These lights fit into ceiling cutouts.

Mount these fixtures where you need light but don't have an electrical connection. They automatically turn on when movement is detected and off when an area is unoccupied.

Also known as pigtail holders. Temporarily wire these sockets to provide light during construction.

Use these lights in large, open areas such as warehouses and manufacturing spaces where the ceiling is up to 30-ft. high.

These lights produce a wide beam of uniform light to fill large, open areas with ceilings up to 18-ft. high.

Suspend or mount with fasteners to the ceiling.

Mount these lights flush with ceilings in wet locations—all are sealed to keep out humidity and dripping, splashing, and falling liquids. Unlike recessed can lights, which require a separate housing, these fit directly into a cutout in your ceiling and are held in place by springs.

A wraparound lens disperses light from the sides as well as the bottom to produce ambient lighting.

A flexible design allows these lights to be suspended above, wrapped around, or routed through areas on the job site.

With a NEMA 4X rating, these lights resist degradation when exposed to corrosive liquids, withstand liquids sprayed during washdowns, and are dust tight.

The handle on this floodlight also acts as a stand—pivot it 360° to aim light where it's needed. This floodlight is small and easy to carry to job sites that don't have electrical power.

Rated IP65, these lights are sealed to protect against light washdowns from a garden hose. They have a height-adjustable stand and light heads that pivot up and down to direct light where it's needed.

Shine light into hard-to-reach spaces with these flexible-arm flashlights.

Made of stainless steel, these pocket-size flashlights have a smooth, easy-to-clean surface.

Always have a flashlight on hand—these attach to a key ring.

Small enough to keep in your shirt pocket, these penlights are rated for use in environments where hazardous material is present.

In addition to pivoting 210°, the light heads rotate 360° for directing light exactly where it’s needed. They're rated for use in environments where hazardous material is present.

All of these flashlights stand up to wet environments.

Keep your hands free by wearing a flashlight on your head.

Shine light on machinery and through the sight glass on tanks to inspect food, brewery, chemical, pharmaceutical, and bio-tech processing lines.

Mount these lights near entry doors, loading areas, and driveways to cast an even glow of light.

Powered by the sun, these security lights function in areas that don’t have access to electricity. They’re often used to shine light on parking lots, landscaping, signs, entryways, and other outdoor spaces.

These lights are UL listed for use in hazardous locations where flammable/combustible gases, vapors, and liquids may be present.

Heads adjust to any angle to direct light where needed.

Hardwire these lights to a power source.

These classic-style machine lights have a reflector to distribute light more evenly than strip machine lights.

A sealed head and switch keeps these lights shining in wet environments. They swing out from the wall and adjust horizontally and vertically to illuminate loading dock and trailers.

Rated for use in damp locations, these lights withstand humidity and moisture.

Rated NEMA 4X, these lights are protected from corrosion and washdowns.

Rated NEMA 4X and 13 for protection from dirt, washdowns, corrosion, and oil/coolant spraying.

Direct your signal with these lights; they flash in one direction.

The pad below the base absorbs shock and vibration.

Carry these lights around with you and place them wherever needed. They can switch between being continuous or flashing.

A series of four flashes per cycle makes these lights more visible than other strobe lights.

Set these portable lights wherever you need a signal light—they don't need to be wired or plugged in.

These lights have lenses that snap in and out, so you can easily swap colors or change their position in the stack.

Design a stack light with your choice of light pattern and color. Start with a base, then add up to five modules total—twist and lock them together.

Use these lights in tight spaces in place of a tower. They emit three colors from a single lens.

The quick-connect four-pole M12 plug on these lights makes them easy to hook up and configure.

Good for tight spaces where a tower of lights won't fit, these emit three colors from a single lens.