Convert your straight grinder into an angle grinder.

This 360° shield closes automatically.

Screw these hangers onto your workbench.

The abrasive grains in these bits are blended with rubber, which cushions during grinding to produce a smoother surface texture than other bits with similar grits.

Bits thread onto mounted shanks so you can quickly switch head shapes without removing the shank. The abrasive grains are blended with rubber, which cushions during grinding to produce a smoother surface texture than other bits with similar grits.

Set contains an assortment of tools for grinding, sanding, and cutting on small surface areas.

Set contains a selection of our most popular hex-shank grinding bits. Use them in any drill chuck that accepts a 1/4" hex shank.

Similar to diamond, boron nitride is harder than aluminum oxide and lasts longer. Bits are also known as jig grinding pins and mandrels.

Bits stay cool during grinding so they won’t mar or discolor stainless steel.

Almost as hard as diamond, these tungsten carbide bits cut through nonmetals without generating heat.

Attach cutoff wheels, grinding wheels, and other abrasive wheels to hand-held drills and die grinders.

The extra-coarse threads on these arbors provide a stronger hold on the sanding roll.

Also known as cross- and square-sanding pad shank adapters, these arbors are required to attach sanding pads for internal and irregular surfaces to hand-held drills and die grinders.

No tools required—twist the drum head by hand to tighten the sanding sleeve to the drum.

Slide a flap sanding sleeve on the drum and twist the drum by hand to secure the sleeve.

The shank on these spindles installs directly into grinder collets and drill chucks.

Shape, debur, and sand edges and internal surfaces.

The abrasive-embedded mesh construction gives you more control over sanding pressure, creating finer and more consistent finishes.

A coating prevents dust and debris from building up on the abrasive surface. These sleeves shape, deburr, and sand edges and internal surfaces.

Assortments include a variety of sanding drums and sleeves to shape, deburr, and sand edges and internal surfaces.

The abrasive-embedded mesh construction gives you more control over sanding pressure, creating finer and more consistent finishes.

Choose a bit with the same angle as your countersink to debur the inside of the hole.

As the outer layer wears away, new abrasive is exposed.

Sand inside pipes and tubes as well as on an angle to reach into corners and slots.

Various sizes and grits of flap sanding wheels are included in these assortments. Secure the shank into the collet or chuck of your tool.

The silicon carbide abrasive cuts quickly with light pressure.

Polish small areas and hard-to-reach spots. Use in a drill or grinder for bits and burs.

The edge of the wheel is tapered for polishing joints, grooves, and crevices.

Long, soft cotton strings conform to irregular surfaces and hold on to burring compounds longer than other wheels.

Layers of cloth are sewn together, making these wheels more rigid than those for curved surfaces.

Holes in the hub allow air to flow through so the wheel stays cool and compound lasts longer. Also known as airway buffs.

Use these rigid wheels to remove gouges and scratches from metal workpieces.

Softer than flat-surface wheels, these conform to curves and contours.

The layers of flannel are sewn together, making these wheels more rigid than those for curved surfaces. Also known as Canton flannel buffs.

Made of loose layers of cotton.

Washable and reusable, these pads are good for buffing and polishing painted and clear-coat finishes.

A special fastener on the back of these flexible discs allows you to easily swap one disc for another. Use with a backup pad on grinders for bits and burs.

These bonnets won’t leave swirl marks or scratches when polishing waxed surfaces.

A ceramic alumina abrasive cuts through stainless steel.

Use these wheels for cutting soft metal, plastic, stone, and wood.

Cut plastic, wood, and soft metal such as aluminum, brass, and copper.

A tungsten carbide grit edge cuts through abrasive materials such as composites and fiberglass.

The abrasive lasts longer than that of standard brushes.

Removable bands around the bristles keep them from flaring and breaking. Adjust the bands to change bristle length.

Removable bands around the bristles keep them from flaring and breaking. Adjust the bands to change bristle length.

The bristles are coated with a synthetic compound that keeps them stiff and straight so they last longer than standard brushes.

Use on delicate surfaces.

Abrasive grains are embedded in the entire length of the bristles so the sides act like flexible files. These brushes remove workpiece material as well as surface contamination in a single step.

These brushes conform to corners, curves, and irregular surfaces to remove light-to-medium rust and stains and small burs.

Use on delicate surfaces.

Use on delicate surfaces.

Use on delicate surfaces.

Use on contours and angles or for reaching into cracks and corners.

A special fastener on the back of these brushes allows you to easily swap one brush for another.

Attach the shank to a handle or power tool.

Remove light-to-medium rust and stains and small burs from tubes, pipes, and holes.

Attach the shank to a handle or power tool.

Attach the shank to a handle or power tool.

Bristles at the top of these brushes clean the bottom of closed-end holes.

Use for tasks such as removing weld slag, heavy surface contamination, and large burs.

Restore power to batteries for Dremel tools.