A titanium aluminum nitride (TiAlN) coating provides heat and wear resistance for longer life.

Bend around obstructions to access hard-to-reach spots.

Diamond-cut teeth effectively cut hard materials.

Power troublesome burrs off of thin-wall (EMT) conduit and attach fittings in less time than traditional hand tools. These bits have a 1/4" hex shank that fits quick-change drill chucks and power screwdrivers to quickly deburr the inside and outside edges of conduit in a single step.

Place the tool over your tube and twist to deburr.

These drill attachments scrape both the inner and outer edges of plastic pipe and tube to finish them for connections.

Carry these slim-handled tools comfortably in your pocket.

Also known as machinist's scrapers, these tools remove material and smooth edges on a workpiece.

These blades are titanium nitride (TiN) coated for wear resistance.

These blades are titanium nitride (TiN) coated for wear resistance.

Extend your reach with these 6 1/4" to 7" long burs.

These sets include four handles and four blades.

A ratcheting handle saves space when smoothing the edge of tubes and holes. With short, repeatable turns, these scrapers deburr with greater speed and precision than standard scrapers.

Use with blades that have a 0.1" shank and trade numbers with a prefix of B.

Carry these slim-handled tools comfortably in your pocket.

Colored handles make these tools easy to see and keep organized.

Sand inside pipes and tubes as well as on an angle to reach into corners and slots.

Assortments include a selection of flap wheels to polish, clean, and debur deep inside tubes and cylinders.

To create a clean, smooth finish on your material, these countersinks have specially designed spiral flutes that reduce chip buildup on the cutting edge.

Often used to cut hard and abrasive materials, these carbide countersinks are harder, stronger, and more wear resistant than cobalt steel and high-speed steel countersinks.

More heat and abrasion resistant than high-speed steel, cobalt steel has better performance on hard-to-machine materials.

Specially designed with spiral flutes that reduce chip buildup on the cutting edge, these countersinks produce a clean, smooth finish on your material.

Harder, stronger, and more wear resistant than high-speed steel countersinks, these are carbide for better performance on hard and abrasive materials.

These highly accurate countersinks have a tolerance of 0" to +0.001", so you can use them with computer-controlled machines.

These carbide countersinks are harder, stronger, and more wear resistant than high-speed steel for better performance on hard and abrasive materials.

An 82° countersink angle is compatible with the profile of flat- and oval-head inch screws; a 90° countersink angle is compatible with the profile of flat- and oval-head metric screws and is also good for deburring.

An 82° countersink angle is compatible with the profile of flat- and oval-head inch screws; a 90° countersink angle is compatible with the profile of flat- and oval-head metric screws and is also good for deburring.

The 100° countersink angle is compatible with the profile of rivets.

An angled hole passes through the center of these countersinks to reduce vibration and chatter, creating smooth cuts and preventing chips from clogging the tool.

The built-in pilot maintains alignment in the hole.

To create smooth cuts and prevent chips from clogging the tool, these countersinks have an angled hole that passes through the center of the tool for reduced vibration and chatter.

The 82° countersink angle is compatible with the profile of flat- and oval-head inch screws.

For general purpose use.

To remove the need for a starter hole, the drill point is incorporated into the countersink flutes.

An angled hole passes through the center of the countersinks in these sets to reduce vibration and chatter, which creates clean cuts and prevents chips from clogging the tool.

Choose countersinks of different sizes from these sets. Compared to countersinks with round shanks, these 1/4" hex-shank countersinks can be gripped more tightly by compatible drills and screwdrivers for greater torque.

For general purpose use.

Carbide is harder, stronger, and more wear resistant than high-speed steel for better performance on hard and abrasive materials.

The built-in pilot maintains alignment in the hole.

Choose these countersinks for general purpose applications.

To create a smooth, clean finish on your material, these countersinks have specially designed spiral flutes that reduce chip buildup on the cutting edge.

Magnets on the hex nut hold the reamer in place in your tool and prevent it from accidentally falling.

Use these reamers in stationary machines.

Correct hole misalignment when working in confined spaces. About 2" shorter than standard hole-alignment reamers of similar thicknesses, these reamers give you extra room to move when there’s limited space between you and your workpiece.

The hex nut on the end of the shank lets you use these reamers with square-drive impact wrench sockets.

Smooth and expand hole diameters that are 1 ¾" and larger with these reamers.