We will reply to your message within an hour.
More
These jobbers'-length bits have the rigidity and length required for most applications.
Also known as screw-machine and stub-length bits, these provide maximum rigidity for drilling straighter holes than jobbers'- and maintenance-length drill bits.
The short flutes provide increased rigidity for drilling straighter holes than standard extended-length drill bits.
Also known as mechanics' bits, these are shorter and more rigid than jobbers’ bits but longer than short‐length bits.
Specially-designed flutes keep these bits centered as they drill, resulting in straighter, rounder holes with tighter tolerances. Also known as double-margin drill bits.
The short flutes on these jobbers'-length bits provide increased rigidity for drilling straighter holes.
Also known as screw-machine and stub-length bits, these provide maximum rigidity for drilling straighter holes than jobbers'-length drill bits.
The parabolic spiral flutes lift chips out of the hole, reducing clogging and improving coolant flow.
Three cutting edges instead of the typical two enable these bits to drill holes with a smoother finish than other bits.
Holes in these bits allow coolant to be run through the tool for more efficient chip evacuation. Use them in CNC machines with coolant-through technology.
Drill safely in flammable environments. Made of Factory Mutual (FM) approved beryllium copper, these bits won’t create sparks that could ignite if they made contact with combustible vapors or residues.
Insert these bits directly into power screwdrivers, impact drivers, and other tools that accept 1/4" hex shanks.
All have a 1/4"-28 threaded shank which installs directly into the threaded spindle on a compatible drill.
In addition to resisting heat and wear better than high-speed steel drill bits, these can also run up to 25% faster and have a longer tool life. Insert them into power screwdrivers, impact drivers, and other tools that accept hex shanks.
These bits have a round or hex shank that fits into the three-jaw chuck on a hammer drill.
A more controlled chip removal reduces heat buildup. Use these bits on brittle material such as block and brick.
The 1/4" hex shank allows these bits to be used with standard impact drivers.
Bore clean, flat bottom holes in soft wood, veneer, and laminates.
Three sharp points allow these bits to drill accurate straight and overlapping holes, even across the grain. Also known as brad-point bits.
Also known as spade bits, these have a centering point and two cutting edges for boring holes in hard and soft wood.
These bits are cut to match a wood screw’s thread and diameter, resulting in a perfect fit for a screw. They produce clean edges when cutting soft and hard wood.
Harder, stronger, and more wear resistant than carbide-tipped steel, solid-carbide bits maintain their sharp edges longer. They require rigid toolholding to prevent breakage and should not be used in hand-held drilling applications.
Carbide-tipped bits maintain their sharp edges when drilling hard material. They are for use in both hand-held drilling and machine-tool applications.
The sharp point allows for gradual penetration to reduce friction and eliminate cracking and chipping when drilling in plastic.
Cobalt steel bits are heat resistant and maintain their sharp edges when drilling hard material. They are for use in both hand-held drilling and machine-tool applications.
Harder, stronger, and more wear resistant than cobalt steel, solid-carbide bits maintain their sharp edges longer. They require rigid toolholding to prevent breakage and should not be used in hand-held drilling applications.
When one end becomes worn, reverse the bit to use the other end.
These bits have short flutes and a sturdy construction which prevent snagging that deforms sheet metal and thin-wall tubing.
Harder, stronger, and more wear resistant than high-speed steel, solid-carbide bits maintain their sharp edges longer. They require rigid toolholding to prevent breakage and should not be used in hand-held drilling applications.
Because softer metal, like aluminum, brass, and bronze, can clog a bit, the flutes on these bits lift chips out of the hole. Also known as slow-spiral drill bits.
Multiple cutting edges on the tip allow these bits to drill quickly through natural stone, granite, and other hard, abrasive material.
Use for drilling in most metal.
With better heat and wear resistance than high-speed steel, cobalt steel bits can run up to 25% faster and have a longer tool life.
Place a washer with an ID of the desired hole size over the bit and it acts as a stop to prevent the bit from drilling a larger hole.
The shaft is made of spring steel instead of hardened steel, so it flexes while drilling, allowing you to drill inside walls or between floors.
Three drill points allow these bits to separate spot-welded panels without damaging the bottom panel.
Insert directly into power screwdrivers, impact drivers, and other tools that accept a 1/4" hex shank.
The built-in guide has a beveled tip that fits into countersunk holes in hardware, such as hinges and latches, to center the bit.
Drill holes using simultaneous rotary and hammering action to break masonry material into tiny granules.
Attach to the shank of a drill bit to extend its reach.
Adjust these extensions to the desired length. They have a quick-change mechanism for fast bit changes.
Tighten the set screws to secure the drill bit in the extension.
A quick-change mechanism allows fast bit changes.
These countersinks come attached to a high-speed steel jobbers’ bit.
These counterbores are attached to a drill bit for drilling and counterboring in a single step.
Secure a hole saw to a drill or drill press with one of these arbors and use the built-in pilot drill to guide the hole saw.