fittings have two sleeves for extra gripping power. They bite into steel tubing as you tighten the nut to form a strong seal.

Also known as JIS (Japanese Industrial Standard) fittings.

The external hex bolt on these fittings allows for easy installation in cramped spaces. They are also known as banjo-style fittings and JIC (Joint Industrial Council) fittings. They provide a tight seal on tubing that is flared to 37°.

These Monel fittings have the corrosion resistance to handle hydrofluoric and sulfuric acid. Also known as instrumentation fittings, they include a nut with two sleeves.

A built-in shut-off valve stops airflow when the fittings are disconnected from tubing.

Made of brass, these fittings have good corrosion resistance.