System of Measurement System of Measurement |
|---|
|
Diameter Diameter | Show |
|---|
|
Diameter Diameter | Hide |
|---|
Length Length |
|---|
Material Material |
|---|
|
Tolerance Rating Tolerance Rating |
|---|
|
Specifications Met Specifications Met |
|---|
|
Minimum Hardness Minimum Hardness |
|---|
|
End Type End Type |
|---|
 | Plain |
Breaking Strength Breaking Strength |
|---|
|
|
Passivation Passivation |
|---|
|
For Hole Diameter For Hole Diameter |
|---|
|
PEM® Part Number PEM® Part Number |
|---|
|
For Minimum Panel Thickness For MinimumPanel Thickness |
|---|
|
Head Diameter Head Diameter |
|---|
|
Head Height Head Height |
|---|
|
Dowel Pins
Use dowel pins as pivots, hinges, shafts, jigs, and fixtures to locate or hold parts. For a tight fit, your hole should be equal to or slightly smaller than the diameter shown. Breaking strength is measured as double shear, which is the force required to break a pin into three pieces.
Steel pins are the strongest dowel pins. Steel pins are precision ground except for 1/32" diameter pins. Stainless steel pins are more corrosion resistant than steel pins. Pins that are passivated offer added protection against corrosion and oxidation. Stainless steel pins are precision ground except for 1/64" diameter pins. 18-8 stainless steel pins offer a balance of strength and corrosion resistance. They may be mildly magnetic. 316 stainless steel pins have the best corrosion resistance of our stainless steel pins. They may be mildly magnetic.
Metric pins meet either DIN 6325-m6 specifications for steel pins or ISO 2338-m6 specifications for stainless steel pins. DIN 6325-m6 is functionally equivalent to DIN EN ISO 8734, with slight differences in hardness and length tolerances.
DIN 7 is no longer an active specification and is superseded by ISO 2338-m6. They are functionally equivalent with slight differences in length and the pin ends. DIN 7 has rounded ends where ISO 2338-m6 has chamfered ends.
For technical drawings and 3-D models, click on a part number.
| Lg., mm | Dia. Tolerance, mm | Min. Hardness | Breaking Strength | Specifications Met | Pkg. Qty. | Pkg. | |
5 mm Dia. | |||||||
|---|---|---|---|---|---|---|---|
| 5 | 0.004 to 0.012 | Rockwell C52 | Not Rated | DIN 6325-m6, DIN EN ISO 8734 | 5 | 000000000 | 00000 |
| 6 | 0.004 to 0.012 | Rockwell C52 | Not Rated | DIN 6325-m6, DIN EN ISO 8734 | 5 | 000000000 | 0000 |
| 7 | 0.004 to 0.012 | Rockwell C52 | Not Rated | DIN 6325-m6, DIN EN ISO 8734 | 5 | 000000000 | 0000 |
| 9 | 0.004 to 0.012 | Rockwell C52 | Not Rated | DIN 6325-m6, DIN EN ISO 8734 | 5 | 000000000 | 0000 |
| 34 | 0.004 to 0.012 | Rockwell C52 | Not Rated | DIN 6325-m6, DIN EN ISO 8734 | 1 | 000000000 | 0000 |
| 38 | 0.004 to 0.012 | Rockwell C52 | Not Rated | DIN 6325-m6, DIN EN ISO 8734 | 1 | 000000000 | 0000 |
| Lg., mm | Dia. Tolerance, mm | Min. Hardness | Breaking Strength, lbs. | Specifications Met | Pkg. Qty. | Pkg. | |
5 mm Dia. | |||||||
|---|---|---|---|---|---|---|---|
| 8 | 0.004 to 0.012 | Rockwell C52 | 4,600 | DIN 6325-m6, DIN EN ISO 8734 | 25 | 000000000 | 00000 |
| 10 | 0.004 to 0.012 | Rockwell C52 | 4,600 | DIN 6325-m6, DIN EN ISO 8734 | 25 | 000000000 | 0000 |
| 12 | 0.004 to 0.012 | Rockwell C52 | 4,600 | DIN 6325-m6, DIN EN ISO 8734 | 50 | 000000000 | 00000 |
| 14 | 0.004 to 0.012 | Rockwell C52 | 4,600 | DIN 6325-m6, DIN EN ISO 8734 | 50 | 000000000 | 00000 |
| 16 | 0.004 to 0.012 | Rockwell C52 | 4,600 | DIN 6325-m6, DIN EN ISO 8734 | 50 | 000000000 | 00000 |
| 18 | 0.004 to 0.012 | Rockwell C52 | 4,600 | DIN 6325-m6, DIN EN ISO 8734 | 50 | 000000000 | 00000 |
| 20 | 0.004 to 0.012 | Rockwell C52 | 4,600 | DIN 6325-m6, DIN EN ISO 8734 | 25 | 000000000 | 0000 |
| 22 | 0.004 to 0.012 | Rockwell C52 | 4,600 | DIN 6325-m6, DIN EN ISO 8734 | 25 | 000000000 | 0000 |
| 24 | 0.004 to 0.012 | Rockwell C52 | 4,600 | DIN 6325-m6, DIN EN ISO 8734 | 25 | 000000000 | 0000 |
| 26 | 0 to 0.012 | Rockwell C58 | 4,600 | DIN 6325-m6, DIN EN ISO 8734 | 25 | 000000000 | 0000 |
| 28 | 0.004 to 0.012 | Rockwell C52 | 4,600 | DIN 6325-m6, DIN EN ISO 8734 | 25 | 000000000 | 0000 |
| 30 | 0.004 to 0.012 | Rockwell C52 | 4,600 | DIN 6325-m6, DIN EN ISO 8734 | 25 | 000000000 | 00000 |
| 32 | 0.004 to 0.012 | Rockwell C52 | 4,600 | DIN 6325-m6, DIN EN ISO 8734 | 25 | 000000000 | 00000 |
| 36 | 0.004 to 0.012 | Rockwell C52 | 4,600 | DIN 6325-m6, DIN EN ISO 8734 | 25 | 000000000 | 00000 |
| 40 | 0.004 to 0.012 | Rockwell C52 | 4,600 | DIN 6325-m6, DIN EN ISO 8734 | 25 | 000000000 | 00000 |
| 45 | 0.004 to 0.012 | Rockwell C52 | 4,600 | DIN 6325-m6, DIN EN ISO 8734 | 25 | 000000000 | 00000 |
| 50 | 0.004 to 0.012 | Rockwell C52 | 4,600 | DIN 6325-m6, DIN EN ISO 8734 | 10 | 000000000 | 0000 |
| 60 | 0.004 to 0.012 | Rockwell C52 | 4,600 | DIN 6325-m6, DIN EN ISO 8734 | 10 | 000000000 | 00000 |
| 70 | 0.004 to 0.012 | Rockwell C52 | 4,600 | DIN 6325-m6, DIN EN ISO 8734 | 5 | 000000000 | 00000 |
| 80 | 0 to 0.012 | Rockwell C58 | 4,600 | DIN 6325-m6, DIN EN ISO 8734 | 5 | 000000000 | 0000 |
| Lg., mm | Dia. Tolerance, mm | Min. Hardness | Breaking Strength | Passivation | Specifications Met | Pkg. Qty. | Pkg. | |
5 mm Dia. | ||||||||
|---|---|---|---|---|---|---|---|---|
| 5 | 0 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 10 | 000000000 | 00000 |
| 6 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 25 | 000000000 | 0000 |
| 7 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 5 | 000000000 | 0000 |
| 8 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 25 | 000000000 | 0000 |
| 9 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 5 | 000000000 | 0000 |
| 10 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 25 | 000000000 | 0000 |
| 12 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 25 | 000000000 | 00000 |
| 14 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 25 | 000000000 | 00000 |
| 16 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 25 | 000000000 | 00000 |
| 18 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 25 | 000000000 | 00000 |
| 20 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 25 | 000000000 | 00000 |
| 22 | 0 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 10 | 000000000 | 0000 |
| 24 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 25 | 000000000 | 00000 |
| 26 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 5 | 000000000 | 0000 |
| 28 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 25 | 000000000 | 00000 |
| 30 | 0 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 10 | 000000000 | 0000 |
| 32 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 10 | 000000000 | 0000 |
| 34 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 1 | 000000000 | 0000 |
| 36 | 0 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 10 | 000000000 | 0000 |
| 38 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 1 | 000000000 | 0000 |
| 40 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 10 | 000000000 | 0000 |
| 45 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 10 | 000000000 | 00000 |
| 50 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 10 | 000000000 | 00000 |
| 60 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 1 | 000000000 | 0000 |
| 80 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 1 | 000000000 | 0000 |
| 100 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 1 | 000000000 | 0000 |
| Lg., mm | Dia. Tolerance, mm | Min. Hardness | Breaking Strength | Passivation | Specifications Met | Pkg. Qty. | Pkg. | |
5 mm Dia. | ||||||||
|---|---|---|---|---|---|---|---|---|
| 5 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 5 | 000000000 | 00000 |
| 6 | 0 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 5 | 000000000 | 0000 |
| 7 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 5 | 000000000 | 0000 |
| 8 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 10 | 000000000 | 0000 |
| 9 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 5 | 000000000 | 0000 |
| 10 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 10 | 000000000 | 0000 |
| 12 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 10 | 000000000 | 0000 |
| 14 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 10 | 000000000 | 0000 |
| 16 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 10 | 000000000 | 0000 |
| 18 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 10 | 000000000 | 0000 |
| 20 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 10 | 000000000 | 0000 |
| 22 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 1 | 000000000 | 0000 |
| 24 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 5 | 000000000 | 0000 |
| 26 | 0 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 5 | 000000000 | 0000 |
| 28 | 0 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 5 | 000000000 | 0000 |
| 30 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 5 | 000000000 | 0000 |
| 32 | 0 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 5 | 000000000 | 0000 |
| 34 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 1 | 000000000 | 0000 |
| 36 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 5 | 000000000 | 0000 |
| 38 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 1 | 000000000 | 0000 |
| 40 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 5 | 000000000 | 0000 |
| 50 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 5 | 000000000 | 0000 |
| 60 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 1 | 000000000 | 0000 |
| 80 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 1 | 000000000 | 0000 |
| 100 | 0.004 to 0.012 | Not Rated | Not Rated | Passivated | DIN 7, ISO 2338-m6 | 1 | 000000000 | 0000 |
Undersized Dowel Pins
Slip these pins in and out during maintenance or prototyping—they’re undersized to make alignment easier. Unlike standard pins, which fit tightly inside holes, these are designed to give you some wiggle room. Chamfered ends make them easier to insert. The breaking strength listed is double shear, which is the amount of force required to break a pin into three pieces.
Steel pins are very strong. They are best for dry environments.
18-8 stainless steel pins can be used in wet and humid environments without rusting, but they are not as strong as steel.
All metric pins meet ISO 2338-h8, which means they adhere to international standards for dimensions and tolerances.
For technical drawings and 3-D models, click on a part number.
Ejector Pins
Also known as knockout and forged pins, use these pins to push parts out of molds. Pins are precision-ground to tight tolerances and hardened for strength and wear resistance. Machining is not recommended.
M2 tool steel pins withstand high temperatures.
Metric pins meet DIN 1530 specifications.
For technical drawings and 3-D models, click on a part number.
Head | ||||||
|---|---|---|---|---|---|---|
| Dia., mm | Dia. Tolerance, mm | Dia., mm | Ht., mm | Min. Hardness | Each | |
100 mm Lg. | ||||||
| 5.0000 | -0.012 to -0.004 | 10 | 3 | Rockwell C60 | 000000000 | 000000 |
125 mm Lg. | ||||||
| 5.0000 | -0.012 to -0.004 | 10 | 3 | Rockwell C60 | 000000000 | 00000 |
160 mm Lg. | ||||||
| 5.0000 | -0.012 to -0.004 | 10 | 3 | Rockwell C60 | 000000000 | 00000 |
200 mm Lg. | ||||||
| 5.0000 | -0.012 to -0.004 | 10 | 3 | Rockwell C60 | 000000000 | 00000 |
250 mm Lg. | ||||||
| 5.0000 | -0.012 to -0.004 | 10 | 3 | Rockwell C60 | 000000000 | 00000 |
Slotted Spring Pins
Also known as roll, tension, split, and expansion pins, these pins have a slot along one side that you squeeze closed to install them into unthreaded holes. Once installed, they expand slightly, creating outward tension that holds them tight against the hole wall. These pins absorb shock and vibration in your system, and keep parts from loosening. They are often used as hinge pins, or to hold springs and power transmission components in place.
Install these pins into a hole slightly smaller than the pin diameter. They have at least one chamfered end, which means the end is angled to make insertion easier.
Breaking strength is measured as double shear, which is the amount of force required to break a pin into three pieces.
Some metric pins with the same diameter come in two different wall thicknesses. Thinner walls are more flexible, easier to install, and won’t weigh down your assembly as much as thicker pins. Layer a pin with a thin wall inside a pin with a thicker wall to increase the breaking strength. Make sure the slots are opposite one another for maximum strength.
Steel pins are strong and wear resistant.
18-8 stainless steel pins offer a balance of strength and corrosion resistance.
Passivated pins offer added protection against corrosion and oxidation.
Pins that meet specifications for ISO 8752 (formerly DIN 1481) or ISO 13337 (formerly DIN 7346) adhere to international standards for pin dimensions.
For technical drawings and 3-D models, click on a part number.
| Lg., mm | For Hole Dia., mm | Wall Thick., mm | Min. Hardness | Breaking Strength, lbs. | Specifications Met | Pkg. Qty. | Pkg. | |
5 mm Dia. | ||||||||
|---|---|---|---|---|---|---|---|---|
| 5 | 5 | 0.5 | Rockwell C42 | 2,300 | DIN 7346, ISO 13337 | 50 | 000000000 | 000000 |
| 6 | 5 | 0.5 | Rockwell C42 | 2,300 | DIN 7346, ISO 13337 | 50 | 000000000 | 00000 |
| 8 | 5 | 0.5 | Rockwell C42 | 2,300 | DIN 7346, ISO 13337 | 50 | 000000000 | 0000 |
| 10 | 5-5.2 | 1 | Rockwell C42 | 3,900 | DIN 1481, ISO 8752 | 100 | 000000000 | 0000 |
| 12 | 5 | 0.5 | Rockwell C42 | 2,300 | DIN 7346, ISO 13337 | 25 | 000000000 | 0000 |
| 12 | 5-5.2 | 1 | Rockwell C42 | 3,900 | ISO 8752 | 100 | 000000000 | 0000 |
| 14 | 5 | 0.5 | Rockwell C42 | 2,300 | DIN 7346, ISO 13337 | 50 | 000000000 | 00000 |
| 14 | 5-5.2 | 1 | Rockwell C42 | 3,900 | ISO 8752 | 100 | 000000000 | 0000 |
| 16 | 5 | 0.5 | Rockwell C42 | 2,300 | DIN 7346, ISO 13337 | 50 | 000000000 | 0000 |
| 16 | 5-5.2 | 1 | Rockwell C42 | 3,900 | ISO 8752 | 100 | 000000000 | 0000 |
| 18 | 5 | 0.5 | Rockwell C42 | 2,300 | DIN 7346, ISO 13337 | 50 | 000000000 | 0000 |
| 18 | 5-5.2 | 1 | Rockwell C42 | 3,900 | ISO 8752 | 100 | 000000000 | 0000 |
| 20 | 5 | 0.5 | Rockwell C42 | 2,300 | DIN 7346, ISO 13337 | 50 | 000000000 | 00000 |
| 20 | 5-5.2 | 1 | Rockwell C42 | 3,900 | ISO 8752 | 100 | 000000000 | 0000 |
| 22 | 5 | 0.5 | Rockwell C42 | 2,300 | DIN 7346, ISO 13337 | 50 | 000000000 | 00000 |
| 22 | 5-5.2 | 1 | Rockwell C42 | 3,900 | ISO 8752 | 100 | 000000000 | 0000 |
| 24 | 5 | 0.5 | Rockwell C42 | 2,300 | DIN 7346, ISO 13337 | 50 | 000000000 | 00000 |
| 24 | 5-5.2 | 1 | Rockwell C42 | 3,900 | ISO 8752 | 100 | 000000000 | 0000 |
| 26 | 5 | 0.5 | Rockwell C42 | 2,300 | DIN 7346, ISO 13337 | 50 | 000000000 | 00000 |
| 26 | 5-5.2 | 1 | Rockwell C42 | 3,900 | ISO 8752 | 100 | 000000000 | 0000 |
| 28 | 5 | 0.5 | Rockwell C42 | 2,300 | DIN 7346, ISO 13337 | 50 | 000000000 | 00000 |
| 28 | 5-5.2 | 1 | Rockwell C42 | 3,900 | ISO 8752 | 100 | 000000000 | 00000 |
| 30 | 5 | 0.5 | Rockwell C42 | 2,300 | DIN 7346, ISO 13337 | 50 | 000000000 | 00000 |
| 30 | 5-5.2 | 1 | Rockwell C42 | 3,900 | ISO 8752 | 100 | 000000000 | 00000 |
| 32 | 5 | 0.5 | Rockwell C42 | 2,300 | DIN 7346, ISO 13337 | 25 | 000000000 | 0000 |
| 32 | 5-5.2 | 1 | Rockwell C42 | 3,900 | ISO 8752 | 100 | 000000000 | 00000 |
| 36 | 5 | 0.5 | Rockwell C42 | 2,300 | DIN 7346, ISO 13337 | 25 | 000000000 | 0000 |
| 36 | 5-5.2 | 1 | Rockwell C42 | 3,900 | ISO 8752 | 100 | 000000000 | 00000 |
| 40 | 5 | 0.5 | Rockwell C42 | 2,300 | DIN 7346, ISO 13337 | 25 | 000000000 | 0000 |
| 40 | 5-5.2 | 1 | Rockwell C42 | 3,900 | ISO 8752 | 100 | 000000000 | 00000 |
| 45 | 5 | 0.5 | Rockwell C42 | 2,300 | DIN 7346, ISO 13337 | 25 | 000000000 | 0000 |
| 45 | 5-5.2 | 1 | Rockwell C42 | 3,900 | ISO 8752 | 100 | 000000000 | 00000 |
| 50 | 5 | 0.5 | Rockwell C42 | 2,300 | DIN 7346, ISO 13337 | 25 | 000000000 | 0000 |
| 50 | 5-5.2 | 1 | Rockwell C42 | 3,900 | ISO 8752 | 50 | 000000000 | 0000 |
| 60 | 5 | 0.5 | Rockwell C42 | 2,300 | DIN 7346, ISO 13337 | 25 | 000000000 | 00000 |
| 70 | 5 | 0.5 | Rockwell C42 | 2,300 | DIN 7346, ISO 13337 | 10 | 000000000 | 0000 |
| 80 | 5 | 0.5 | Rockwell C42 | 2,300 | DIN 7346, ISO 13337 | 10 | 000000000 | 0000 |
| Lg., mm | For Hole Dia., mm | Wall Thick., mm | Min. Hardness | Breaking Strength | Passivation | Specifications Met | Pkg. Qty. | Pkg. | |
5 mm Dia. | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| 10 | 5-5.2 | 1 | Not Rated | Not Rated | Passivated | DIN 1481, ISO 8752 | 10 | 000000000 | 00000 |
| 12 | 5-5.2 | 1 | Not Rated | Not Rated | Passivated | DIN 1481, ISO 8752 | 10 | 000000000 | 0000 |
| 14 | 5-5.2 | 1 | Not Rated | Not Rated | Not Passivated | ISO 8752 | 10 | 000000000 | 0000 |
| 16 | 5-5.2 | 1 | Not Rated | Not Rated | Passivated | DIN 1481, ISO 8752 | 10 | 000000000 | 0000 |
| 18 | 5-5.2 | 1 | Not Rated | Not Rated | Not Passivated | ISO 8752 | 10 | 000000000 | 0000 |
| 20 | 5-5.2 | 1 | Not Rated | Not Rated | Passivated | DIN 1481, ISO 8752 | 10 | 000000000 | 0000 |
| 22 | 5-5.2 | 1 | Not Rated | Not Rated | Passivated | DIN 1481, ISO 8752 | 10 | 000000000 | 0000 |
| 24 | 5-5.2 | 1 | Not Rated | Not Rated | Passivated | DIN 1481, ISO 8752 | 10 | 000000000 | 0000 |
| 26 | 5-5.2 | 1 | Not Rated | Not Rated | Passivated | DIN 1481, ISO 8752 | 10 | 000000000 | 0000 |
| 28 | 5-5.2 | 1 | Not Rated | Not Rated | Not Passivated | ISO 8752 | 10 | 000000000 | 0000 |
| 30 | 5-5.2 | 1 | Not Rated | Not Rated | Passivated | DIN 1481, ISO 8752 | 10 | 000000000 | 0000 |
| 32 | 5-5.2 | 1 | Not Rated | Not Rated | Not Passivated | ISO 8752 | 10 | 000000000 | 0000 |
| 36 | 5-5.2 | 1 | Not Rated | Not Rated | Passivated | DIN 1481, ISO 8752 | 10 | 000000000 | 0000 |
| 40 | 5-5.2 | 1 | Not Rated | Not Rated | Passivated | DIN 1481, ISO 8752 | 10 | 000000000 | 0000 |
| 45 | 5-5.2 | 1 | Not Rated | Not Rated | Not Passivated | ISO 8752 | 10 | 000000000 | 0000 |
| 50 | 5-5.2 | 1 | Not Rated | Not Rated | Passivated | DIN 1481, ISO 8752 | 10 | 000000000 | 0000 |
Coiled Spring Pins
These spiral pins remain flexible after installation, so they absorb shock and vibration better than slotted spring pins. They work well in holes that are out of round. Use them for fastening, pivoting, and holding.
Squeeze pins closed and install them in a hole slightly smaller than the pin. Tension holds them tight against the hole wall. The chamfered ends aid insertion.
Breaking strength is measured as double shear, which is the force required to break a pin into three pieces.
Steel pins offer good strength.
18-8 stainless steel pins resist corrosion better than 420 stainless steel pins. They may be mildly magnetic.
Passivated pins offer added protection against corrosion and oxidation.
Metric pins meet ISO 8750 specifications.
For technical drawings and 3-D models, click on a part number.
| Lg. | For Hole Dia. | Min. Hardness | Breaking Strength, lbs. | Passivation | Specifications Met | Pkg. Qty. | Pkg. | |
Metric 1050-1095 Spring Steel | ||||||||
|---|---|---|---|---|---|---|---|---|
5mm Dia. | ||||||||
| 12mm | 5mm-5.1mm | Rockwell C43 | 3,300 | __ | DIN 7343, ISO 8750 | 25 | 000000000 | 00000 |
| 20mm | 5mm-5.1mm | Rockwell C43 | 3,300 | __ | DIN 7343, ISO 8750 | 25 | 000000000 | 0000 |
| 30mm | 5mm-5.1mm | Rockwell C43 | 3,300 | __ | DIN 7343, ISO 8750 | 25 | 000000000 | 00000 |
| 35mm | 5mm-5.1mm | Rockwell C43 | 3,300 | __ | DIN 7343, ISO 8750 | 25 | 000000000 | 00000 |
| 40mm | 5mm-5.1mm | Rockwell C43 | 3,300 | __ | DIN 7343, ISO 8750 | 10 | 000000000 | 0000 |
Metric 18-8 Stainless Steel | ||||||||
5mm Dia. | ||||||||
| 12mm | 5mm-5.1mm | Not Rated | 2,500 | Passivated | DIN 7343, ISO 8750 | 10 | 000000000 | 0000 |
| 20mm | 5mm-5.1mm | Not Rated | 2,500 | Passivated | DIN 7343, ISO 8750 | 10 | 000000000 | 0000 |
| 30mm | 5mm-5.1mm | Not Rated | 2,500 | Passivated | DIN 7343, ISO 8750 | 5 | 000000000 | 0000 |
| 35mm | 5mm-5.1mm | Not Rated | 2,500 | Passivated | DIN 7343, ISO 8750 | 5 | 000000000 | 0000 |
| 40mm | 5mm-5.1mm | Not Rated | 2,500 | Passivated | DIN 7343, ISO 8750 | 5 | 000000000 | 0000 |
Captive Pins
Also known as pilot pins, use these pins to position, pivot, and align components. To install, punch or drill a hole in sheet metal, then use a punch and anvil or arbor press to clinch the head to the metal.
Pins are passivated for added protection against corrosion and oxidation. The ends are chamfered for easy insertion.
PEM® TPS pins work on steel or aluminum sheets. Made of 18-8 stainless steel, they offer a balance of strength and corrosion resistance and may be mildly magnetic.
PEM® TP4 pins work on stainless steel sheets. Made of 400 series stainless steel, they resist wear and abrasion, but are not as corrosion resistant as 18-8 stainless steel pins. Pins may be mildly magnetic.
For technical drawings and 3-D models, click on a part number.
| Lg. | Dia. Tolerance | PEM® Part No. | For Min. Panel Thick. | Pkg. Qty. | Pkg. | |
Metric 18-8 Stainless Steel | ||||||
|---|---|---|---|---|---|---|
5mm Dia. | ||||||
| 10mm | -0.05mm to 0.05mm | TPS-5MM-10 | 1mm | 25 | 000000000 | 00000 |
| 12mm | -0.05mm to 0.05mm | TPS-5MM-12 | 1mm | 25 | 000000000 | 0000 |
| 16mm | -0.05mm to 0.05mm | TPS-5MM-16 | 1mm | 25 | 000000000 | 0000 |
| 20mm | -0.05mm to 0.05mm | TPS-5MM-20 | 1mm | 25 | 000000000 | 00000 |
Metric 400 Series Stainless Steel | ||||||
5mm Dia. | ||||||
| 10mm | -0.05mm to 0.05mm | TP4-5MM-10 | 1mm | 25 | 000000000 | 0000 |
| 12mm | -0.05mm to 0.05mm | TP4-5MM-12 | 1mm | 25 | 000000000 | 00000 |
| 16mm | -0.05mm to 0.05mm | TP4-5MM-16 | 1mm | 25 | 000000000 | 00000 |
| 20mm | -0.05mm to 0.05mm | TP4-5MM-20 | 1mm | 25 | 000000000 | 00000 |