McMaster-Carr logo
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Comments
    E-mail address (if you would like a response)
    135 Products

    Threaded on Both Ends Setup Studs

    Known as setup studs, these studs withstand sideways forces better than fully threaded studs because they have a strong unthreaded middle. The unthreaded middle also makes more contact with unthreaded holes, creating better alignment than a fully threaded stud.
    Steel
    Image of Product. Front orientation. Contains Annotated. Setup Studs.
    DIN 939—Studs that meet DIN standards meet dimensional and material requirements. Thread Length (B) includes chamfer on DIN 938 and DIN 939 studs.
    Thread,
    mm
    Lg.
    (A)
    Lg.
    (B)
    Lg.,
    mm
    Tensile Strength,
    psi
    Specs.
    Met
    Each
    M6 × 1 mm
    11623.5116,000DIN 93998867A25000000
    15627.5116,000DIN 93998867A2550000
    18637.5116,000DIN 93998867A2600000
    18647.5116,000DIN 93998867A2650000
    18657.5116,000DIN 93998867A2700000
     
    M8 × 1.25 mm
    14830116,000DIN 93998867A3100000
    19835116,000DIN 93998867A3150000
    22850116,000DIN 93998867A3200000
    22860116,000DIN 93998867A3250000
    22870116,000DIN 93998867A3300000
     
    M10 × 1.5 mm
    181037116,000DIN 93998867A3500000
    261062116,000DIN 93998867A3550000
    261072116,000DIN 93998867A3600000
    261092116,000DIN 93998867A3650000
     
    M12 × 1.75 mm
    231345116,000DIN 93998867A4100000
    301365116,000DIN 93998867A4150000
    301375116,000DIN 93998867A4200000
    301395116,000DIN 93998867A4250000
    3013115116,000DIN 93998867A4300000
     
    M16 × 2 mm
    271855116,000DIN 93998867A5100000
    381870116,000DIN 93998867A5150000
    381885116,000DIN 93998867A5200000
    3818100116,000DIN 93998867A5250000
    3818120116,000DIN 93998867A5300000
     
    Black Oxide Steel
    Image of Product. Front orientation. Contains Annotated. Setup Studs.
    Black-oxide steel studs resist rusting in dry environments.
    DIN 939—Studs that meet DIN standards meet dimensional and material requirements. Thread Length (B) includes chamfer on DIN 938 and DIN 939 studs.
    Thread,
    mm
    Lg.
    (A)
    Lg.
    (B)
    Lg.,
    mm
    Tensile Strength,
    psi
    Specs.
    Met
    Each
    M6 × 1 mm
    202050125,000DIN 93993275A01400000
    272780125,000DIN 93993275A0190000
    3131110125,000DIN 93993275A0220000
    3535175125,000DIN 93993275A0280000
     
    M8 × 1.25 mm
    202050125,000DIN 93993275A0300000
    202065125,000DIN 93993275A0310000
    272780125,000DIN 93993275A0320000
    313195125,000DIN 93993275A0330000
    3131110125,000DIN 93993275A0340000
    3535140125,000DIN 93993275A0350000
    3535150125,000DIN 93993275A0360000
    3535175125,000DIN 93993275A0370000
    3535200125,000DIN 93993275A0380000
     
    M10 × 1.5 mm
    202050125,000DIN 93993275A0390000
    202065125,000DIN 93993275A0400000
    272780125,000DIN 93993275A0410000
    313195125,000DIN 93993275A0420000
    3535110125,000DIN 93993275A0430000
    3535125125,000DIN 93993275A0440000
    3535140125,000DIN 93993275A0450000
    3535150125,000DIN 93993275A0460000
    3535175125,000DIN 93993275A0470000
    3535200125,000DIN 93993275A0480000
     
    M12 × 1.75 mm
    202050125,000DIN 93993275A0490000
    202065125,000DIN 93993275A0500000
    272780125,000DIN 93993275A0510000
    313195125,000DIN 93993275A0520000
    3939110125,000DIN 93993275A0530000
    3939125125,000DIN 93993275A0540000
    3939140125,000DIN 93993275A0550000
    3939150125,000DIN 93993275A0560000
    3939175125,000DIN 93993275A0570000
    3939200125,000DIN 93993275A0580000
     
    M16 × 2 mm
    212180125,000DIN 93993275A0590000
    313195125,000DIN 93993275A0600000
    4747110125,000DIN 93993275A0610000
    4747125125,000DIN 93993275A0660000
    4747150125,000DIN 93993275A0620000
    4747175125,000DIN 93993275A0630000
    4747200125,000DIN 93993275A0640000
    4747250125,000DIN 93993275A06500000
    4747300125,000DIN 93993275A1010000
     
    M20 × 2.5 mm
    272780125,000DIN 93993275A0670000
    313195125,000DIN 93993275A1050000
    4747110125,000DIN 93993275A0680000
    5555125125,000DIN 93993275A1080000
    5555150125,000DIN 93993275A06900000
    5555175125,000DIN 93993275A07000000
    5555200125,000DIN 93993275A07100000
     
    M24 × 3 mm
    3939100125,000DIN 93993275A07500000
    5555125125,000DIN 93993275A07600000
    6363150125,000DIN 93993275A07700000
     
    18-8 Stainless Steel
    Image of Product. Front orientation. Contains Annotated. Setup Studs.
    18-8 stainless steel studs have good chemical resistance and resist rusting in humid, damp, and washdown areas. They may be mildly magnetic.
    DIN 939—Studs that meet DIN standards meet dimensional and material requirements. Thread Length (B) includes chamfer on DIN 938 and DIN 939 studs.
    Thread,
    mm
    Lg.
    (A)
    Lg.
    (B)
    Lg.,
    mm
    Tensile Strength,
    psi
    Specs.
    Met
    Each
    M6 × 1 mm
    10823.570,000DIN 93992997A81100000
    1482770,000DIN 93992997A8120000
    1883270,000DIN 93992997A8130000
    1883770,000DIN 93992997A8140000
    1884270,000DIN 93992997A8150000
    1884770,000DIN 93992997A8160000
    1885770,000DIN 93992997A8170000
    1886770,000DIN 93992997A8180000
     
    M8 × 1.25 mm
    14103070,000DIN 93992997A8190000
    19103570,000DIN 93992997A8210000
    22104070,000DIN 93992997A8220000
    22104570,000DIN 93992997A8230000
    22105570,000DIN 93992997A8240000
    22106070,000DIN 93992997A8250000
    22106570,000DIN 93992997A8260000
    22107070,000DIN 93992997A8270000
     
    M10 × 1.5 mm
    13123270,000DIN 93992997A8280000
    18123770,000DIN 93992997A8290000
    23124270,000DIN 93992997A8310000
    26124770,000DIN 93992997A8320000
    26125770,000DIN 93992997A8330000
    26126270,000DIN 93992997A8340000
     
    316 Stainless Steel
    Image of Product. Front orientation. Contains Annotated. Setup Studs.
    316 stainless steel studs resist corrosion from chemicals and salt water better than 18-8 stainless steel studs. They may be mildly magnetic.
    DIN 939—Studs that meet DIN standards meet dimensional and material requirements. Thread Length (B) includes chamfer on DIN 938 and DIN 939 studs.
    Thread,
    mm
    Lg.
    (A)
    Lg.
    (B)
    Lg.,
    mm
    Tensile Strength,
    psi
    Specs.
    Met
    Each
    M6 × 1 mm
    11823.570,000DIN 9395580N11100000
    1582770,000DIN 9395580N1120000
    1883270,000DIN 9395580N1130000
    1883770,000DIN 9395580N1140000
    1884270,000DIN 9395580N1150000
    1884770,000DIN 9395580N1160000
    1885270,000DIN 9395580N1170000
    1885770,000DIN 9395580N1180000
    1886770,000DIN 9395580N1190000
     
    M8 × 1.25 mm
    14103070,000DIN 9395580N1210000
    19103570,000DIN 9395580N1220000
    22104070,000DIN 9395580N1230000
    22104570,000DIN 9395580N1240000
    22105070,000DIN 9395580N1250000
    22105570,000DIN 9395580N1260000
    22106070,000DIN 9395580N1270000
    22106570,000DIN 9395580N1280000
    22107070,000DIN 9395580N1290000
     
    M10 × 1.5 mm
    13123270,000DIN 9395580N1310000
    18123770,000DIN 9395580N1320000
    23124270,000DIN 9395580N1330000
    26124770,000DIN 9395580N1340000
    26125270,000DIN 9395580N1350000
    26125770,000DIN 9395580N1360000
    26126270,000DIN 9395580N1370000
     

    Vibration-Resistant Threaded on Both Ends Setup Studs

    Also known as tap-end studs, inch setup studs have Class 5 friction-fit threads on one end to resist loosening and Class 2A standard threads on the other end for attaching a nut. Metric setup studs have Class SK6 friction-fit threads on one end to resist loosening and Class 6g standard threads on the other end for attaching a nut. They are ideal for machining applications where vibration can loosen clamps. They withstand sideways forces better than fully threaded studs because they have an unthreaded middle that is stronger than the threaded ends. The unthreaded middle also makes more contact with unthreaded holes, creating better alignment than a fully threaded stud. Remove studs with pliers to reuse them.
    Steel
    Image of Product. Front orientation. Contains Annotated. Setup Studs. Vibration Resistant.
    DIN 939—Studs that meet DIN standards meet dimensional and material requirements. Thread Length (B) includes chamfer on DIN 938 and DIN 939 studs.
    Thread
    Lg. (A),
    mm
    Lg. (B),
    mm
    Fit (A)
    Fit (B)
    Lg.,
    mm
    Tensile Strength,
    psi
    Specs.
    Met
    Each
    M8 × 1.25 mm
    818Metric Interference Sk6Metric Class 6g
    35120,000DIN 93991059A51000000
    822Metric Interference Sk6Metric Class 6g
    45120,000DIN 93991059A5150000
    822Metric Interference Sk6Metric Class 6g
    60120,000DIN 93991059A5200000
    822Metric Interference Sk6Metric Class 6g
    70120,000DIN 93991059A5250000
     
    M10 × 1.5 mm
    1018Metric Interference Sk6Metric Class 6g
    37120,000DIN 93991059A5510000
    1023Metric Interference Sk6Metric Class 6g
    42120,000DIN 93991059A5560000
    1026Metric Interference Sk6Metric Class 6g
    52120,000DIN 93991059A5610000
    1026Metric Interference Sk6Metric Class 6g
    62120,000DIN 93991059A5660000
     
    M12 × 1.75 mm
    1217Metric Interference Sk6Metric Class 6g
    40120,000DIN 93991059A6050000
    1227Metric Interference Sk6Metric Class 6g
    50120,000DIN 93991059A6100000
    1230Metric Interference Sk6Metric Class 6g
    60120,000DIN 93991059A6150000
    1230Metric Interference Sk6Metric Class 6g
    70120,000DIN 93991059A6200000
     
    back to top