Mount Type Mount Type |
---|
|
Head End Height Head End Height |
---|
|
|
|
Overall Height Overall Height |
---|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
---|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
---|
|
Shoulder Diameter Shoulder Diameter |
---|
|
|
Head Diameter Head Diameter |
---|

For Use On For Use On |
---|
|
|
Head Length Head Length |
---|

Locating Pins

Install these pins in a plate or table and mate with holes in a workpiece for precise alignment. Press the shank into a drilled hole for permanent installation.
Diamond-head pins make less contact with the inside of a hole than round-head pins to reduce sticking and jamming.
For technical drawings and 3-D models, click on a part number.
Head | Tolerance | ||||||||
---|---|---|---|---|---|---|---|---|---|
Dia. (A) | Ht. (B) | Shank Dia. (C) | O'all Ht. | Head Dia. | Shank Dia. | Material | Hardness | Each | |
Diamond Head | |||||||||
7/32" | 11/32" | 3/16" | 3/4" | -0.001" to -0.0007" | 0.0001" to 0.0003" | Steel | Rockwell C60 | 0000000 | 000000 |
1/4" | 11/32" | 3/16" | 3/4" | -0.001" to -0.0007" | 0.0001" to 0.0003" | Steel | Rockwell C60 | 0000000 | 0000 |
9/32" | 13/32" | 1/4" | 7/8" | -0.001" to -0.0007" | 0.0001" to 0.0003" | Steel | Rockwell C60 | 0000000 | 00000 |
5/16" | 13/32" | 1/4" | 7/8" | -0.001" to -0.0007" | 0.0001" to 0.0003" | Steel | Rockwell C60 | 0000000 | 0000 |
11/32" | 1/2" | 5/16" | 1" | -0.001" to -0.0007" | 0.0001" to 0.0003" | Steel | Rockwell C60 | 0000000 | 00000 |
3/8" | 1/2" | 5/16" | 1" | -0.001" to -0.0007" | 0.0001" to 0.0003" | Steel | Rockwell C60 | 0000000 | 0000 |
13/32" | 19/32" | 3/8" | 1 1/4" | -0.001" to -0.0007" | 0.0001" to 0.0003" | Steel | Rockwell C60 | 0000000 | 00000 |
7/16" | 19/32" | 3/8" | 1 1/4" | -0.001" to -0.0007" | 0.0001" to 0.0003" | Steel | Rockwell C60 | 0000000 | 0000 |
15/32" | 21/32" | 7/16" | 1 3/8" | -0.001" to -0.0007" | 0.0001" to 0.0003" | Steel | Rockwell C60 | 0000000 | 00000 |
1/2" | 21/32" | 7/16" | 1 3/8" | -0.001" to -0.0007" | 0.0001" to 0.0003" | Steel | Rockwell C60 | 0000000 | 0000 |
9/16" | 3/4" | 1/2" | 1 1/2" | -0.0015" to -0.001" | 0.0001" to 0.0003" | Steel | Rockwell C60 | 0000000 | 0000 |
5/8" | 27/32" | 9/16" | 1 3/4" | -0.0015" to -0.001" | 0.0001" to 0.0003" | Steel | Rockwell C60 | 0000000 | 0000 |
11/16" | 29/32" | 5/8" | 2" | -0.0015" to -0.001" | 0.0001" to 0.0003" | Steel | Rockwell C60 | 0000000 | 00000 |
3/4" | 1" | 11/16" | 2 1/8" | -0.0015" to -0.001" | 0.0005" to 0.001" | Steel | Rockwell C60 | 0000000 | 00000 |
13/16" | 1 3/32" | 3/4" | 2 1/4" | -0.0015" to -0.001" | 0.0005" to 0.001" | Steel | Rockwell C60 | 0000000 | 00000 |
7/8" | 1 5/32" | 13/16" | 2 1/2" | -0.0015" to -0.001" | 0.0005" to 0.001" | Steel | Rockwell C60 | 0000000 | 00000 |
15/16" | 1 1/4" | 7/8" | 2 3/4" | -0.0015" to -0.001" | 0.0005" to 0.001" | Steel | Rockwell C60 | 0000000 | 00000 |
1" | 1 5/16" | 15/16" | 2 7/8" | -0.0028" to -0.002" | 0.0005" to 0.001" | Steel | Rockwell C60 | 0000000 | 00000 |
1 1/8" | 1 1/2" | 1" | 3 1/4" | -0.0028" to -0.002" | 0.0005" to 0.001" | Steel | Rockwell C60 | 0000000 | 00000 |
1 1/4" | 1 11/16" | 1 1/8" | 3 5/8" | -0.0028" to -0.002" | 0.0005" to 0.001" | Steel | Rockwell C60 | 0000000 | 00000 |
1 3/8" | 1 13/16" | 1 1/4" | 4" | -0.0028" to -0.002" | 0.0005" to 0.001" | Steel | Rockwell C60 | 0000000 | 00000 |
1 1/2" | 2" | 1 3/8" | 4 1/4" | -0.0028" to -0.002" | 0.0005" to 0.001" | Steel | Rockwell C60 | 0000000 | 00000 |
1 5/8" | 2 3/16" | 1 1/2" | 4 5/8" | -0.0028" to -0.002" | 0.0005" to 0.001" | Steel | Rockwell C60 | 0000000 | 00000 |
1 3/4" | 2 5/16" | 1 5/8" | 5" | -0.0028" to -0.002" | 0.0005" to 0.001" | Steel | Rockwell C60 | 0000000 | 00000 |
1 7/8" | 2 1/2" | 1 3/4" | 5 1/4" | -0.0028" to -0.002" | 0.0005" to 0.001" | Steel | Rockwell C60 | 0000000 | 00000 |
2" | 2 11/16" | 1 7/8" | 5 1/2" | -0.0028" to -0.002" | 0.0005" to 0.001" | Steel | Rockwell C60 | 0000000 | 00000 |
Head | Tolerance | |||||||||
---|---|---|---|---|---|---|---|---|---|---|
Dia. (A), mm | Ht. (B), mm | Shank Dia. (C), mm | O'all Ht., mm | Head Dia., mm | Shank Dia., mm | Material | Hardness | Specifications Met | Each | |
Diamond Head | ||||||||||
6 | 7 | 4 | 13 | -0.012 to -0.004 | 0.008 to 0.016 | Steel | Rockwell C54 | DIN 6321 | 00000000 | 000000 |
8 | 10 | 6 | 19 | -0.014 to -0.005 | 0.008 to 0.016 | Steel | Rockwell C54 | DIN 6321 | 00000000 | 00000 |
10 | 10 | 6 | 19 | -0.014 to -0.005 | 0.008 to 0.016 | Steel | Rockwell C54 | DIN 6321 | 00000000 | 00000 |
12 | 10 | 6 | 19 | -0.017 to -0.006 | 0.008 to 0.016 | Steel | Rockwell C54 | DIN 6321 | 00000000 | 00000 |
16 | 13 | 8 | 25 | -0.017 to -0.006 | 0.01 to 0.019 | Steel | Rockwell C54 | DIN 6321 | 00000000 | 00000 |
20 | 15 | 12 | 33 | -0.02 to -0.007 | 0.012 to 0.023 | Steel | Rockwell C54 | DIN 6321 | 00000000 | 00000 |
25 | 15 | 12 | 33 | -0.02 to -0.007 | 0.012 to 0.023 | Steel | Rockwell C54 | DIN 6321 | 00000000 | 00000 |
Mating Locating Pins and Hole Liners


Maintain consistent alignment in mating parts by installing a pin in one part and a liner in the other. These components press into place for permanent installation.
For technical drawings and 3-D models, click on a part number.
Head | Shank | Shoulder | Tolerance | |||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Dia. (A) | Ht. (B) | Dia. (C) | Ht. (D) | Dia. | Ht. | O'all Ht. | Head Dia. | Shank Dia. | Material | Hardness | Each | |
Diamond Head | ||||||||||||
1/4" | 0.219" | 13/32" | 3/8" | 0.563" | 0.063" | 0.656" | -0.0004" to -0.0001" | 0.0014" to 0.0017" | Steel | Rockwell C50 | 00000000 | 000000 |
5/16" | 0.281" | 1/2" | 3/8" | 0.625" | 0.063" | 0.719" | -0.0004" to -0.0001" | 0.0014" to 0.0017" | Steel | Rockwell C50 | 00000000 | 00000 |
3/8" | 0.313" | 5/8" | 1/2" | 0.750" | 0.063" | 0.875" | -0.0005" to -0.0002" | 0.0014" to 0.0017" | Steel | Rockwell C50 | 00000000 | 00000 |
1/2" | 0.406" | 3/4" | 1/2" | 0.875" | 0.063" | 0.969" | -0.0005" to -0.0002" | 0.0015" to 0.0018" | Steel | Rockwell C50 | 00000000 | 00000 |
5/8" | 0.438" | 7/8" | 1/2" | 1.000" | 0.125" | 1.063" | -0.0005" to -0.0002" | 0.0015" to 0.0018" | Steel | Rockwell C50 | 00000000 | 00000 |
3/4" | 0.563" | 1" | 3/4" | 1.125" | 0.125" | 1.438" | -0.0005" to -0.0002" | 0.0015" to 0.0018" | Steel | Rockwell C50 | 00000000 | 00000 |
1" | 3/4" | 1 3/8" | 3/4" | 1.500" | 0.125" | 1.625" | -0.0005" to -0.0002" | 0.0018" to 0.0021" | Steel | Rockwell C50 | 00000000 | 00000 |
Head | Shoulder | Tolerance | |||||||||
---|---|---|---|---|---|---|---|---|---|---|---|
Dia. (A), mm | Ht. (B), mm | Shank Dia. (C), mm | Dia., mm | Ht., mm | O'all Ht., mm | Head Dia., mm | Shank Dia., mm | Material | Hardness | Each | |
Diamond Head | |||||||||||
6 | 6 | 10 | 13 | 2 | 17 | -0.00762 to 0 | -0.00762 to 0 | Steel | Rockwell C58-C62 | 0000000 | 000000 |
8 | 7 | 12 | 15 | 2 | 18 | -0.00762 to 0 | -0.00762 to 0 | Steel | Rockwell C58-C62 | 0000000 | 00000 |
10 | 9 | 15 | 18 | 2 | 22 | -0.00762 to 0 | -0.00762 to 0 | Steel | Rockwell C58-C62 | 0000000 | 00000 |
12 | 10 | 18 | 22 | 2 | 23 | -0.00762 to 0 | -0.00762 to 0 | Steel | Rockwell C58-C62 | 0000000 | 00000 |
Shank | Shoulder | Tolerance | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Pin Head Dia. | ID | Dia. (C) | Ht. (D) | Dia. | Ht. | O'all Ht. | Shank Dia. | Shank Ht. | ID | Material | Hardness | Each | |
For Tapered-Head Pins | |||||||||||||
1/4" | 1/4" | 1/2" | 3/8" | 0.625" | 0.094" | 0.469" | 0.0014" to 0.0017" | 0.0014" to 0.0017" | 0.0001" to 0.0005" | Steel | Rockwell C60-C64 | 000000000 | 00000 |
5/16" | 5/16" | 1/2" | 3/8" | 0.625" | 0.094" | 0.469" | 0.0014" to 0.0017" | 0.0014" to 0.0017" | 0.0001" to 0.0005" | Steel | Rockwell C60-C64 | 000000000 | 0000 |
3/8" | 3/8" | 5/8" | 1/2" | 0.750" | 0.094" | 0.594" | 0.0014" to 0.0017" | 0.0014" to 0.0017" | 0.0001" to 0.0005" | Steel | Rockwell C60-C64 | 000000000 | 0000 |
1/2" | 1/2" | 3/4" | 5/8" | 0.875" | 0.094" | 0.719" | 0.0015" to 0.0018" | 0.0015" to 0.0018" | 0.0001" to 0.0005" | Steel | Rockwell C60-C64 | 000000000 | 0000 |
For Diamond- and Round-Head Pins | |||||||||||||
1/4" | 1/4" | 13/32" | 7/16" | 0.563" | 0.063" | 0.500" | 0.0014" to 0.0017" | __ | 0.0001" to 0.0005" | Steel | Rockwell C60-C64 | 00000000 | 0000 |
5/16" | 5/16" | 1/2" | 7/16" | 0.625" | 0.063" | 0.500" | 0.0014" to 0.0017" | __ | 0.0001" to 0.0005" | Steel | Rockwell C60-C64 | 00000000 | 0000 |
3/8" | 3/8" | 5/8" | 7/16" | 0.750" | 0.063" | 0.500" | 0.0014" to 0.0017" | __ | 0.0001" to 0.0005" | Steel | Rockwell C60-C64 | 00000000 | 0000 |
1/2" | 1/2" | 3/4" | 1/2" | 0.875" | 0.063" | 0.562" | 0.0015" to 0.0018" | __ | 0.0001" to 0.0005" | Steel | Rockwell C60-C64 | 00000000 | 0000 |
5/8" | 5/8" | 7/8" | 1/2" | 1.000" | 0.125" | 0.625" | 0.0015" to 0.0018" | __ | 0.0002" to 0.0006" | Steel | Rockwell C60-C64 | 00000000 | 0000 |
3/4" | 3/4" | 1" | 1/2" | 1.125" | 0.125" | 0.625" | 0.0015" to 0.0018" | __ | 0.0002" to 0.0006" | Steel | Rockwell C60-C64 | 00000000 | 0000 |
1" | 1" | 1 3/8" | 11/16" | 1.500" | 0.125" | 0.812" | 0.0018" to 0.0021" | __ | 0.0002" to 0.0006" | Steel | Rockwell C60-C64 | 00000000 | 0000 |
For Cone-Head Pins | |||||||||||||
7/16" | 3/8" | 1/2" | 1/4" | 0.750" | 0.250" | 0.500" | 0.0014" to 0.0017" | -0.015" to 0.015" | -0.01" to 0" | Steel | Rockwell C60-C64 | 00000000 | 00000 |
11/16" | 5/8" | 3/4" | 3/8" | 1.000" | 0.375" | 0.750" | 0.0015" to 0.0018" | -0.015" to 0.015" | -0.014" to -0.004" | Steel | Rockwell C60-C64 | 00000000 | 00000 |
Shank | Shoulder | Tolerance | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Pin Head Dia., mm | ID, mm | Dia. (C), mm | Ht. (D), mm | Dia., mm | Ht., mm | O'all Ht., mm | Shank Dia., mm | Shank Ht., mm | ID, mm | Material | Hardness | Each | |
For Tapered-Head Pins | |||||||||||||
6 | 6 | 10 | 7 | 13 | 3 | 10 | -0.00762 to 0 | -0.254 to 0.254 | 0 to 0.0102 | Steel | Rockwell C58-C62 | 0000000 | 000000 |
8 | 8 | 12 | 7 | 15 | 3 | 10 | -0.00762 to 0 | -0.254 to 0.254 | 0 to 0.0102 | Steel | Rockwell C58-C62 | 0000000 | 00000 |
10 | 10 | 15 | 9 | 18 | 3 | 12 | -0.00762 to 0 | -0.254 to 0.254 | 0 to 0.0102 | Steel | Rockwell C58-C62 | 0000000 | 00000 |
12 | 12 | 18 | 12 | 22 | 3 | 15 | -0.00762 to 0 | -0.254 to 0.254 | 0 to 0.0102 | Steel | Rockwell C58-C62 | 0000000 | 00000 |
For Diamond- and Round-Head Pins | |||||||||||||
6 | 6 | 10 | 8 | 13 | 2 | 10 | -0.00762 to 0 | -0.254 to 0.254 | 0 to 0.0102 | Steel | Rockwell C58-C62 | 0000000 | 00000 |
8 | 8 | 12 | 8 | 15 | 2 | 10 | -0.00762 to 0 | -0.254 to 0.254 | 0 to 0.0102 | Steel | Rockwell C58-C62 | 0000000 | 00000 |
10 | 10 | 15 | 10 | 18 | 2 | 12 | -0.00762 to 0 | -0.254 to 0.254 | 0 to 0.0102 | Steel | Rockwell C58-C62 | 0000000 | 00000 |
12 | 12 | 18 | 10 | 22 | 2 | 12 | -0.00762 to 0 | -0.254 to 0.254 | 0 to 0.0102 | Steel | Rockwell C58-C62 | 0000000 | 00000 |
Shoulder-Style Locating Pins

The shoulder provides a consistent height reference point and keeps the pin from being pressed through the fixture. Install these pins in a plate or table and mate with holes in a workpiece for precise alignment. Press the shank into a drilled hole for permanent installation.
Diamond-head pins make less contact with the inside of a hole than round-head pins to reduce sticking and jamming.
For technical drawings and 3-D models, click on a part number.
Head | Shoulder | Tolerance | Diamond Head | |||||||
---|---|---|---|---|---|---|---|---|---|---|
Dia. (A) | Ht. (B) | Shank Dia. (C) | Dia. | Ht. | O'all Ht. | Head Dia. | Shank Dia. | Hardness | Each | |
Steel | ||||||||||
1/8" | 7/16" | 5/16" | 5/8" | 17/64" | 1 3/16" | 0" to 0.0005" | 0" to 0.0005" | Rockwell C60 | 00000000 | 000000 |
3/16" | 7/16" | 5/16" | 5/8" | 17/64" | 1 3/16" | 0" to 0.0005" | 0" to 0.0005" | Rockwell C60 | 00000000 | 00000 |
1/4" | 7/16" | 5/16" | 5/8" | 17/64" | 1 3/16" | 0" to 0.0005" | 0" to 0.0005" | Rockwell C60 | 00000000 | 00000 |
5/16" | 7/16" | 5/16" | 5/8" | 17/64" | 1 3/16" | 0" to 0.0005" | 0" to 0.0005" | Rockwell C60 | 00000000 | 00000 |
11/32" | 1/2" | 1/2" | 7/8" | 17/64" | 1 1/2" | 0" to 0.0005" | 0" to 0.0005" | Rockwell C60 | 00000000 | 00000 |
3/8" | 1/2" | 1/2" | 7/8" | 17/64" | 1 1/2" | 0" to 0.0005" | 0" to 0.0005" | Rockwell C60 | 00000000 | 00000 |
13/32" | 1/2" | 1/2" | 7/8" | 17/64" | 1 1/2" | 0" to 0.0005" | 0" to 0.0005" | Rockwell C60 | 00000000 | 00000 |
7/16" | 1/2" | 1/2" | 7/8" | 17/64" | 1 1/2" | 0" to 0.0005" | 0" to 0.0005" | Rockwell C60 | 00000000 | 00000 |
1/2" | 1/2" | 1/2" | 7/8" | 17/64" | 1 1/2" | 0" to 0.0005" | 0" to 0.0005" | Rockwell C60 | 00000000 | 00000 |
9/16" | 11/16" | 3/4" | 1 1/8" | 17/64" | 1 15/16" | 0" to 0.0005" | 0" to 0.0005" | Rockwell C60 | 00000000 | 00000 |
5/8" | 11/16" | 3/4" | 1 1/8" | 17/64" | 1 15/16" | 0" to 0.0005" | 0" to 0.0005" | Rockwell C60 | 00000000 | 00000 |
3/4" | 11/16" | 3/4" | 1 1/8" | 17/64" | 1 15/16" | 0" to 0.0005" | 0" to 0.0005" | Rockwell C60 | 00000000 | 00000 |
1" | 1" | 1" | 1 1/2" | 17/64" | 2 5/8" | 0" to 0.0005" | 0" to 0.0005" | Rockwell C60 | 00000000 | 00000 |
Threaded Locating Pins

Screw the shank into a threaded hole for quick installation and removal. Mate these pins with holes in workpieces for precise alignment.
Diamond-head pins make less contact with the inside of a hole than round-head pins to reduce sticking and jamming.
For technical drawings and 3-D models, click on a part number.
Head | Thread | Diamond Head | |||||||
---|---|---|---|---|---|---|---|---|---|
Dia. (A) | Ht. (B) | Size | Lg. | Shoulder Ht. | O'all Ht. | Head Dia. Tolerance | Hardness | Each | |
Steel | |||||||||
1/8" | 7/16" | 1/4"-28 | 5/16" | 3/32" | 1 1/4" | -0.001" to -0.0005" | Rockwell C60-C64 | 0000000 | 000000 |
3/16" | 7/16" | 1/4"-28 | 5/16" | 3/32" | 1 1/4" | -0.001" to -0.0005" | Rockwell C60-C64 | 0000000 | 00000 |
1/4" | 7/16" | 1/4"-20 | 5/16" | 3/32" | 1 1/4" | -0.0015" to -0.001" | Rockwell C60-C64 | 0000000 | 00000 |
1/4" | 7/16" | 1/4"-28 | 5/16" | 3/32" | 1 1/4" | -0.0015" to -0.001" | Rockwell C60-C64 | 0000000 | 00000 |
5/16" | 7/16" | 1/4"-20 | 5/16" | 3/32" | 1 1/4" | -0.001" to -0.0005" | Rockwell C60-C64 | 0000000 | 00000 |
5/16" | 7/16" | 1/4"-28 | 5/16" | 3/32" | 1 1/4" | -0.001" to -0.0005" | Rockwell C60-C64 | 0000000 | 00000 |
3/8" | 1/2" | 3/8"-24 | 1/2" | 1/8" | 1 19/32" | -0.0015" to -0.001" | Rockwell C60-C64 | 0000000 | 00000 |
7/16" | 1/2" | 3/8"-24 | 1/2" | 1/8" | 1 19/32" | -0.0015" to -0.001" | Rockwell C60-C64 | 0000000 | 00000 |
1/2" | 11/16" | 1/2"-13 | 11/16" | 5/32" | 2 1/8" | -0.0015" to -0.001" | Rockwell C60-C64 | 0000000 | 00000 |
1/2" | 11/16" | 1/2"-20 | 11/16" | 5/32" | 2 1/8" | -0.0015" to -0.001" | Rockwell C60-C64 | 0000000 | 00000 |
9/16" | 11/16" | 1/2"-20 | 21/32" | 5/32" | 2 1/8" | -0.0015" to -0.001" | Rockwell C60-C64 | 0000000 | 00000 |
3/4" | 1" | 3/4"-16 | 23/32" | 1/4" | 2 31/32" | -0.0015" to -0.001" | Rockwell C60-C64 | 0000000 | 00000 |
1" | 1" | 3/4"-16 | 23/32" | 1/4" | 2 31/32" | -0.0015" to -0.001" | Rockwell C60-C64 | 0000000 | 00000 |
Removable Locating Pins


A slightly undersized shank makes these pins easy to install and replace. Also known as slip-fit and lock-screw locating pins, they are held in place by a lock screw (sold separately). Mate pins with holes in workpieces for precise alignment. The shoulder provides a consistent height reference point.
Diamond-head pins make less contact with the inside of a hole than round-head pins to reduce sticking and jamming.
For technical drawings and 3-D models, click on a part number.
Head | Shoulder | Tolerance | Diamond Head | ||||||||
---|---|---|---|---|---|---|---|---|---|---|---|
Dia. (A) | Ht. (B) | Shank Dia. (C) | Dia. | Ht. | O'all Ht. | Lock Screw/Pin Ctr.-to-Ctr. | Head Dia. | Shank Dia. | Hardness | Each | |
Steel | |||||||||||
1/8" | 7/16" | 5/16" | 5/8" | 17/64" | 1 3/16" | 33/64" | -0.001" to -0.0005" | -0.0002" to 0" | Rockwell C60 | 0000000 | 000000 |
3/16" | 7/16" | 5/16" | 5/8" | 17/64" | 1 3/16" | 33/64" | -0.001" to -0.0005" | -0.0002" to 0" | Rockwell C60 | 0000000 | 00000 |
1/4" | 7/16" | 5/16" | 5/8" | 17/64" | 1 3/16" | 33/64" | -0.001" to -0.0005" | -0.0002" to 0" | Rockwell C60 | 0000000 | 00000 |
5/16" | 7/16" | 5/16" | 5/8" | 17/64" | 1 3/16" | 33/64" | -0.001" to -0.0005" | -0.0002" to 0" | Rockwell C60 | 0000000 | 00000 |
3/8" | 1/2" | 1/2" | 7/8" | 17/64" | 1 1/2" | 41/64" | -0.0015" to -0.001" | -0.0002" to 0" | Rockwell C60 | 0000000 | 00000 |
7/16" | 1/2" | 1/2" | 7/8" | 17/64" | 1 1/2" | 41/64" | -0.0015" to -0.001" | -0.0002" to 0" | Rockwell C60 | 0000000 | 00000 |
1/2" | 1/2" | 1/2" | 7/8" | 17/64" | 1 1/2" | 41/64" | -0.0015" to -0.001" | -0.0002" to 0" | Rockwell C60 | 0000000 | 00000 |
9/16" | 11/16" | 3/4" | 1 1/8" | 17/64" | 1 15/16" | 49/64" | -0.0015" to -0.001" | -0.0002" to 0" | Rockwell C60 | 0000000 | 00000 |
5/8" | 11/16" | 3/4" | 1 1/8" | 17/64" | 1 15/16" | 49/64" | -0.0014" to -0.0009" | -0.0002" to 0" | Rockwell C60 | 0000000 | 00000 |
3/4" | 11/16" | 3/4" | 1 1/8" | 17/64" | 1 15/16" | 49/64" | -0.0015" to -0.001" | -0.0002" to 0" | Rockwell C60 | 0000000 | 00000 |
1" | 1" | 1" | 1 1/2" | 17/64" | 2 5/8" | 61/64" | -0.0015" to -0.001" | -0.0002" to 0" | Rockwell C60 | 0000000 | 00000 |
Cast-In Locating Pins for Plastics

Encase these pins while molding plastic or composite parts. Once set, the knurls resist movement, letting you align the workpiece with precision on a plate or table.
Diamond-head pins make less contact with the inside of a hole than round-head pins, reducing sticking and jamming. Locate a workpiece using one of each head type for smooth loading and unloading.
Head | Tolerance | Diamond Head | ||||||
---|---|---|---|---|---|---|---|---|
Dia. (A) | Ht. (B) | Shank Dia. (C) | O'all Ht. | Head Dia. | Shank Dia. | Hardness | Each | |
Steel | ||||||||
3/32" | 7/16" | 3/8" | 13/16" | -0.0016" to -0.0014" | -0.005" to 0.005" | Rockwell C60 | 0000000 | 000000 |
1/8" | 7/16" | 3/8" | 13/16" | -0.0017" to -0.0015" | -0.005" to 0.005" | Rockwell C60 | 0000000 | 00000 |
5/32" | 7/16" | 3/8" | 13/16" | -0.0016" to -0.0014" | -0.005" to 0.005" | Rockwell C60 | 0000000 | 00000 |
3/16" | 7/16" | 3/8" | 13/16" | -0.0017" to -0.0015" | -0.005" to 0.005" | Rockwell C60 | 0000000 | 00000 |
1/4" | 7/16" | 3/8" | 13/16" | -0.0017" to -0.0015" | -0.005" to 0.005" | Rockwell C60 | 0000000 | 00000 |
5/16" | 1/2" | 9/16" | 7/8" | -0.0022" to -0.002" | -0.005" to 0.005" | Rockwell C60 | 0000000 | 00000 |
3/8" | 1/2" | 9/16" | 7/8" | -0.0022" to -0.002" | -0.005" to 0.005" | Rockwell C60 | 0000000 | 00000 |
7/16" | 11/16" | 11/16" | 1 3/16" | -0.0022" to -0.002" | -0.005" to 0.005" | Rockwell C60 | 0000000 | 00000 |
1/2" | 11/16" | 11/16" | 1 3/16" | -0.0022" to -0.002" | -0.005" to 0.005" | Rockwell C60 | 0000000 | 00000 |
9/16" | 13/16" | 3/4" | 1 9/16" | -0.0022" to -0.002" | -0.005" to 0.005" | Rockwell C60 | 0000000 | 00000 |
5/8" | 13/16" | 3/4" | 1 9/16" | -0.0022" to -0.002" | -0.005" to 0.005" | Rockwell C60 | 0000000 | 00000 |
Long-Life Grinding Bits for Nonmetals







The diamond abrasive in these bits is extremely hard and lasts longer than tungsten carbide. For longer tool life and improved finish, use a water- or oil-soluble mist or coolant.
Bits are also known as mounted points and die grinder bits. Head diameter is measured at the widest point.
Caution: As bit shank is exposed beyond 1/2", maximum safe rpm decreases significantly. Refer to ANSI standard B7.1. Use only accessories that have a greater rpm rating than the maximum speed of the grinder you choose.
For technical drawings and 3-D models, click on a part number.
Head | |||||||||
---|---|---|---|---|---|---|---|---|---|
Dia. | Lg. | Max. Speed, rpm | Shape | Abrasive Material | O'all Lg. | Grit (Surface Texture) | Each | ||
For Carbide, Ceramics, Glass | |||||||||
1/8" Shank Dia. | |||||||||
1 | 0.03" | 0.08" | 100,000 | Cylindrical | Diamond | 2 1/4" | 220 (Extra Smooth) Silver | 0000000 | 000000 |
1 | 0.03" | 0.19" | 96,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.04" | 0.08" | 100,000 | Cylindrical | Diamond | 2 1/4" | 220 (Extra Smooth) Silver | 0000000 | 00000 |
1 | 0.04" | 0.19" | 96,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.05" | 0.08" | 100,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.05" | 0.19" | 96,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.06" | 0.12" | 100,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.06" | 1/4" | 96,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.07" | 0.12" | 100,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.08" | 0.16" | 100,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.08" | 1/4" | 96,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.09" | 0.16" | 100,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.1" | 0.16" | 100,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.11" | 0.16" | 60,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.12" | 0.16" | 60,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.13" | 0.2" | 60,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.13" | 1/4" | 96,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.14" | 0.2" | 60,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.16" | 0.2" | 60,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.16" | 1/4" | 96,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.19" | 0.31" | 96,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.25" | 0.31" | 46,500 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.31" | 0.31" | 46,500 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
2 | 0.25" | 0.03" | 46,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
2 | 0.25" | 0.06" | 46,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
2 | 0.25" | 0.13" | 46,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
3 | 0.06" | 1/4" | 96,000 | Barrel | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
3 | 0.13" | 1/4" | 96,000 | Barrel | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
3 | 0.25" | 0.31" | 46,000 | Barrel | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
3 | 0.31" | 0.31" | 46,000 | Barrel | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
4 | 0.14" | 0.31" | 96,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
5 | 0.06" | 0.31" | 96,000 | Barrel | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
5 | 0.08" | 0.31" | 96,000 | Barrel | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
5 | 0.11" | 0.31" | 96,000 | Barrel | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
6 | 0.16" | 0.23" | 96,000 | Taper | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
6 | 0.17" | 0.14" | 96,000 | Taper | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
6 | 0.19" | 0.38" | 96,000 | Taper | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1/4" Shank Dia. | |||||||||
1 | 0.06" | 1/4" | 96,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.09" | 1/4" | 96,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.13" | 1/4" | 96,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.19" | 0.31" | 96,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.2" | 0.24" | 60,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.24" | 0.28" | 60,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.25" | 0.31" | 46,500 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.26" | 0.28" | 60,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.31" | 0.31" | 46,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.32" | 0.32" | 30,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.34" | 0.32" | 30,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.38" | 0.31" | 46,500 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.39" | 0.39" | 30,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.5" | 0.31" | 30,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.59" | 0.39" | 20,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
1 | 0.73" | 0.39" | 20,000 | Cylindrical | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
3 | 0.38" | 0.31" | 46,000 | Barrel | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
3 | 0.5" | 0.31" | 30,000 | Barrel | Diamond | 2 1/4" | 120 (Smooth) Silver | 0000000 | 00000 |
7 | 0.19" | 0.1" | 18,600 | Flat-Top Cone | Diamond | 2" | 120 (Smooth) Silver | 0000000 | 00000 |
7 | 0.25" | 0.1" | 18,600 | Flat-Top Cone | Diamond | 2" | 120 (Smooth) Silver | 0000000 | 00000 |
7 | 0.5" | 0.2" | 30,000 | Flat-Top Cone | Diamond | 2" | 120 (Smooth) Silver | 0000000 | 00000 |
Burs for Masonry, Ceramics, and Composites
Diamond-cut teeth effectively cut hard materials.
Flat Cylinder—For straight edges and flat surfaces.
Flat Cutter Cylinder—For straight edges, flat surfaces, and flat-bottom holes and slots.
Rounded Cylinder—For curved surfaces and slots and round-bottom holes and slots.
Rounded Tree—For curved surfaces and slots and curved holes with rounded bottoms.
Pointed Tree—For curved surfaces and slots and curved holes with pointed bottoms.
Ball—For curved surfaces, round slots, and round-bottom holes.
Flame—For contoured surfaces, slots, and holes.
Oval/Egg—For oblong slots and holes.
Cone—For beveled edges and countersunk holes.
Inverted Cone—For inverted-angle holes and dovetailed slots.
Rounded Tapered Cone—For tapered holes and slots with rounded bottoms.
Pointed Tapered Cone—For tapered holes and slots with pointed bottoms.
For technical drawings and 3-D models, click on a part number.


Head | Diamond Cut (For Extra Fine Finish) | ||||||
---|---|---|---|---|---|---|---|
Shank Dia. | Dia. | Lg. | Overall Lg. | Bur Trade Number | For Use On | Each | |
Carbide | |||||||
1/4" | 1/4" | 5/8" | 2" | SA-1 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 0000000 | 000000 |
1/4" | 3/8" | 3/4" | 2 1/2" | SA-3 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 0000000 | 00000 |
1/4" | 1/2" | 1" | 2 3/4" | SA-5 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 0000000 | 00000 |


Head | Diamond Cut (For Extra Fine Finish) | ||||||
---|---|---|---|---|---|---|---|
Shank Dia. | Dia. | Lg. | Overall Lg. | Bur Trade Number | For Use On | Each | |
Carbide | |||||||
1/4" | 1/4" | 5/8" | 2" | SB-1 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 00000000 | 000000 |
1/4" | 3/8" | 3/4" | 2 1/2" | SB-3 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 00000000 | 00000 |
1/4" | 1/2" | 1" | 2 3/4" | SB-5 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 00000000 | 00000 |


Head | Diamond Cut (For Extra Fine Finish) | ||||||
---|---|---|---|---|---|---|---|
Shank Dia. | Dia. | Lg. | Overall Lg. | Bur Trade Number | For Use On | Each | |
Carbide | |||||||
1/4" | 1/4" | 5/8" | 2" | SC-1 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 0000000 | 000000 |
1/4" | 3/8" | 3/4" | 2 1/2" | SC-3 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 0000000 | 00000 |
1/4" | 1/2" | 1" | 2 3/4" | SC-5 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 0000000 | 00000 |


Head | Diamond Cut (For Extra Fine Finish) | ||||||
---|---|---|---|---|---|---|---|
Shank Dia. | Dia. | Lg. | Overall Lg. | Bur Trade Number | For Use On | Each | |
Carbide | |||||||
1/4" | 1/4" | 5/8" | 2" | SF-1 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 0000000 | 000000 |
1/4" | 3/8" | 3/4" | 2 1/2" | SF-3 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 0000000 | 00000 |
1/4" | 1/2" | 1" | 2 3/4" | SF-5 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 0000000 | 00000 |


Head | Diamond Cut (For Extra Fine Finish) | ||||||
---|---|---|---|---|---|---|---|
Shank Dia. | Dia. | Lg. | Overall Lg. | Bur Trade Number | For Use On | Each | |
Carbide | |||||||
1/4" | 1/4" | 5/8" | 2" | SG-1 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 0000000 | 000000 |
1/4" | 3/8" | 3/4" | 2 1/2" | SG-3 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 0000000 | 00000 |
1/4" | 1/2" | 1" | 2 3/4" | SG-5 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 0000000 | 00000 |


Head | Diamond Cut (For Extra Fine Finish) | ||||||
---|---|---|---|---|---|---|---|
Shank Dia. | Dia. | Lg. | Overall Lg. | Bur Trade Number | For Use On | Each | |
Carbide | |||||||
1/4" | 1/4" | 7/32" | 2" | SD-1 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 0000000 | 000000 |
1/4" | 3/8" | 5/16" | 2 1/8" | SD-3 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 0000000 | 00000 |
1/4" | 1/2" | 7/16" | 2 1/4" | SD-5 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 0000000 | 00000 |


Head | Diamond Cut (For Extra Fine Finish) | ||||||
---|---|---|---|---|---|---|---|
Shank Dia. | Dia. | Lg. | Overall Lg. | Bur Trade Number | For Use On | Each | |
Carbide | |||||||
1/4" | 1/4" | 1/2" | 2" | SH-1 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 0000000 | 000000 |
1/4" | 5/16" | 3/4" | 2 1/2" | SH-2 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 0000000 | 00000 |
1/4" | 1/2" | 1 1/4" | 3" | SH-5 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 0000000 | 00000 |


Head | Diamond Cut (For Extra Fine Finish) | ||||||
---|---|---|---|---|---|---|---|
Shank Dia. | Dia. | Lg. | Overall Lg. | Bur Trade Number | For Use On | Each | |
Carbide | |||||||
1/4" | 1/4" | 3/8" | 2" | SE-1 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 00000000 | 000000 |
1/4" | 3/8" | 5/8" | 2 3/8" | SE-3 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 00000000 | 00000 |
1/4" | 1/2" | 7/8" | 2 5/8" | SE-5 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 00000000 | 00000 |


Head | Diamond Cut (For Extra Fine Finish) | |||||||
---|---|---|---|---|---|---|---|---|
Shank Dia. | Dia. | Lg. | Tip Angle | Overall Lg. | Bur Trade Number | For Use On | Each | |
Carbide | ||||||||
1/4" | 1/4" | 1/8" | 90° | 2" | SK-1 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 00000000 | 000000 |
1/4" | 1/4" | 3/16" | 60° | 2" | SJ-1 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 00000000 | 00000 |
1/4" | 3/8" | 3/16" | 90° | 1 15/16" | SK-3 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 00000000 | 00000 |
1/4" | 3/8" | 5/16" | 60° | 2 1/16" | SJ-3 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 00000000 | 00000 |
1/4" | 1/2" | 1/4" | 90° | 2" | SK-5 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 00000000 | 00000 |
1/4" | 1/2" | 7/16" | 60° | 2 3/16" | SJ-5 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 00000000 | 00000 |


Head | Diamond Cut (For Extra Fine Finish) | |||||||
---|---|---|---|---|---|---|---|---|
Shank Dia. | Dia. | Lg. | Tip Angle | Overall Lg. | Bur Trade Number | For Use On | Each | |
Carbide | ||||||||
1/4" | 1/4" | 5/16" | 10° | 2" | SN-1 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 00000000 | 000000 |
1/4" | 3/8" | 3/8" | 15° | 2 1/8" | SN-2 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 00000000 | 00000 |
1/4" | 1/2" | 1/2" | 12° | 2 1/4" | SN-3 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 00000000 | 00000 |


Head | Diamond Cut (For Extra Fine Finish) | |||||||
---|---|---|---|---|---|---|---|---|
Shank Dia. | Dia. | Lg. | Tip Angle | Overall Lg. | Bur Trade Number | For Use On | Each | |
Carbide | ||||||||
1/4" | 1/4" | 5/8" | 14° | 2" | SL-1 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 00000000 | 000000 |
1/4" | 3/8" | 1 1/16" | 14° | 2 13/16" | SL-3 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 00000000 | 00000 |
1/4" | 1/2" | 1 1/8" | 14° | 2 7/8" | SL-4 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 00000000 | 00000 |


Head | Diamond Cut (For Extra Fine Finish) | |||||||
---|---|---|---|---|---|---|---|---|
Shank Dia. | Dia. | Lg. | Tip Angle | Overall Lg. | Bur Trade Number | For Use On | Each | |
Carbide | ||||||||
1/4" | 1/4" | 1/2" | 22° | 2" | SM-1 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 00000000 | 000000 |
1/4" | 3/8" | 5/8" | 28° | 2 1/2" | SM-4 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 00000000 | 00000 |
1/4" | 1/2" | 7/8" | 28° | 2 5/8" | SM-5 | Ceramics, Brick, Stone, Concrete, Glass, Fiberglass, Carbon Fiber, Graphite | 00000000 | 00000 |