M7 Dies | McMaster-Carr

Cut and repair threads and drill holes in many different sizes. Tap and die wrenches are included. The dies are hex shaped for use with conventional wrenches. The taps are made of carbon steel and are recommended for thread repair and occasional tapping.

Taper Chamfer—Taper chamfer taps have 7-10 chamfered threads at the tip for cutting into the workpiece. They require less torque than other chamfer types, making them a good choice for starting threads and tapping through holes. However, a longer taper means that they cannot thread as close to the bottom of closed-end holes.

Plug Chamfer—Plug chamfer taps are a versatile choice for most tapping applications. With 3-5 chamfered cutting threads, they require moderate torque and are often used for start-to-finish tapping of through holes and closed-end holes. However, they do not start threads as easily as taper chamfers. When using them to tap closed-end holes, be sure to leave sufficient space at the bottom for chips to accumulate.

	Drill Bit Sizes Included	Container Type	Includes	Tap Chamfer Type		Each
Carbon Steel







	Right-Hand Thread

	117	4-40, 6-32, 8-32, 10-24, 10-32, 12-24, 1/8"-27, 1/8"-28, 1/4"-20, 1/4"-28, 5/16"-18, 5/16"-24, 3/8"-16, 3/8"-24, 7/16"-14, 7/16"-20, 1/2"-13, 1/2"-20, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm	4-40, 6-32, 8-32, 10-24, 10-32, 12-24, 1/8"-27, 1/8"-28, 1/4"-20, 1/4"-28, 5/16"-18, 5/16"-24, 3/8"-16, 3/8"-24, 7/16"-14, 7/16"-20, 1/2"-13, 1/2"-20, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm	5/64", 7/64", 5/32", 1/4", 19/64", 5/16", 21/64", 3/8", 25/64", 13/32", 27/64", 29/64", 43 ga., 39 ga., 36 ga., 30 ga., 29 ga., 25 ga., 21 ga., 20 ga., 16 ga., 9 ga., 7 ga., 3 ga., B, F, H, I, J, O, Q, R, S, U, Z	Plastic Case	Die Wrench (2), Extractor (5), Tap Wrench (3), Thread Gauge (2)	Taper, Plug	00000000	0000000

Tap and Die Sets

Use a single set for many sizes of internal and external threads. The taps and dies are for use on most metal and plastic.

Carbon Steel—Carbon steel taps are for thread repair and occasional tapping.

Plug Chamfer—Plug-chamfer taps are a versatile choice for most tapping applications. With 3-5 chamfered cutting threads, they require moderate torque and are often used for start-to-finish tapping of through holes and closed-end holes. However, they do not start threads as easily as taper-chamfer taps. When using them to tap closed-end holes, be sure to leave sufficient space at the bottom for chips to accumulate.

Taper Chamfer—Taper-chamfer taps have 7-10 chamfered threads at the tip for cutting into the workpiece. They require less torque than other chamfer types, making them a good choice for starting threads and tapping through holes. However, a longer taper means that they cannot thread as close to the bottom of closed-end holes.

Hex—Hex-shaped dies are for thread repair and can be used with conventional wrenches.

	Die Shape	Die Sizes Included	Wd.	Container Type	Includes		Each
Carbon Steel Taps and Dies







	Right-Hand Thread

	24	1/8"-28, M3 × 0.50 mm, M4 × 0.70 mm, M5 × 0.80 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.25 mm, M9 × 1.25 mm, M10 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm	Plug, Taper	Hex	1/8"-28, M3 × 0.50 mm, M4 × 0.70 mm, M5 × 0.80 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.25 mm, M9 × 1.25 mm, M10 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm	1"	Plastic Case	Die Wrench, Tap Wrench	00000000	0000000


	40	6-32, 8-32, 10-24, 1/8"-27, 1/4"-20, 5/16"-18, 3/8"-16, 7/16"-14, 1/2"-13, M4 × 0.75 mm, M5 × 0.80 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M12 × 1.75 mm	Plug, Taper	Hex	6-32, 8-32, 10-24, 1/8"-27, 1/4"-20, 5/16"-18, 3/8"-16, 7/16"-14, 1/2"-13, M4 × 0.75 mm, M5 × 0.80 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M12 × 1.75 mm	5/8", 1"	Plastic Case	Die Wrench (2), Tap Wrench (3), Thread Gauge	0000000	000000
	40	1/8"-28, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm	Plug, Taper	Hex	1/8"-28, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm	5/8", 1"	Plastic Case	Die Wrench (2), Tap Wrench (3), Thread Gauge	0000000	000000
	52	1/4"-19, 1/8"-28, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm, M14 × 1.25 mm, M14 × 2.00 mm, M16 × 1.50 mm, M16 × 2.00 mm, M18 × 1.50 mm, M18 × 2.50 mm	Plug, Taper	Hex	1/8"-28, 1/4"-19, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm, M14 × 1.25 mm, M14 × 2.00 mm, M16 × 1.50 mm, M16 × 2.00 mm, M18 × 1.50 mm, M18 × 2.50 mm	1", 1 7/16"	Plastic Case	Die Wrench (2), Tap Wrench (3), Thread Gauge	0000000	000000
	65	1/8"-28, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm, M14 × 1.25 mm, M14 × 1.50 mm, M14 × 2.00 mm, M16 × 1.50 mm, M16 × 2.00 mm, M18 × 1.50 mm, M18 × 2.50 mm, M20 × 2.50 mm, M22 × 1.50 mm, M24 × 2.00 mm, M24 × 3.00 mm	Plug, Taper	Hex	1/8"-28, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm, M14 × 1.25 mm, M14 × 1.50 mm, M14 × 2.00 mm, M16 × 1.50 mm, M16 × 2.00 mm, M18 × 1.50 mm, M18 × 2.50 mm, M20 × 2.50 mm, M22 × 1.50 mm, M24 × 2.00 mm, M24 × 3.00 mm	5/8", 1", 1 3/16", 1 7/16", 1 13/16"	Plastic Case	Die Wrench (4), Tap Wrench (4), Thread Gauge	0000000	000000

Thread-Repairing Die Nut Sets

The dies in these sets match the width of hex nuts that are the same thread size, so one tool can turn both. For tight spaces, use with a ratcheting wrench since it requires minimal clearance to turn. Repairing dies remove imperfections and rust so threads engage properly for a strong connection.

	Thread Size	Thread Type	Wd., mm	Container Type		Each
Uncoated Carbon Steel



	5	M6, M7, M8, M10, M12	Metric	11, 14, 18, 19	Plastic Pouch	0000000	00000

Tap, Die, and Thread File Sets

Repair screw threads in a wide range of sizes. The dies are hex shaped for use with conventional wrenches. The taps have a square shank that's compatible with tap wrenches and tap holders for drill presses and drilling machines. With a plug chamfer, all taps have 3-5 chamfered threads and are suitable for thread repair in both through holes and closed-end holes.

	File Sizes Included	Container Type		Each
Carbon Steel







	Right-Hand Thread

	48	1/2"-13, 1/2"-20, 1/4”-20, 1/4”-28, 3/8"-16, 3/8"-24, 5/16"-24, 5/16”-18, 7/16"-14, 7/16"-20, 9/16"-18, 9/16”-12, M6 × 1.00 mm, M8 × 1.25 mm, M10 × 1.00 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.25 mm, M12 × 1.50 mm, M12 × 1.75 mm, M14 × 1.50 mm	1/2"-13, 1/2"-20, 1/4"-20, 1/4"-28, 3/8"-16, 3/8"-24, 5/16"-18, 5/16"-24, 5/8"-11, 5/8"-18, 7/16"-14, 7/16"-20, 9/16"-12, 9/16"-18, M6 × 1.00 mm, M8 × 1.25 mm, M10 × 1.00 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.25 mm, M12 × 1.50 mm, M12 × 1.75 mm, M14 × 1.50 mm	For 0.75 to 3 mm thread pitches, For 11 to 24 threads per inch	Plastic Case	00000000	0000000

Dies

Rotate these dies around studs and rods to create new fastener threads. A cut above lower-quality dies that can leave inferior threads, these are machined in the U.S. to precise dimensions for accuracy and consistency.

They are adjustable, so you can cut a shallow thread that makes it easier to get the die started on the first pass. Turn the set screw to open the die to its largest diameter. Then rotate the die with a round die wrench and adjust the screw as you make additional passes to reach the proper thread size.

Uncoated High-Speed Steel—The most versatile dies stay sharp and cut cleanly, even if you use them every day. They last much longer than carbon steel dies and you won’t have to work as hard to create threads.

Titanium Nitride (TiN)-Coated High-Speed Steel—When you regularly work on challenging metals like stainless steel, choose dies with a TiN coating that reduces friction and resists heat. They turn faster and last longer than uncoated dies.

	Dies						Die Wrenches
			Uncoated High-Speed Steel		Titanium Nitride (TiN)-Coated High-Speed Steel
	Thread Size	Thread Type		Each		Each		Each
1" OD



		M7 × 0.75 mm	Metric	0000000	000000	———	0	00000000	00000


		M7 × 1 mm	Metric	0000000	00000	0000000	0000000	00000000	0000

Thread-Repairing Dies

Rescue mangled threads and return them to like-new condition. By repairing threads, you don’t have to replace the fastener or resize holes. These dies smooth out flaws and remove rust so threads engage properly and connections stay strong. Turn them with a hex die wrench or a standard adjustable wrench.

Don’t risk damaging threads further with an inferior-quality die. Our dies are machined in the U.S. to precise dimensions for a perfect thread profile.

Uncoated Carbon Steel—Hard and wear resistant for a long life, these dies work well on both metal and plastic.

			Uncoated Carbon Steel
Thread Size	Thread Type	Wd.		Each
M7 × 1 mm	Metric	11/16"	0000000	000000

Thread-Repairing Die Nuts

If your wrench can turn a hex nut, it can turn these dies. They match the width of nuts of the same thread size, so you only need one tool to remove the nut, repair threads on the fastener, and put the nut back on. When space is tight, use dies with a ratcheting wrench since it requires minimal clearance to turn. Repairing dies remove imperfections and rust, resulting in threads that engage properly for a strong connection.

			Uncoated Carbon Steel
Thread Size	Thread Type	Wd., mm		Each
M7 × 1 mm	Metric	14	00000000	00000

Two-Piece Thread-Repairing Dies

Clamp the two halves of these dies around your bolt, stud, or rod to repair threads anywhere along the length. Since you don't have to spin them into place, they're often used on extra-long fasteners or when you can't access the end of your workpiece. Dies smooth damage, sharpen worn edges, and clean out rust so connections stay secure. Once in position, turn them with a hex die wrench or a standard adjustable wrench.

Black-Oxide Tool Steel—Hard and wear resistant for long life, these dies work well on both metal and plastic.

			Black-Oxide Tool Steel
Thread Size	Thread Type	Wd.		Each
M7 × 1 mm	Metric	1"	0000000	000000