Guide air toward your workspace or deflect unwanted drafts with these diverters and covers.

Place these diffusers in the grid of a drop ceiling to distribute air evenly throughout your space.

These dampers regulate airflow.

A vapor barrier provides moisture protection as these diffusers spread hot or cold air around a room.

Evenly disperse airflow into a room to maintain a consistent temperature throughout the space.

Place these grilles in the grid of a drop ceiling.

Add a filter to these grilles for protection against dust and debris entering your HVAC system.

No need for clamps or connectors—duct and fittings have a male end that is slightly smaller than its female end for simple assembly.

Always open, these are our most basic wall louvers.

Mount these louvers into openings that are too small for most louvers. They are sized for use in block and brick walls.

Get an exact fit for your opening by sliding out these louvers to the width you need.

Thicker than standard movable-blade wall louvers, these are rugged and dependable.

Use these louvers in harsh environments—they won't rust.

Allow air to circulate through doors while maintaining privacy.

Cover chimneys to reduce downdrafts and prevent obstructions from entering.

Keep rain and debris out of vertical exhaust pipe with these caps that open with slight pressure from exhaust.

Commonly used with high-flow, air-powered equipment, such as diaphragm pumps and valves, these mufflers reduce noise and filter exhaust fumes without restricting flow.

A small hex size makes these high-flow mufflers a great fit for cramped spaces.

Adjust flow by turning the screw, then tighten the hex nut with a wrench to secure.

These mufflers can be cleaned for an extended service life.

Also known as reclassifiers, these mufflers have a clear reservoir with a drain plug to remove and store oil mist for reuse.

Install these mufflers in air-powered drills and other loud equipment. They filter exhaust fumes and reduce noise by 30-35 dB, a reduction that's equivalent to putting in earplugs.

Mount near a machine to deflect debris away from the immediate area. Guards swing in and out as needed.

Provide excellent chemical resistance with these silica cloth curtains.

The aluminum on one side of these curtains reflects radiant heat.

These curtains are for intermittent contact with flames and hot surfaces.

Shield workers while allowing them to see and be seen.

Cut with scissors to create custom curtains—they have grommets and are ready to hang.

Combine straight and curved sections to build a hanging one- to four-sided curtain partition.

Lightweight and flexible enough to roll up and carry, these panels are wire reinforced so they stand on their own.

Everything you need to build a four-sided curtain partition.

Cut with scissors to create custom curtains—they have grommets and are ready to hang. A vinyl coating provides oil resistance.

Lightweight and flexible enough to roll up and carry, these panels are wire reinforced so they stand on their own. A vinyl coating provides oil resistance.

The vinyl coating on these curtains withstands oil.

Shield workers while allowing them to see and be seen.

With an easy-to-see frame and clear panels, these partitions let you safely establish sections or distance between people in your workspace.

Create a barrier between customers and employees to stop the spread of illness.

Shield forklift operators from rain, snow, wind, and dust while keeping a clear, unobstructed view for safety. These covers are sized to fit most forklift cabs.

A universal mounting bracket adapts to fit most equipment.

Protect work areas and equipment from overhead leaks with these rot- and chemical-resistant tarps.

These panels lift on and off their posts in seconds, so you can protect machinery while providing access for maintenance.

Combine posts, panels, and doors to create a barrier around equipment.

Commonly used in offices, hospitals, and schools, these guards protect corners on walls and other surfaces from impact.

Protect walls and other surfaces from impact.

Even in the dark, these black and yellow striped guards draw attention to equipment and obstructions. They protect corners on walls, posts, shelving, and other surfaces from damage.

The raised bulb adds cushioning to absorb more impact than other corner guards to protect corners on walls, cabinets, and other surfaces from impact.

Combine corner guards, surface guards, and end caps to create a system that protects walls and equipment from impact and wear. Often used in offices, hospitals, and schools, these systems protect against damage from small carts and chairs.

Connect two panels while protecting the edges from damage.

Black and yellow stripes create a visual alert to draw attention to equipment and obstructions. Designed to cushion during impact, this foam trim protects edges on posts, shelving, and other surfaces from damage.

Safeguard pipe, tubing, and other round equipment from damage. Black and yellow stripes create a visual alert to draw attention to equipment and obstructions.

Commonly used on stair rails, vehicle panels, and heavy equipment, this durable rubber film is tear resistant. Use it to protect metal, wood, plastic, composite, and painted surfaces from damage.

A metal core adds strength and stability, making this trim more durable than other high-temperature rubber trim. It withstands temperatures up to 400° F, which is generally twice as high as our standard rubber trim. Use it to protect the edges of panels, boards, and signs from impact. Made of rubber, it resists abrasion better than plastic trim.

Reinforce the edge of a door to guard it against damage from foot traffic and equipment. These plates can also be used to salvage rusted, rotted, or otherwise damaged doors.

Often used to protect sheet metal during fiber and CO2 laser cutting, this film is also good for other fabrication processes such as bending, stamping, and forming. You can even leave this film on finished parts for protection against damage during shipping and storage.

This trim meets FMVSS-302 for Federal Motor Vehicle Safety Standards for flammability, UL 94HB flame requirements, and NFPA (National Fire Protection Agency) standards. Made of plastic, it's also chemical resistant. Use it to protect the edges of panels, boards, and signs from impact.

Made of woven polyethylene fabric, this is the most puncture-, abrasion-, and tear-resistant surface protection we offer. Commonly used on heavy equipment, it guards metal, plastic, composite, and painted surfaces from damage. It can also be used as a protective layer beneath other materials.

Also known as door plates, armor plates, and mop plates, kick plates protect the base of a door from damage caused by foot traffic and equipment.

Easily attach, move, and replace these magnetic wear strips on metal surfaces to minimize friction—simply press them on and peel them off as needed. Often found on conveyor systems and chutes, use these strips where friction between two parts or materials is wearing down equipment to extend equipment life.

Cushioning on the top provides added protection from impact. This nylon-coated stainless steel trim combines strength with flexibility for a snug hold. It can also protect wire, cable, and hose.

A metal core adds strength and stability, making this trim more durable than standard rubber trim. Made of rubber, it resists abrasion better than plastic trim. Use it to protect the edges of panels, boards, signs, and mirrors from impact.