McMaster-Carr logo
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    51 Products

    Pull-Out Dowel Pins

    Remove pins even when you only have access to one end or they sit flush with the surface of your part. With one internally threaded end, they are easier to remove than most dowel pins. Thread a screw into the pin and then pull with the removal tool (sold separately). You can also pull the screw with pliers, but there’s more risk of damaging the hole.
    Steel
    Image of Product. Front orientation. Dowel Pins. Pull-Out Removal, Standard Tolerance, Tapped Head.
    Spring Steel—These pins won't deform from stress and vibration. They're stronger than stainless steel but not quite as strong as alloy steel. Pins perform best in dry environments since moisture will cause them to rust.
    Each
    Lg.,
    mm
    Dia. Tolerance,
    mm
    Thread
    Size
    Double Shear Breaking
    Strength, lbf
    Min.
    Hardness
    Specs. Met
    1-49
    50-199
    200-Up
    Spring Steel
     
    6 mm Diameter
    160.004 to 0.012M4 × 0.7 mm6,600Rockwell C52DIN 7979D-m697355A292000000000000000
    180.004 to 0.012M4 × 0.7 mm6,600Rockwell C52DIN 7979D-m697355A296000000000000
    200.004 to 0.012M4 × 0.7 mm6,600Rockwell C52DIN 7979D-m697355A300000000000000
    240.004 to 0.012M4 × 0.7 mm6,600Rockwell C52DIN 7979D-m697355A302000000000000
    280.004 to 0.012M4 × 0.7 mm6,600Rockwell C52DIN 7979D-m697355A303000000000000
    300.004 to 0.012M4 × 0.7 mm6,600Rockwell C52DIN 7979D-m697355A306000000000000
    320.004 to 0.012M4 × 0.7 mm6,600Rockwell C52DIN 7979D-m697355A310000000000000
    360.004 to 0.012M4 × 0.7 mm6,600Rockwell C52DIN 7979D-m697355A314000000000000
    400.004 to 0.012M4 × 0.7 mm6,600Rockwell C52DIN 7979D-m697355A318000000000000
    500.004 to 0.012M4 × 0.7 mm6,600Rockwell C52DIN 7979D-m697355A326000000000000
    600.004 to 0.012M4 × 0.7 mm6,600Rockwell C52DIN 7979D-m697355A334000000000000
     
    Pin Removal Tools
    Each
    Puller Handle92330A300000000
    Tip for 3/16"-5/8" (6-12 mm) Diameter Pin92330A41100000
    Extension (5 1/2" Overall Length)92330A22000000

    Single-End Studs

    Image of Product. Front orientation. Single-End Studs.
    Screw the threaded end of these studs into a tapped hole, and use the unthreaded end as a pivot point, hinge, shaft, or locator pin.
    Steel—These studs are steel for strength and wear resistance. They’re best for dry environments since moisture will cause them to rust. All meet ISO 2342 (formerly DIN 427), an international standard for fastener dimensions.
    Shaft, mm
    Lg.,
    mm
    Thread
    Lg., mm
    Lg.
    Dia.
    Dia.
    Tolerance
    Tensile
    Strength
    Hardness
    Drive
    Style
    Specs. Met
    Pkg.
    Qty.
    Pkg.
    Steel
     
    M4 × 0.7 mm
    84.83.24-0.15 to 0Not RatedRockwell B75Slotted
    		DIN 427, ISO 23421097493A153000000
    104.85.24-0.18 to 0Not RatedRockwell B75Slotted
    		DIN 427, ISO 23422597493A11400000
    124.87.24-0.18 to 0Not RatedRockwell B75Slotted
    		DIN 427, ISO 23422597493A11500000
    164.811.24-0.18 to 0Not RatedRockwell B75Slotted
    		DIN 427, ISO 23422597493A11600000
    184.813.24-0.15 to 0Not RatedRockwell B75Slotted
    		DIN 427, ISO 23421097493A15400000
    204.815.24-0.18 to 0Not RatedRockwell B75Slotted
    		DIN 427, ISO 23422597493A11700000
    254.820.24-0.15 to 0Not RatedRockwell B75Slotted
    		DIN 427, ISO 23421097493A15500000
     

    Vented Pull-Out Dowel Pins

    Insert and remove from blind holes with less effort than pins that aren't vented. The vent relieves trapped air, so pressure doesn't create resistance as you install the pin. Because they have a tapped end, you can thread in a screw and pull the pin out with a removal tool (sold separately). You can also pull using pliers, but there’s more risk of damaging the hole.
    Flat Shaft
    Image of Product. Front orientation. Dowel Pins. Tapped Head, Standard Tolerance, Pull-Out Removal, Vented, Flat Shaft.
    The flat side of these pins creates a vent that's less likely to be blocked than a spiral shaft, but doesn’t offer quite as strong of a hold.
    Spring Steel—These pins won't deform from stress and vibration. They're stronger than stainless steel but not quite as strong as alloy steel. Pins perform best in dry environments since moisture will cause them to rust.
    18-8 Stainless Steel—The choice for wet and outdoor environments. In addition to resisting rust, these pins also withstand mild chemicals such as cleaners and degreasers. They are strong enough to join most components but won't withstand extreme stress and vibration as well as steel.
    Lg.,
    mm
    Dia. Tolerance,
    mm
    Thread
    Size
    Double Shear Breaking
    Strength, lbf
    Min.
    Hardness
    Specs. Met
    Each
    Spring Steel
     
    6 mm Diameter
    160.004 to 0.012M4 × 0.7 mm6,600Rockwell C52DIN 7979D-m698432A20600000
    180.004 to 0.012M4 × 0.7 mm6,600Rockwell C52DIN 7979D-m698432A2100000
    200.004 to 0.012M4 × 0.7 mm6,600Rockwell C52DIN 7979D-m698432A2160000
    240.004 to 0.012M4 × 0.7 mm6,600Rockwell C52DIN 7979D-m698432A2200000
    280.004 to 0.012M4 × 0.7 mm6,600Rockwell C52DIN 7979D-m698432A2240000
    300.004 to 0.012M4 × 0.7 mm6,600Rockwell C52DIN 7979D-m698432A2280000
    360.004 to 0.012M4 × 0.7 mm6,600Rockwell C52DIN 7979D-m698432A2360000
    400.004 to 0.012M4 × 0.7 mm6,600Rockwell C52DIN 7979D-m698432A2400000
    500.004 to 0.012M4 × 0.7 mm6,600Rockwell C52DIN 7979D-m698432A2440000
     
    18-8 Stainless Steel
     
    6 mm Diameter
    160.004 to 0.015M4 × 0.7 mm101,000Rockwell C18DIN 7979C-m698432A11500000
    240.004 to 0.015M4 × 0.7 mm101,000Rockwell C18DIN 7979C-m698432A1170000
    300.004 to 0.015M4 × 0.7 mm101,000Rockwell C18DIN 7979C-m698432A11900000
    360.004 to 0.015M4 × 0.7 mm101,000Rockwell C18DIN 7979C-m698432A12100000
    400.004 to 0.015M4 × 0.7 mm101,000Rockwell C18DIN 7979C-m698432A12200000
     
    Pin Removal Tools
    Each
    Puller Handle92330A300000000
    Tip for 3/16"-5/8" (6-12 mm) Diameter Pin92330A41100000
    Extension (5 1/2" Overall Length)92330A22000000

    Steel Headless Slotted Precision Shoulder Screws

    Image of Product. Front orientation. Shoulder Screws. Steel Headless Slotted Precision Shoulder Screws.
    With no head, you can flush mount these screws in counterbored holes and tight spaces. You can also use them as pins for aligning parts. They are engineered to tight tolerances for assemblies that require smooth and accurate movement, with shoulder diameters twice as precise as those on standard-fit screws. Hand-tighten with a slotted screwdriver to avoid damaging the drive.
    Shoulder
    Lg., mm
    Thread
    Size
    Thread
    Lg., mm
    Tensile
    Strength
    Specs.
    Met
    Pkg.
    Qty.
    Pkg.
    Alloy Steel
     
    5.5 mm Diameter Shoulder (-0.03 mm to 0 mm Tolerance)
    4M4 × 0.7 mm6Not RatedDIN 927594128A10600000
    5M4 × 0.7 mm6Not RatedDIN 927594128A1070000
    6M4 × 0.7 mm6Not RatedDIN 927594128A1080000
    8M4 × 0.7 mm6Not RatedDIN 927594128A1090000
    10M4 × 0.7 mm6Not RatedDIN 927594128A1100000
     

    Fixturing for Parts Inspection

    Image of ProductInUse. Front orientation. Coordinate Measuring Machine Plates and Fixtures. Fixturing for Parts Inspection.
    From towers and brackets to standoffs and supports, these components are the building blocks for your custom fixturing setup. They elevate parts so you can access a variety of angles for measuring and inspecting while protecting your measuring device from hitting the inspection table. You’ll often see them used with coordinate measuring machines (CMMs). They’re not for use in machining applications.
    Standoffs
    Image of Product. Front orientation. Coordinate Measuring Machine Plates and Fixtures. Fixturing for Parts Inspection, Standoffs.
    Standoffs raise the height of towers and angle brackets or extend the reach of supports and clamps. Screw them into one another for added length.
    Dia.,
    mm
    Ht.,
    mm
    Thread
    Lg., mm
    Material
    Each
    M4 × 0.7 mm Threads
     
    Fixed Standoff Height
    12253.8Steel1409N54000000
     
    Trays
    Image of Product. Bottom orientation. Coordinate Measuring Machine Plates and Fixtures. Fixturing for Parts Inspection, Trays.
    Trays have slots to store and organize standoffs, supports, and other small components.
    Lg.,
    mm
    Wd.,
    mm
    Ht.,
    mm
    Material
    Each
    For M4 Thread
    30419625HDPE1409N670000000
     

    Ball-Lock Quick-Change Fixture Clamps

    Image of System. Front orientation. Exploded view. Contains Annotated. Fixture Clamps. Ball-Lock Quick-Change Fixture Clamps.
    Build these components into fixture plates, machine subplates, and tombstones for quick changes. The system clamps and locates at the same time for accurate positioning with repeatability of ±0.0005". Components are compatible with Jergens Ball-Lock, Carr-Lane Carr Lock, and Kurt PinLock quick change systems.
    For accurate positioning, at least two sets of clamps, liners, and receivers are required. Install the receivers in the base plate and the liners in the fixture plate. Then line up the two plates, insert the clamps, and tighten their screws to secure the fixture in place. If more holding capacity is needed, use additional clamps and receivers but omit liners to prevent the clamp from getting stuck in the fixture plate.
    Receiver Plugs
    Image of Product. Front orientation. Fixture Clamps. Ball-Lock Quick-Change Fixture Clamps, Receiver Plugs.
    Push receiver plugs into unused receivers to prevent chips and coolant from accumulating during machining. When installed, plugs sit flush with the surface of the fixture plate. To remove, thread a screw into the tapped hole in the center and pull up.
    For Clamp
    Shank Dia., mm
    Lg.,
    mm
    Thread
    Size
    Material
    Each
    138M4 × 0.7 mmAluminum1349N7200000
    168M4 × 0.7 mmAluminum1349N7300000
    208M4 × 0.7 mmAluminum1349N7400000
    2510M4 × 0.7 mmAluminum1349N7500000

    Threaded Hole Location Gauges

    Image of Product. Back orientation. Threaded Hole Location Gauges.
    Find the true center of threaded holes to precisely align and measure parts. Once you thread these gauges into a hole, their cylinder sticks out as a reliable reference point. They’re often used with a coordinate measuring machine (CMM) to pinpoint the coordinates of the cylinder’s exact center. You can then use those coordinates to measure distances between points or reference them for error-free assembly. Even without a CMM, you can use these gauges with a micrometer to measure accurate center-to-center distances.
    Thread
    Size
    Thread
    Type
    Hardness
    Material
    Each
    M4 × 0.7 mmMetric
    		Rockwell C60Tool Steel
    		6648N160000000

    Fixture Plates

    Lay the foundation for your fixturing setup. These plates have a grid with evenly spaced threaded holes to install angle brackets and other fixturing components. They’re often used to help secure workpieces for measuring and inspecting. Just like a battleship gameboard, the edges are labeled with letters and numbers, making it easy to identify holes. While these lightweight plates aren’t for machining, you can use them for light fabrication jobs, such as laser marking. All can be attached to your table with clamps (not included), making them easy to remove and swap.
    Fixture Plates
    Image of Product. Front orientation. Coordinate Measuring Machine Plates and Fixtures. Fixture Plates.
    Acrylic Plastic—Acrylic plastic plates are clear, so they let light pass through them. This gives you or your vison system unobstructed views of your workpiece from all angles.
    Holes
    Lg.,
    mm
    Wd.,
    mm
    Thk.,
    mm
    Parallel
    Tolerance
    No.
    of
    Ctr.-to-Ctr.,
    mm
    Material
    Each
    M4 Hole Thread Size
    30030019Not Rated32415Acrylic Plastic6364N120000000
     

    Clamps for Parts Inspection

    Image of ProductInUse. Front orientation. Coordinate Measuring Machine Plates and Fixtures. Clamps for Parts Inspection.
    With a light yet sturdy hold, these clamps help you keep workpieces in place hands-free for measuring and inspecting. Thread them right into your fixturing surface, whether it’s a plate, tower, or table. Because they apply less pressure than machining clamps, they won’t distort your parts, so you can take accurate measurements. While these clamps aren’t sturdy enough for use in machining, you can still use them for light fabrication work, such as laser engraving.
    Hold-Down Clamps
    Image of Product. Front orientation. Coordinate Measuring Machine Plates and Fixtures. Clamps for Parts Inspection, Tension Spring.

    Tension Spring

    Hold-down clamps secure parts from the top.
    Tension Spring—Tension spring clamps are the most common type of clamp. Slide the arm down the shaft until it touches the top of your workpiece. Since you apply pressure directly, using too much force might move your part.
    Reach Lg.,
    mm
    Ht.,
    mm
    Thread
    Lg., mm
    Material
    Each
    Tension Spring
     
    M4 × 0.7 mm Threads
    21504.5Aluminum1337N37000000
    38504.5Aluminum1337N3500000
    58504.5Aluminum1337N3600000
     
    back to top