When used with a lid, these tote boxes protect contents from electrostatic discharge.

A lip on the back allows bin boxes to hang from rails or louvered panels.

A removable window allows 30% more capacity yet still lets you see what's in the box.

Grab the handle to pull the bin box forward. It has a tab on the back to catch the underside of a shelf when tilted. A raised front and back prevents spills.

These bins ship flat so you can keep plenty of extras on hand. They easily assemble without tape, glue, or fasteners.

Unlike other bin boxes, wire bin boxes are easy to clean and don't collect dust.

A wing joint opens wide for marking and transferring large circles, arcs, and measurements.

Draw or scribe circles and transfer measurements.

Turn your ruler into a compass by adding these point-holding clamps.

Combine these point-holding clamps with a pipe to create a compass that marks circles 1 1/2" diameter and larger.

Transfer measurements and draw large, precise circles.

These precision tools have a strong, flexible bow spring that holds the legs in place while a knurled nut allows you to make finer adjustments than other calipers.

With nothing to install, you can quickly set up temporary offices and meeting rooms.

With an easy-to-see frame and clear panels, these partitions let you safely establish sections or distance between people in your workspace.

The vinyl coating on these curtains withstands oil.

The vinyl coating on these panels withstands oil.

Lightweight and flexible enough to roll up and carry, these panels are wire reinforced so they stand on their own.

Shield workers while allowing them to see and be seen.

Combine straight and curved sections to build a hanging one- to four-sided curtain partition.

The aluminum on one side of these curtains reflects radiant heat.

Made with Kevlar to resist abrasion, scratches, tears, and punctures.

Mount with screws or tape.

The open wire design prevents dirt and dust buildup.

These binders mount to machines, equipment, and walls.

These binders have three rings for hole punched documents.

Mount these binders to machines, equipment, walls, and flat surfaces to create permanent viewing spots and free up desk space—they display documents in a way that’s sanitary for all users.

These kits include all brackets and fasteners needed for mounting partitions.

Design your own partitions, add to your existing partition, or replace individual components and hardware.

Typically used for separating work areas such as wash bays, these curtains have a clear center section that allows you to see in as well as out.

Use these telescoping poles with tarps, drop cloths, and plastic sheeting up to 8 mils thick to create a sturdy, temporary wall and control dust and debris.

These cabinets have open shelves for storing larger supplies and equipment.

Cut to the length you need with shears or a utility knife and punch holes for hanging.

Cut these strips to the length you need for hanging in freezer doorways or other cold environments.

Replace worn strips or create a custom door with these individual strips. They completely block light to maintain darkness and privacy.

Sized to fit short openings.

Able to handle temperatures up to 500° F, these door strips can be used near ovens and furnaces.

These strips are ribbed to hide scratches and wear; cut them to length with shears or a utility knife and punch holes for hanging.

Cut these partially light-blocking strips to the length you need and punch holes for hanging.

Swap out damaged mounting plates or make custom strip doors by combining a mounting plate with door strips.

To hide scratches and wear, these doors have ribbed strips.

Create custom doors that allow vehicles and people to move freely, while keeping heated or cooled air in and dirt, dust, and debris out.

Use these doors in data centers and other areas where static build-up could harm sensitive electronics.

These strip doors partially block light.

Set up these free-standing partitions to reflect sound and block noise from traveling to other parts of your facility. A vinyl barrier is sandwiched between two vinyl-coated fiberglass absorbers.

Bolt these valves to flanges. Use them with water, oil, air, and inert gas. All operate on compressed air to automatically divert flow between ports more quickly than motor-driven valves. You must control the air to the actuator using either an electric pilot valve or a manual on/off valve.

The motor on these valves can handle diverting applications with high flow rates and pressures. They operate on electricity to automatically divert flow between ports.

For use with threaded pipe, these valves have NPT connections. Use them with water, oil, air, and inert gas. All operate on compressed air to automatically divert flow between ports more quickly than motor-driven valves. You must control the air to the actuator using either an electric pilot valve or a manual on/off valve.

For a lightweight alternative to metal valves, these have a plastic body. To fit in tight spots, they have a low-profile handle and a short end-to-end length. Valves are for use with water, oil, air, and inert gas. All divert flow between ports.

Designed to direct the flow of liquids in food, dairy, and chemical-processing facilities, these valves can be fully disassembled for clean-out-of-place (COP) processes.

Threads and a hex nut below the handle let you install these valves through instrument panels. They are for use with water, oil, air, and inert gas. All divert flow between ports.

Control flow in two directions from a single source—these valves have two handles for independent operation of each outlet. Use them with water, oil, and inert gas.

For easy installation and removal from pipelines, all ends on these valves have union fittings that disassemble into multiple pieces. Use with water. Valves divert flow between ports.

Also known as shuttle valves, these automatically switch the inlet source as pressure changes; they always direct flow from the higher-pressure side-port inlet to the top-port outlet. Use them with water, oil, air, and inert gas.

A metal body provides more strength and durability than plastic. These valves have a low-profile handle and a short end-to-end length to fit in tight spots. All are for use with water, oil, air, and inert gas. They divert flow between ports.

Bolt these valves to flanges to divert flow between ports in flanged pipelines. They’re for use with water, oil, air, and inert gas.

There’s no need to unbolt these valves for cleaning—remove the handle and slide the valve apart for inline access to internal components. Also known as elliptical valves, they have a fluoroelastomer seal and a polypropylene body for diverting flow in chemical-processing applications.