Place these on top of a machine or table, then relocate them as you see fit. Rigid document protectors allow you to quickly flip through these carousel-style binders. Protectors snap in and out. Each binding holds up to ten protectors.

Multi-document protectors have four clear plastic sleeves attached to single rigid protector, so you can place more documents on your binder.

Index tabs clip onto document protectors to organize your binder.

This binder has three rings for hole punched documents. Screw it to machines, equipment, or walls to mount instructions, literature, or SDS for display and reference.

These binders hold 6" to 18" of pages for displaying reference books and catalogs. For use with three-hole punched documents. They require three-ring or three-post bindings (sold separately). You may attach multiple bindings using the included slide hooks, but cannot exceed the total binding capacity.

3-ring bindings allow better viewing of thick documents.

3-post bindings lock into place when snapped together.

These are thicker and more rigid than standard document protectors.

Protect sets of documents or thick instruction manuals.

Place these holders on a table or counter top, then relocate them as you see fit. They are see-through so you can view contents from any angle.

Slide a sign into either side of these holders for a traditional framed look.

Identify evacuation routes at a glance. Print your evacuation map onto the included transparency film, then expose these map holders to ambient light and the holder will illuminate the sign in the dark. Insert the map from the side. Mount these holders to a flat surface with the included mounting tape.

Adhere the included mounting tape to the center of these holders and then press your sign into place. Holders are sized for use with ADA-Compliant and accessibility signs.

Draw attention to important signs—these holders have a bright border. Insert a sign from the top, bottom, and sides.

Lock the frame to protect signs from tampering. These holders are steel with a scratch- and shatter-resistant acrylic cover, so they will stand up to tough environments will still being optically clear. Insert a sign from the side. Mount them to a wall using the included fasteners. Holders can also be mounted to a pole. Use the mounting slots to attach sign-mounting brackets (sold separately).

Flip the front of the frame open on any side to insert your sign, and then snap the sides closed.

Display signs at a right angle to a wall, shelving, or storage rack. Mount a sign to the panel using tape or adhesive (not included). Holders are sized to fit ADA-compliant and accessibility signs.

Display signs on sidewalks or other areas with high foot traffic, indoors and out. Holders are designed to fit two signs, one on each side. Slide a sign in from the top and down through the two tabs; there is a slot on the bottom to hold the sign in place. Holders fold flat for easy storage.

Carry these boxes from job to job and mount them near valves or electrical controls to save time when organizing group lockouts. Instead of attaching multiple locks to each lockout point, your team can use a single lock to keep equipment powered off. After the lockout keys are placed inside the box, each worker locks their own padlock to the outside. The keys can only be retrieved when each person has finished their task and removed their padlock. These boxes help you comply with OSHA 1910.147 requirements for the control of hazardous energy.

When permits, checklists, or safety information needs to be posted for your job, use lockout boxes with document display. The impact-resistant polycarbonate window is sealed to the box with a gasket that’s rated IPX3, meaning papers are safe from spraying water. A second window lets you check that keys and padlocks are stored and secure. These boxes can be mounted outdoors or in wet environments, and the stainless steel body will not corrode. Mark down permit numbers and other job-specific information on the erasable tag. These boxes also have removable lock caddies and key cups, so you can bring keys and padlocks to lockout points and collect them when you’re done.

Store all of your lockout safety procedure forms in one place. These stations hold binders that you fill with one form for each piece of equipment that lists required lockouts. Mount these stations near equipment you service frequently—the colorful sign reminds you to grab the binder before starting work.

Using these stations helps you create a program for locking out energy sources such as electricity, hydraulics, and steam that adheres to OSHA 1910.147 standards. To keep your procedures current, you can update these forms to reflect changes to equipment.