Made of premium grade abrasives, these wheels are strong and thick for making notches in aluminum, iron, stainless steel, and steel. They’re reinforced with two layers of fiberglass mesh. Also known as Type 27, raised-hub, and depressed-center cutoff wheels, they outperform Type 1 wheels when making flush cuts.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

For technical drawings and 3-D models, click on a part number.

Switch between cutting and deburring aluminum, iron, stainless steel, and steel without the need to change your wheel. Three layers of fiberglass mesh reinforce these aluminum oxide wheels. They're also known as Type 27, raised-hub, and depressed-center cutoff wheels, and they outperform Type 1 wheels when making flush cuts.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

For technical drawings and 3-D models, click on a part number.

Also known as Type 27, raised-hub, and depressed-center cutoff wheels, these wheels outperform Type 1 wheels when making flush cuts. They make fast, burr-free cuts in stainless steel. Wheels are reinforced with two layers of fiberglass mesh. Choose coarser grit for fast cuts; choose finer grit for smooth cuts.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

For technical drawings and 3-D models, click on a part number.

Made of premium grade of abrasives, these wheels are strong and thick for making notches in stainless steel. They’re reinforced with two layers of fiberglass mesh. Also known as Type 27, raised-hub, and depressed-center cutoff wheels, these wheels outperform Type 1 wheels when making flush cuts.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

For technical drawings and 3-D models, click on a part number.

Made of ceramic alumina or a combination of ceramic alumina and zirconia alumina, these wheels last up to ten times longer than standard cutoff wheels when cutting hard metal such as Inconel, Hastelloy, and tool steel. Wheels are reinforced with two layers of fiberglass mesh.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

For technical drawings and 3-D models, click on a part number.

Made of ceramic alumina, these wheels last 10 times longer than standard cutoff wheels when cutting hard metal, such as tool steel. They’re reinforced with two layers of fiberglass mesh. These wheels, also known as Type 27, raised hub, and depressed-center cutoff wheels, outperform Type 1 wheels when making flush cuts.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

For technical drawings and 3-D models, click on a part number.

Ideal when working across multiple materials, these wheels are specially constructed to cut plastic, fiberglass, concrete, and ceramic, as well as metal. They also work with sheet metal. They contain less than 0.1% iron, chloride, and sulfur contaminants to prevent corroding and discoloring stainless steel and other nickel-alloyed steel.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

For technical drawings and 3-D models, click on a part number.

Also known as Type 27, raised-hub, and depressed-center cutoff wheels, these wheels outperform Type 1 wheels when making flush cuts. They make quick cuts in soft metal such as aluminum, brass and copper without clogging. Wheels are reinforced with two layers of fiberglass mesh.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

For technical drawings and 3-D models, click on a part number.

Make cuts in hard, brittle materials such as firebrick, stone, and concrete. Wheels are made of silicon carbide abrasive that is reinforced with a layer of fiberglass mesh.

Type 27 cutoff wheels outperform Type 1 wheels when making flush cuts. Also known as raised-hub and depressed-center cutoff wheels.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

For technical drawings and 3-D models, click on a part number.

Use these wheels to cut through metal such as iron, stainless steel, and steel. They are reinforced with a layer of fiberglass mesh. Choose coarser grit for fast cuts; choose finer grit for smooth cuts.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

For technical drawings and 3-D models, click on a part number.

Run these high-density aluminum oxide wheels at higher speeds than standard cutoff wheels to make quick cuts in aluminum, iron, stainless steel, and steel. Wheels are reinforced with a layer of fiberglass mesh.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

For technical drawings and 3-D models, click on a part number.

These high-density ceramic or ceramic oxide wheels have two layers of fiberglass mesh reinforcement and last up to twice as long as long-life cutoff wheels when cutting iron, stainless steel, and steel.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

For technical drawings and 3-D models, click on a part number.

The edge of the blade is segmented to cut faster than a continuous edge. These blades have diamond grit that lasts up to three times longer than the grit on other blades for masonry and stone in continuous use applications on hard, abrasive materials. Use dry or with water or coolant (not included). Blades come with a reducer bushing to adjust the arbor diameter.

For technical drawings and 3-D models, click on a part number.

A continuous edge on these blades produces smooth cuts. They have diamond grit that lasts up to three times longer than the grit on other blades for masonry and stone in continuous use applications on hard, abrasive materials. Use dry or with water or coolant (not included). Blades come with a reducer bushing to adjust the arbor diameter.

For technical drawings and 3-D models, click on a part number.

A continuous edge on these blades produces smooth cuts. It's coated in diamond grit to cut hard, abrasive materials such as masonry, stone, asphalt, and concrete. Use dry or with water or coolant (not included). Blades come with a reducer bushing to adjust the arbor diameter.

The edge of the blade is segmented to cut faster than a continuous edge. It's coated in diamond grit to cut hard, abrasive materials such as masonry, stone, asphalt, and concrete. Use dry or with water or coolant (not included). Blades come with a reducer bushing to adjust the arbor diameter.

For technical drawings and 3-D models, click on a part number.

A continuous edge coated in diamond grit makes fast, smooth cuts in stone and ceramic tile. Blades with multiple arbor diameters come with a reducer bushing.

For technical drawings and 3-D models, click on a part number.