With thicker, stronger walls than standard-wall pipe, this Schedule 80 pipe can handle heavy duty industrial plumbing and water supply applications, such as water processing, waste water treatment, and irrigation. It’s made of PVC, which has good corrosion resistance. Pipe meets ASTM D1784 and ASTM D1785 specifications and testing requirements for material quality.

Warning: Never use plastic pipe fittings and pipe with compressed air or gas.

Sealants cannot be sold to Colorado, Connecticut, District of Columbia, Delaware, Illinois, Indiana, Massachusetts, Maryland, Maine, Michigan, New Hampshire, New Jersey, Northern Virginia, New York, Ohio, Pennsylvania, Rhode Island, or Utah due to local VOC (Volatile Organic Compounds) regulations.

For technical drawings and 3-D models, click on a part number.

Also known as Pressure Class 150 flanges, these flanges have thick, strong walls to handle heavy duty industrial plumbing and water supply applications, such as water processing, waste water treatment, and irrigation. They meet NSF/ANSI 61 for drinking water. Bolt two same-size flanges together with a gasket (sold separately) to create an access point within a line. All are PVC, which has good corrosion resistance. They meet ASTM D1784 specifications and testing requirements for material quality.

Warning: Never use plastic pipe flanges and pipe with compressed air or gas.

Sealants cannot be sold to Colorado, Connecticut, District of Columbia, Delaware, Illinois, Indiana, Massachusetts, Maryland, Maine, Michigan, New Hampshire, New Jersey, Northern Virginia, New York, Ohio, Pennsylvania, Rhode Island, or Utah due to local VOC (Volatile Organic Compounds) regulations.

For technical drawings and 3-D models, click on a part number.

Connect this pipe to standard-wall plastic pipe fittings for a variety of residential and commercial low-pressure plumbing and water supply applications. It’s made of PVC, which has good corrosion resistance. Connect to unthreaded female socket-connect fittings using a PVC primer and cement (also known as solvent weld).

Pipe for drinking water meets NSF/ANSI Standard 61.

Pipe that meets ASTM D1784 and ASTM D1785 adheres to specifications and testing requirements for material quality.

Bend radius is the point to which you can bend pipe or tubing without damaging it. The smaller the measurement, the better the bend.

Warning: Never use plastic pipe fittings and pipe with compressed air or gas.

For technical drawings and 3-D models, click on a part number.

Slip these joints over your pipe ends and tighten the band clamps for a secure hold. Joints have a triple-bulb design that provides excellent vibration absorption to reduce stress on your piping system. They also have reinforcing rings for extra support during pressure surges and in vacuum applications.

Neoprene rubber joints are more abrasion resistant than silicone rubber joints.

For technical drawings and 3-D models, click on a part number.

Because the flanges are molded into the body for a wide sealing surface, these joints provide a tighter seal than other expansion joints. Each flange is supported by a zinc-plated steel plate. Flanges mate with a same-size flat-surface Class 150 flange without the need for a gasket. Joints reduce stress, vibration, and noise in metal piping systems by providing a point of flexibility to absorb movement. They have a flexible body that is reinforced with cord for added strength.

For technical drawings and 3-D models, click on a part number.

These all-metal expansion joints can handle higher temperatures than rubber expansion joints. They reduce stress, vibration, and noise in piping systems by providing a point of flexibility to absorb movement. Joints are made of 304 stainless steel for very good corrosion resistance. The flanged ends rotate for easy bolt hole alignment during installation. Flanges mate with a same-size flat-surface Class 150 flange with a gasket (sold separately).

Liners (sold separately) slide into the expansion joint to provide a smooth interior for unrestricted flow.

For technical drawings and 3-D models, click on a part number.

A complete coupling consists of a plug and a socket (both sold separately) that allow you to quickly connect and disconnect medium-to large-diameter hose lines. To connect, insert the plug into the socket and press the levers down. The levers fit snugly into the groove on the plug’s body and force the plug against the gasket to form a tight seal. To disconnect, lift both levers and pull out the plug.

Plugs with male threaded end are also known as F adapters.

Plugs with female threaded end are also known as A adapters.

Couplings with locking levers prevent accidental disconnection. The locks engage automatically when the coupling is connected. Press the locks simultaneously to disengage.

Sockets with male threaded end are also known as B couplers.

Straight sockets with female threaded end are also known as D couplers.

Aluminum couplings are lighter in weight than brass plugs and sockets. They have good abrasion and corrosion resistance. Brass couplings are softer than aluminum plugs and sockets, so they’re easier to thread together. They have good corrosion resistance.

Note: To ensure a correct fit, make sure that the plug and socket have the same coupling size.

Warning: Relieve all pressure before disconnecting the couplings. Do not use cam-and-groove couplings with compressed air or gas.

For technical drawings and 3-D models, click on a part number.

Low-profile barbs and a longer first barb allow for a smoother, easier installation than other barbed fittings. Slide the barbed end into rubber hose and secure with a clamp.

Steel fittings are stronger and more durable than other metal fittings. They should be used in noncorrosive environments. Zinc-plated steel fittings have slightly better corrosion resistance than unplated steel fittings. Fittings with a threaded end are also known as hose nipples.

For technical drawings and 3-D models, click on a part number.

Made of metal, these couplings have better durability than plastic cam-and-groove couplings. A complete coupling consists of a plug and a socket (both sold separately) that allow you to quickly connect and disconnect medium-to large-diameter hose lines. To connect, insert the plug into the socket and press the levers down. The levers fit snugly into the groove on the plug’s body and force the plug against the gasket to form a tight seal. To disconnect, lift both levers and pull out the plug. Couplings are compatible with Andrews, Dixon, Ever-Tite, and PT cam-and-groove couplings.

Plugs with male threaded end are also known as F adapters.

Plugs with female threaded end are also known as A adapters.

Sockets with locking levers prevent accidental disconnection. The locks engage automatically when the coupling is connected. Press the locks simultaneously to disengage.

Sockets with male threaded end are also known as B couplers.

Straight sockets with female threaded end are also known as D couplers.

Aluminum plugs and sockets are lighter in weight than 316 stainless steel plugs and sockets. They have good corrosion resistance. 316 stainless steel plugs and sockets have excellent corrosion resistance.

Note: To ensure a correct fit, make sure that the plug and socket have the same coupling size.

Warning: Relieve all pressure before disconnecting the couplings. Do not use cam-and-groove couplings with compressed air or gas.

For technical drawings and 3-D models, click on a part number.

Low-profile barbs and a longer first barb allow for a smoother, easier installation than other barbed fittings. Slide the barbed end into rubber hose and secure with a clamp. Fittings are 316 stainless steel, which has excellent corrosion resistance to withstand a variety of chemicals.

Adapters are also known as hose nipples; they adapt a barbed end to a threaded end.

For technical drawings and 3-D models, click on a part number.