System of Measurement System of Measurement |
|---|
|
Material Material |
|---|
|
End Shape End Shape |
|---|
 | Chamfered |
Pin Type Pin Type |
|---|
 | Dowel |
Shaft Type Shaft Type |
|---|
 | Plain |
Head Type Head Type |
|---|
 | Tapped |
Tolerance Rating Tolerance Rating |
|---|
|
End Type End Type |
|---|
 | Plain |
Minimum Hardness Minimum Hardness |
|---|
|
Breaking Strength Breaking Strength |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (DefenseAcquisition Regulations Supplement)  |
|---|
Thread Size Thread Size | Show |
|---|
Thread Size Thread Size | Hide |
|---|
Thread Pitch Thread Pitch |
|---|
Shaft Diameter Shaft Diameter |
|---|
|
Thread Type Thread Type |
|---|
|
Thread Spacing Thread Spacing |
|---|
Hardness Hardness |
|---|
|
Tensile Strength Tensile Strength |
|---|
|
About Threaded Studs and Rods
More
Pull-Out Dowel Pins
One end of these pins is tapped, and the other is chamfered for easy insertion. To remove, thread a screw or tool into the tapped hole, then pull the pin out. Because they aren't vented, they work best in through holes. Use them as pivots, hinges, shafts, jigs, and fixtures to locate or hold parts. Pins are precision ground for accurate alignment. Breaking strength is measured as double shear, which is the force required to break a pin into three pieces.
Metric pins meet DIN 7979D-m6 specifications.
Steel pins have good strength.
For technical drawings and 3-D models, click on a part number.
Thread | ||||||||
|---|---|---|---|---|---|---|---|---|
| Lg., mm | Dia. Tolerance, mm | Size | Pitch, mm | Min. Hardness | Breaking Strength, lbs. | Specifications Met | Each | |
20 mm Dia. | ||||||||
| 50 | 0.008 to 0.021 | M10 | 1.5 | Rockwell C52 | 51,500 | DIN 7979D-m6 | 000000000 | 00000 |
| 60 | 0.008 to 0.021 | M10 | 1.5 | Rockwell C52 | 51,500 | DIN 7979D-m6 | 000000000 | 00000 |
| 80 | 0.008 to 0.021 | M10 | 1.5 | Rockwell C52 | 51,500 | DIN 7979D-m6 | 000000000 | 00000 |
Use with internally threaded dowel pins. A complete tool requires a puller handle and a tip that fits your pin. You’ll also need a socket head cap screw that can thread into the pin. To use, thread a tip into the puller handle and fit the other end of the tip over the screw. Slide the weight along the handle to push or pull.
Metric Partially Threaded Studs
Screw the threaded end of these metric studs into a tapped hole and use the unthreaded end as a pivot point, hinge, shaft, or locator pin. All can be installed and adjusted by hand or with a slotted screwdriver. These studs are steel for strength and wear resistance. They’re best for dry environments, since moisture will cause them to rust. All meet ISO 2342 (formerly DIN 427), an international standard for fastener dimensions.
For technical drawings and 3-D models, click on a part number.
Shaft | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| Lg., mm | Thread Lg., mm | Lg., mm | Dia., mm | Dia. Tolerance, mm | Tensile Strength | Hardness | Drive Style | Specifications Met | Pkg. Qty. | Pkg. | |
Steel | |||||||||||
M10 × 1.5 mm | |||||||||||
| 20 | 12 | 8 | 10 | -0.25 to 0 | Not Rated | Rockwell B76 | Slotted | DIN 427, ISO 2342 | 5 | 000000000 | 00000 |
| 30 | 12 | 18 | 10 | -0.25 to 0 | Not Rated | Rockwell B76 | Slotted | DIN 427, ISO 2342 | 5 | 000000000 | 0000 |
| 35 | 12 | 23 | 10 | -0.25 to 0 | Not Rated | Rockwell B76 | Slotted | DIN 427, ISO 2342 | 5 | 000000000 | 00000 |
| 50 | 12 | 38 | 10 | -0.25 to 0 | Not Rated | Rockwell B76 | Slotted | DIN 427, ISO 2342 | 1 | 000000000 | 0000 |
Threaded Locating and Support Buttons
Use these buttons to support and position workpieces and fixtures from the bottom or side. Their hex shape lets you screw them into a threaded hole with a wrench or socket. Threading makes these buttons easier to replace than press-fit, so they are a good choice for high-wear applications. They’re also known as rest buttons.
Thread | |||||||
|---|---|---|---|---|---|---|---|
| Lg., mm | Wd., mm | Size | Lg., mm | Lg. Tolerance, mm | Specifications Met | Each | |
Steel | |||||||
| 20 | 17 | M10 | 16 | -0.2 to 0.2 | DIN 6320 | 0000000 | 00000 |