Center-Groove Dowel Pins
Center-groove pins are often used in place of clevis pins or to create T-handles. The grooves pinch shut when pressed into a hole, creating tension and holding the pin in place. The grooved center locks pins in position, while the smooth ends act as a pivot. For the best fit, the hole should be equal to or slightly larger than the diameter shown. The ends are chamfered for easy insertion. Pins are made of zinc-plated steel for good strength and some corrosion resistance. Breaking strength is measured as double shear, which is the force required to break a pin into three pieces. Also known as type E pins.
For technical drawings and 3-D models, click on a part number.
| Lg. | Dia. (A) | Dia. (A) Tolerance | Dia. (B) | Dia. (B) Tolerance | Groove Lg. | Breaking Strength, lbs. | Pkg. Qty. | Pkg. | |
Zinc-Plated 1117 Carbon Steel, Zinc-Plated 1215 Carbon Steel | |||||||||
|---|---|---|---|---|---|---|---|---|---|
3/32" Dia. | |||||||||
| 1/4" | 0.094" | -0.002" to 0" | 0.101" | -0.003" to 0.003" | 1/8" | 850 | 25 | 000000000 | 000000 |
| 1/2" | 0.094" | -0.002" to 0" | 0.101" | -0.003" to 0.003" | 1/4" | 850 | 25 | 000000000 | 00000 |
Half-Groove Dowel Pins
These pins make good hinges or pivots. The grooves pinch shut when pressed into a hole, creating tension and holding the pin in place. The grooved half locks pins in position, while the smooth half acts as a pivot. For the best fit, the hole should be equal to or slightly larger than the diameter shown. The ends are chamfered for easy insertion. Pins are made of zinc-plated steel for good strength and some corrosion resistance. Breaking strength is measured as double shear, which is the force required to break a pin into three pieces. Also known as type H pins.
For technical drawings and 3-D models, click on a part number.
Full-Groove Dowel Pins
Grooves run the full length of these pins for a firm hold that won't spin. Use them in place of standard dowel, spring, and taper pins to fasten parts. The three grooves pinch shut when pressed into a hole, creating tension to lock pins in place. For the best fit, the hole should be equal to or slightly larger than the diameter shown. The ends are chamfered for easy insertion. Breaking strength is measured as double shear, which is the force required to break a pin into three pieces. Also known as type A pins.
Pins with tapered grooves are easier to install than pins with parallel grooves, but more likely to loosen from vibration. Zinc-plated steel pins have good strength and some corrosion resistance.
18-8 stainless steel pins offer a balance of strength and corrosion resistance. They may be mildly magnetic. Pins are passivated for added protection against corrosion and oxidation.
For technical drawings and 3-D models, click on a part number.
Half-Groove Dowel Pins with Notch
These pins are commonly used as anchors for tension springs. The grooved half locks pins in position, and spring ends fit in to the notch. The grooves pinch shut when pressed into a hole, creating tension and holding the pin in place. For the best fit, the hole should be equal to or slightly larger than the diameter shown. The ends are rounded for easy insertion. Pins are made of zinc-plated steel for good strength and some corrosion resistance. Breaking strength is measured as double shear, which is the force required to break a pin into three pieces. Also known as type G pins.
For technical drawings and 3-D models, click on a part number.
Quarter-Groove Dowel Pins
Quarter-groove pins are well suited for hinges or pivots. The grooves pinch shut when pressed into a hole, creating tension and holding the pin in place. The grooved end locks pins in position, while the smooth portion acts as a pivot. For the best fit, the hole should be equal to or slightly larger than the diameter shown. The ends are chamfered for easy insertion. Pins are made of zinc-plated steel for good strength and some corrosion resistance. Breaking strength is measured as double shear, which is the force required to break a pin into three pieces. Also known as type C pins.
For technical drawings and 3-D models, click on a part number.
Core Pins
Mold plastic around these pins to form small holes, or use them to perforate parts. They have a flat head to fit into a counterbored hole. Pins can be machined to fit your application. They're precision-ground to tight tolerances. Made of M2 tool steel, these pins are wear resistant and stay sharp at high temperatures.
For technical drawings and 3-D models, click on a part number.
Ejector Pins
Also known as knockout and forged pins, use these pins to push parts out of molds. Pins are precision-ground to tight tolerances and hardened for strength and wear resistance. Machining is not recommended.
M2 tool steel pins withstand high temperatures.
For technical drawings and 3-D models, click on a part number.
Head | 6" Lg. | |||||
|---|---|---|---|---|---|---|
| Dia. | Dia. Tolerance | Dia. | Ht. | Min. Hardness | Each | |
| 0.0940" | -0.0003" to 0" | 1/4" | 1/8" | Rockwell C60 | 000000000 | 000000 |