Plastic pins are a nonconductive and nonmagnetic alternative to metal dowel pins. Use them as pivots, hinges, shafts, jigs, and fixtures to locate or hold parts.

Oversized to fit worn and enlarged holes, these pins work well as repair and replacement parts.

To remove these pins, thread a screw or tool into the tapped hole, then pull them out.

A spiral groove cut into these pins relieves trapped air but stays in 360° contact with the hole for a secure fit that's easy to insert in and remove from blind holes. To remove, thread a screw or tool into the tapped hole, then pull the pin out.

These pins make good hinges or pivots. The grooved half locks pins in position, while the smooth half can act as a pivot. Also known as type H pins.

Center-groove pins are often used in place of clevis pins or to create T-handles. The grooved center locks pins in position, while the smooth ends act as a pivot. Also known as type E pins.

Quarter-groove pins are well suited for hinges or pivots. The grooved end locks pins in position, while the smooth portion can act as a pivot. Also known as type C pins.

Use these as pivot or hinge pins. The knurled half locks pins in position, while the smooth half acts as a pivot.

Center-knurled pins are often used in place of clevis pins or to create T-handles. The knurled center locks pins in position, while the smooth ends act as a pivot.

Barbs bite into plastics and soft metals such as aluminum for a strong hold, and a round head gives a finished appearance.

Pass wires and other components through these hollow pins.

These pins have a flat head to fit into a counterbored hole.

Push parts out of molds with these hardened pins. Also known as knockout and forged pins.

Use these pins with a die to punch 3/16" and larger holes. Pins can be modified to fit your application.

Interlocking teeth help these pins resist sliding when exposed to vibration. They have a slot that presses closed when the pins are inserted so they don't flex after installation.

For tough jobs, these spiral pins are 30% stronger than our standard coiled spring pins. They remain flexible after installation to absorb shock and vibration, and work well in holes that are out of round.

Threads on these pins stick out for easy removal from blind holes. Tighten the hex nut to draw the pin out.

Position, pivot, and align components. Also known as pilot pins and PEM® TP4, TPS, and MPP pins.

Create a custom headed pin with your choice of material, dimensions, and end type.

Weld these pins directly to a surface —no mounting hole required.

Screw the threaded end of these metric studs into a tapped hole and use the unthreaded end as a pivot point, hinge, shaft, or locator pin.

Slotted spring pins are also known as roll, tension, split, and expansion pins. Because the slot is pressed closed when the pins are inserted, they don't flex after installation.

Maintain consistent alignment in mating parts by installing a pin in one part and a liner in the other.

Screw the shank into a threaded hole for quick installation and removal.

Encase these pins while molding plastic or composite parts. Once set, the knurls resist movement, letting you align the workpiece with precision on a plate or table.

When locating a workpiece using through-hole alignment pins, use one of these bushings and one standard bushing to prevent the pins from binding in your fixture.

Use the handle on these retractors to extend and retract a locating pin, protecting the pin from damage in applications where fixtures move through a process, such as along a conveyor belt.

Mount through the counterbored hole with a socket head cap screw to support and position workpieces and fixtures from the bottom or side.

Support rounded or irregularly shaped workpieces from the bottom or side with minimal contact.

Sealed at the top to prevent debris from getting inside and making them seize up, these guide pins are a good choice for machining fixtures.

Threading makes these guide pins easier to remove and replace than press fit, so they're useful for high-wear applications.

As the face of these plungers is pushed in, the internal spring applies outward pressure to hold a workpiece in position against stops and rails.

When one side wears out, use the other one. Also known as barrel drift pins.

These brass tools reduce marring on metal surfaces because they're softer than steel punches.

When one side wears out, use the other one.

The tapered shaft of these pins eliminates the need for hammering and prying when aligning flange bolt holes.

Use alignment pins to align structural components such as I-beams and angle iron for bolting, riveting, and welding.