For Holding For Holding |
|---|
Locking Mechanism Locking Mechanism |
|---|
|
For Use With For Use With |
|---|
|
For Manufacturer Model Number For ManufacturerModel Number |
|---|
|
|
For Arbor Hole For Arbor Hole |
|---|
|
Maximum Speed Maximum Speed |
|---|
|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement)  |
|---|
About Sanding Abrasives
More
Dremel Wheel Arbors
Attach cutoff wheels to a Dremel grinder. Arbors are also known as mandrels.
For Max. Wheel | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| For Arbor Hole Size | Thick. | Arbor Hole Dia. | Shank Dia. | Head Dia. | Overall Lg. | Locking Mechanism | Max. Speed, rpm | For Manufacturer Model Number | Each | |
Steel | ||||||||||
| 1-64 | 0.045" | 0.075" | 1/8" | 3/16" | 1 3/8" | Slotted-Head Screw | 35,000 | 100-N/7, 285, 3000-1/24, 3965-02, 4000-2/30, 7800-02, 8000, 8100-N/21, 8200 | 0000000 | 00000 |
| 1/8" | 0.045" | 1/8" | 1/8" | 7/16" | 1 1/2" | Pull-Twist-Release | 35,000 | 100-N/7, 285, 3000-1/24, 3965-02, 4000-2/30, 7800-02, 8000, 8100-N/21, 8200, 8220-1/28 | 0000000 | 0000 |
Wheel Arbors
Attach cutoff wheels, grinding wheels, and other abrasive wheels to hand-held drills and die grinders. Arbors are also known as mandrels.
For technical drawings and 3-D models, click on a part number.
Shank | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| For Arbor Hole Size | For Max. Wheel Thick. | Dia. | Lg. | Head Dia. | Overall Lg. | Material | Locking Mechanism | Max. Speed, rpm | Each | ||
| A | 1/16" | 1/4" | 1/8" | 1 5/8" | 0.197" | 1 3/4" | Steel | Slotted-Head Screw | 20,000 | 0000000 | 00000 |
Arbors for Rubber-Cushioned Abrasive Grinding Bits
Thread rubber-cushioned grinding bits onto one of these arbors and switch between bits without removing the arbor from your tool. Arbors are also known as mandrels.
For technical drawings and 3-D models, click on a part number.
Arbors for Sanding Pads for Internal and Irregular Surfaces
Also known as cross- and square-sanding pad shank adapters, these arbors are required to attach sanding pads for internal and irregular surfaces to hand-held drills and die grinders. Arbors are also known as mandrels.
For technical drawings and 3-D models, click on a part number.
Shank | |||||
|---|---|---|---|---|---|
| For Arbor Hole Size | Dia. | Lg. | Overall Lg. | Each | |
| 3-48 | 1/8" | 1" | 2 1/2" | 00000000 | 00000 |
Spiral-Wound Sanding Roll Arbors
Arbors for Threaded-Stud Flap Sanding Wheels
Use flap sanding wheels with a threaded stud in tools that accept a shank. Arbors are also known as mandrels.
For technical drawings and 3-D models, click on a part number.
| Shank Dia. | Overall Lg. | For Thread Size | Gender | Head Dia. | Each | |
| 1/8" | 1 3/8" | 1/4"-20 | Female | 1/4" | 0000000 | 00000 |
Sanding Sleeve Drums for Hand-Held Power Tools
Slide a sanding sleeve on the drum and tighten the nut or screw to securely hold the sleeve. Secure the shank into the collet or chuck of your tool. A drum is required to use a sanding sleeve.
For technical drawings and 3-D models, click on a part number.
Quick-Change Sanding Sleeve Drums for Hand-Held Power Tools
No tools required—twist the drum head by hand to tighten the sanding sleeve to the drum. Secure the shank into the collet or chuck of your tool. A drum is required to use a sanding sleeve.
For technical drawings and 3-D models, click on a part number.
Drum | ||||||
|---|---|---|---|---|---|---|
| Dia. | Lg. | Shank Dia. | Drum Material | Max. Speed, rpm | Each | |
| 1/2" | 1/2" | 1/8" | Rubber | 30,000 | 00000000 | 00000 |
Sanding Sleeve Drums for Dremel Hand-Held Power Tools
This drum is required to use a sanding sleeve with a Dremel grinder. Slide a sleeve on the drum and tighten the screw to expand the drum to securely hold the sleeve. Install the shank into the grinder’s collet.
Drum | ||||||||
|---|---|---|---|---|---|---|---|---|
| Dia. | Lg. | Shank Dia. | Drum Material | Max. Speed, rpm | Includes | For Manufacturer Model Number | Each | |
Dremel | ||||||||
| 1/2" | 1/2" | 1/8" | Rubber | 5,000 | One 60 Grit Sanding Sleeve | 100-N/7, 285, 3000-1/24, 3965-02, 4000-2/30, 7800-02, 8000, 8100-N/21, 8200 | 0000000 | 00000 |
Buffing Wheel Spindles for Hand-Held Power Tools
The shank on these spindles installs directly into grinder collets and drill chucks. Twist a buffing wheel directly onto the spindle—centrifugal force holds the wheel in place as it turns.
For technical drawings and 3-D models, click on a part number.
| Shank Dia. | Taper Lg. | Overall Lg. | For Max. Arbor Hole Size | Each | |
| 1/8" | 3/8" | 1 3/4" | 1/16" | 0000000 | 00000 |