Pair these holders with a tool block for right- and left-hand mounting in a lathe.

Mount blade-style holders to a lathe tool post or turret.

Cut square corner grooves in a workpiece or cut completely through a part.

Also known as parting blades, use these to separate a finished part from the workpiece.

The carbide tip brazed onto these blades is more wear resistant than high-speed steel.

Also known as jeweler's slotting saws and metal slitting saws, these saws are good for use on wire, tubing, extrusions, and other very thin material that requires delicate cuts.

With peripheral and side teeth, these saws remove chips for a consistent cutting width.

A higher air consumption rating allows this saw to work in longer bursts than the light duty air-powered portable cutoff saw. It has a durable composite handle.

Use abrasive wheels with this saw to cut through hard materials.

Make fast cuts through tough metal, such as angle iron and flat bar, with more than twice the horsepower of bench-top cutoff saws. These saws must be hardwired.

Pins hold hose slightly bent, pulling it apart as the knife-edge blade slices a straight, smooth cut.

Two layers of fiberglass mesh reinforcement give these wheels at least three times the life of standard cutoff wheels when cutting metal such as aluminum, iron, stainless steel, and steel.

Run these high-density aluminum oxide wheels at higher speeds than standard cutoff wheels to make quick cuts in aluminum, iron, stainless steel, and steel.

Use these clog-resistant zirconia alumina wheels to make quick cuts in soft metal such as aluminum, brass, and copper.

Also known as Type 27, raised-hub, and depressed-center cutoff wheels, these wheels outperform Type 1 wheels when making flush cuts in aluminum, iron, stainless steel, and steel.

Made of premium grade abrasives, these wheels are strong and thick for making notches in aluminum, iron, stainless steel, and steel.

Also known as Type 27, raised-hub, and depressed-center cutoff wheels, these wheels outperform Type 1 wheels when making flush cuts.

Also known as Type 27, raised-hub, and depressed-center cutoff wheels, these wheels outperform Type 1 wheels when making flush cuts.

Made of a combination of ceramic alumina and zirconia alumina, these wheels last up to ten times longer than standard cutoff wheels when cutting hard metal such as Inconel, Hastelloy, and tool steel.

These steel wheels have a diamond grit edge, so they last longer than standard bench-grinder cutoff wheels when cutting hard, nonferrous materials such as carbide, ceramics, and glass.

A ceramic alumina abrasive cuts through stainless steel.

Use these wheels for cutting soft metal, plastic, stone, and wood.

Two layers of fiberglass mesh reinforcement give these fast-cutting, zirconia alumina wheels at least three times the life of standard cutoff wheels when aluminum, iron, stainless steel, and steel.

Make cuts in hard, brittle materials such as firebrick, stone, and concrete.

These wheels are designed to cut stainless steel. They are reinforced with a layer fiberglass mesh.

These wheels are reinforced with fiberglass mesh and designed to last longer than standard wheels when cutting ductile cast iron.

Make fast, burr-free cuts in stainless steel with these premium aluminum oxide wheels.

Designed to cut sheet metal.

These wheels have a blend of aluminum oxide and silicon carbide abrasives for cutting ductile cast iron.

Make cuts in most metal, including aluminum, iron, stainless steel, and steel.

The segmented edge on these blades is coated with diamond grit for cutting plastic.

A tungsten carbide grit edge cuts through abrasive materials such as composites and fiberglass.

Square-shaped teeth cut across the grain and with the grain (ripping) in reclaimed lumber and flooring with embedded nails.

Also known as dado-head blades, these are for cutting grooves in all types of wood.

Cut wood, plywood, and particleboard.

A continuous edge on these blades produces smooth cuts. It's coated in diamond grit to cut hard, abrasive materials such as masonry, stone, asphalt, and concrete.

A blend of tungsten carbide and diamond grits on the continuous edge of these blades cuts hard, nonmetallic materials including composites and graphite.

The carbide-grit edge on these blades cuts brittle and abrasive materials including glass and fiberglass.

The edge of the blade is segmented to cut faster than a continuous edge.

Diamond grit bonded to a segmented edge cuts through hard metal such as cast iron.

Teeth are carbide tipped and designed to push chips away from the blade to prevent clogging and produce smooth cuts in aluminum sheets, tubing, and T-slotted framing.

Blades and teeth are steel and treated to a Rockwell Hardness between C63 and C65 for increased wear resistance when cutting through steel and cast iron bars, rods, pipe, and tubing.

Make fast, clean cuts in steel sheets, angle iron, rebar, and pipe with the carbide teeth on these blades.

Prevent clogging when cutting soft metal—these blades have plenty of space between the carbide-tipped teeth to allow chips to escape.

These blades have a higher concentration of diamonds than other dry-cutting blades, so they last up to three times longer.

The edge of the blade is segmented to cut faster than a continuous edge.

Use with water or coolant to produce smoother cuts in tile than dry-cutting blades. They're also for use on glass.

A continuous edge on these blades produces smooth cuts.

Produce smooth cuts in plastic materials including polycarbonate, polyurethane, PVC, and acrylic with the carbide-tipped teeth on these blades.

Use these blades for occasional cutting.

Cut wood, plywood, and particleboard.

A blend of tungsten carbide and diamond grits on the continuous edge of this blade cuts hard, nonmetallic materials including composites and graphite.

Make clean cuts in rubber and plastic hose with the scalloped knife edge on these blades.