Wire these receivers directly to your automatic overhead door openers for their power supply.

Replace existing transmitters or team a transmitter and a receiver to remotely operate your automatic overhead door openers.

Pull a chain to manually open overhead doors.

For frequently used doors, these closers last twice as long as standard door closers. They can replace Yale, Dorma, Falcon, Stanley, Parker, and Cal-Royal models with the same mounting hole pattern.

These closers can replace Yale, Dorma, Falcon, Stanley, Parker, and Cal-Royal models with the same mounting hole pattern.

No need to drill new holes—these closers have a mounting plate that fits the hole patterns of most closers from Norton, LCN, Yale, Corbin Russwin, and Dorma.

Save time and money by replacing worn or damaged arms instead of the entire closer.

There's no need to mount a closer to your door or frame—these take the place of an existing hinge pin.

Nudge your door and these openers will open it the rest of the way.

A magnet holds the door open; pull on the door to release.

Push your door open to automatically engage the holder; pull on the door to release.

Step on the spring-operated plunger to hold your door in place; tap on the release lever to free it.

Latch your door to the floor for a secure hold.

Push your door open to automatically engage the holder; pull on the door to release.

Slide these wedges under the door to hold it open.

Small enough to slip into a pocket, these foldable wedges are good for workers who frequently need to prop doors open as they move from job to job. Slide them under the door to hold it open.

These three-way holders can be inserted under the door, over the top corner of the door, or over the hinge pin to hold a door open.

A hydraulic mechanism makes these the smoothest and quietest closers we offer for storm doors.

Use these closers when your door-to-door clearance is limited. They close storm doors more smoothly than standard spring closers.

With a hydraulic mechanism, these are the smoothest and quietest closers we offer for gates.

Springs retract to pull storm doors and gates closed.

Keep environments free of contaminants—with plastic bushings, there's no metal-to-metal contact that can release particles as these supports open and close. Manually control these free-moving lid supports through their full range of motion. Raise the lid until the hold-open mechanism on the support is engaged; slightly lift it again to release the hold and close the lid.

Manually control these standard free-moving lid supports through their full range of motion. Raise or lower the lid until the hold-open mechanism on the support is engaged; slightly lift it again to release the hold and close the lid.

Commonly used on hood and trunk lids, these simple, three-piece rods telescope from 18 1/2" to 46 3/4" to prop lids open at a variety of angles.

No separate hinges are required, these supports act as a hinge and lid support all in one. Springs provide lifting assistance to raise and hold lids open—slightly lift the lid to get it started and the support will do the rest. Manually shut the lids and the supports will hold them in the closed position.

Gradually slow your lid's motion to prevent it from slamming open. To open lids, lower them and the support will slowly and softly do the rest. Manually shut the lids and the supports will hold them in the closed position.

Install these balancers on a vertical frame to suspend, lift, or lower objects that move vertically in a track such as windows, doors, and panels.

Mount these balancers in the corner of a horizontal frame to suspend, lift, or lower objects that move vertically in a track such as windows, doors, and panels.

Fasten these handles directly to the front of your surface to open and close a variety of doors and drawers, including those on furniture, machines, and equipment.

A rubber coating provides a comfortable grip. Cut the grip to the length you need before mounting. Fasten these handles directly to the front of your surface to open and close a variety of doors and drawers, including those on furniture, machines, and equipment.

For applications that require a large gripping area, these handles have a center-to-center distance of 12" or more. Fasten them directly to the front of your surface to open and close a variety of doors and drawers, including those on furniture, machines, and equipment.

These handles provide a stronger connection than those attached with screws or nuts. Use them to open and close a variety of doors and drawers, including those on furniture, machines, and equipment.

With a mounting hole center-to-center distance of 1" or less, these are the smallest pull handles we offer. Thread screws through holes from the back of your surface into the handles to open and close tiny doors and drawers.

Thread screws through holes from the back of your surface into the handles to open and close a variety of doors and drawers, including those on furniture, machines, and equipment.

Add or replace handles on drums and barrels. All of these handles have a curved mounting plate that sits flush against the surface and a folding grip that drops out of the way when you let go. They provide a stronger connection than those attached with screws or nuts.

When not in use, the spring in these handles keeps the folding grip flush with the mounting plate and prevents rattling. Fasten the handles directly to the front of your surface to open and close a variety of doors and drawers on chests, crates, furniture, machines, and equipment.

Fasten these handles directly to the front of your surface to open and close a variety of doors and drawers on chests, crates, furniture, machines, and equipment. Their grip folds out of the way when it's not in use.

Thread screws through holes from the back of your surface into the handles to install. These handles fit into a cutout, so they are flush with the mounting surface. Their grip drops out of the way when you let go. Use them to open and close a variety of doors and drawers on chests, crates, furniture, machines, and equipment.

These handles have a folding grip that drops out of the way when you let go. Insert studs into holes in your surface and secure from the backside to open and close a variety of doors and drawers on chests, crates, furniture, machines, and equipment.

Thread screws through holes from the back of your surface into the handles to open and close a variety of doors and drawers, including those on furniture, machines, and equipment. The grip is offset from the mounting surface so there's room to fully grasp the handle.

With a sanitary design, these threaded-hole knobs are often used to open and close doors and drawers on furniture, machines, and other equipment in pharmaceutical and food-processing facilities.

Thread these sanitary knobs into holes so you can open doors and drawers in hygienic environments.

Create custom threads to secure these handles to the front of your surface from the backside. Use them to open and close a variety of doors and drawers, including those on furniture, machines, and equipment.

Press on the top of the handle grip and it rotates out for use. Often used on hatches and pocket doors, these handles fit into a cutout, so they are flush with the mounting surface. Fasten them directly to the front of the surface.

These handles provide a stronger connection than those attached with screws or nuts. They fit into a cutout, so they are flush with the mounting surface. Use them to open and close a variety of doors and drawers, including those on furniture, machines, and equipment.

Insert studs into holes in your surface and fasten with locknuts from the backside to open and close a variety of doors and drawers, including those on furniture, machines, and equipment. These handles fit into a cutout, so they are flush with the mounting surface.

Operate doors, vents, skylights, and overhead equipment.

Made for use in food processing facilities, these plastic knobs have a metal additive that sets off metal detectors if a piece breaks off into your line.

Made of 304 stainless steel, these touch bars stand up to corrosive environments.

Rugged construction withstands impact from carts, dollies, and other equipment.

Crossbars open doors with a push and are often used on emergency exits.

Hold crossbars in the open position so traffic can pass freely through doorways.

The easy-to-read backlit screen turns on when touched and enters sleep mode when inactive to conserve battery life. Open the outside handle with a combination or the included key; the inside handle is always unlocked.

To gain access from the outside with a key as well as a combination, these handles accept an easy-change lock cylinder. The inside handle is always unlocked.

To gain access from the outside with a key as well as a combination, these handles accept an easy-change lock cylinder. The inside handle is always unlocked.

These handles accept optional HID-compatible proximity cards or key fobs to regulate access for up to 2,000 employees. They are programmable so you can assign different combinations to different people and restrict access when necessary.

For frequently used doors, these handles last twice as long as standard keyed alike self-locking door handles.

These handles are always locked from the outside, but open with a master key and their own keys.

For frequently used doors, these handles last twice as long as standard self-locking door handles.

Use any compatible lock cylinder with these handles. The outside handle is always locked, but you can open the door from the inside.

The outside of these handles is always locked, and can be unlocked with a unique key. The inside handle can always open the door.

Unlock these knobs with a master key and a key unique to that door. They are always locked from the outside, but doors can be opened from the inside knob.

Each of these knobs opens with its own key. The outside handle is always locked, but you can open the door from inside.

In addition to lasting twice as long as standard self-locking door knobs, these are made entirely of corrosion-resistant materials to stand up to washdown and marine environments.

Also known as passage handles, these do not lock.

For frequently used doors, these handles last twice as long as standard door handles.

For frequently used doors, these knobs last twice as long as standard door knobs.

For frequently used doors, these handles last twice as long as standard keyed alike key-and button-locking door handles.

Unlock these handles with a shared master key and a key unique to that door; they lock with a button on the inside handle.

Choose these handles if you want to use your own compatible lock cylinders.

Lock and unlock these handles with a button on the inside or a key on the outside. Handles each open with a different key.

For frequently used doors, these handles last twice as long as standard key- and button-locking door handles.

For frequently used doors, these knobs last twice as long as standard key- and button-locking door knobs.

Open these knobs with both a shared master key and key unique to that door, or use the button on the inside.

For frequently used doors, these handles last twice as long as standard keyed alike key-locking door handles.

These knobs can always be opened from the inside, while the locks on the outside each open with a different key.

For frequently used doors, these knobs last twice as long as standard key-locking door knobs.

Lock and unlock the outside handle with both a master key and a unique door key. The inside handle can always open the door.

Lock and unlock each of these knobs with the same key. The inside knob can always open the door.

In addition to lasting twice as long as standard key-locking door handles, these mortise mount into a cutout in the door to withstand vandalism.

Install your own compatible lock cylinder to lock these knobs from the outside. The inside knob can always open the door.

The locks on these handles open with the same key. They can open from the inside handle whether locked or unlocked.