13.5 mm Drill Bits | McMaster-Carr

Black Oxide—The dark finish increases wear resistance and reduces friction to improve chip flow, so these bits can last 50% longer than uncoated bits.

					Shank
	Drill Bit Size, mm	Decimal Size Equiv.	Overall Lg., mm	Max. Drilling Dp., mm	Type	Size	Drill Bit Point Type		Each
Jobbers' Length







				Black Oxide

				13.5	0.5315"	160	81	Round	13.5 mm	Standard	00000000	000000

Reduced-Shank High-Speed Steel Drill Bits

Jobbers' Length

Split

Cut large holes with drill presses and portable drills that have a standard-size chuck. The shank on these bits has a smaller diameter than the cutting tip. High-speed steel is good for general purpose drilling in most metals. Also known as Silver and Deming bits.

Jobbers' Length—These bits have the balance of rigidity and length needed for most applications.

Gold Oxide—Like black oxide, this finish adds wear resistance and reduces friction for improved chip flow. Because it’s less prone to flaking off, it offers better rust protection when bits aren't in use.

					Shank
	Drill Bit Size, mm	Decimal Size Equiv.	Overall Lg., mm	Max. Drilling Dp., mm	Type	Size	Drill Bit Point Type		Each
Jobbers' Length







				Gold Oxide

				13.5	0.5315"	152	63.5	Reduced Round/3-Flat	1/2"	Split	0000000	000000

Drill Bit Guides

Place these guides on your workpiece to drill precise holes without building a fixture. They'll even work on corners and round surfaces. Lines marked on the side allow you to align your holes accurately. Made of hardened steel, they’re tough enough to withstand frequent use.

For Drill Bit Size, mm	For Drill Bit Size Decimal Equiv.	Lg.	Wd.	Ht.	Material		Each
10, 10.5, 11, 11.5, 12, 12.5, 13, 13.5, 14	0.3937", 0.4134", 0.4331", 0.4528", 0.4724", 0.4921", 0.5118", 0.5315", 0.5512"	5 1/4"	1"	1 5/8"	Steel	0000000	000000

Carbide-Tipped Drill Bits

Short Length

Round Shank

Standard

Performance similar to solid carbide but at a lower price point. Like carbide bits, these are stronger than cobalt and high-speed steel and maintain their sharp edges when drilling abrasive material. However, when drilling tough metals like iron and hardened steel, upgrade to carbide for longer life.

Short Length—The most rigid bits for drilling the straightest holes.

					Shank
	Drill Bit Size, mm	Decimal Size Equiv.	Overall Lg., mm	Max. Drilling Dp., mm	Type	Size	Drill Bit Point Type		Each
Short Length







				Uncoated

				13.5	0.5315"	98	40.5	Round	13.5 mm	Standard	000000000	000000

Reduced-Shank Cobalt Steel Drill Bits


Jobbers' Length	Split

More wear resistant than high-speed steel, these bits cut large holes with tools that have a standard-size chuck. The shank has a smaller diameter than the cutting tip and fits drill presses and portable drills. Cobalt steel bits last at least twice as long as high-speed steel. They can also run up to 25% faster at higher temperatures without being damaged on hard materials such as nickel. Also known as Silver and Deming bits.

Jobbers' Length—These bits have the balance of rigidity and length needed for most applications.

Uncoated—Polished to eject chips, these are also known as bright finish bits.

					Shank
	Drill Bit Size, mm	Decimal Size Equiv.	Overall Lg., mm	Max. Drilling Dp., mm	Type	Size	Drill Bit Point Type		Each
Jobbers' Length







				Uncoated

				13.5	0.5315"	152	58	Reduced Round	1/2"	Split	00000000	000000

Chip-Clearing High-Speed Steel Drill Bits


Jobbers' Length Parabolic Flute Round Shank	Split

With flutes that lift chips out of the hole, you don't have to stop drilling to clear these bits manually. They improve coolant flow to dissipate heat and prevent clogs that can damage the bit and ruin the hole. High-speed steel is good for general purpose drilling in most metals.

Parabolic Flute—A U-shaped groove on the flutes cuts faster and clears chips more quickly than high-helix bits, so these are better for drilling deeper holes.

Jobbers' Length—These bits have the balance of rigidity and length needed for most applications.

Uncoated—The most economical option, uncoated bits perform best when used on low-carbon steel and aluminum. Polished to reduce friction, they're also known as bright finish bits.

						Shank
	Drill Bit Size, mm	Decimal Size Equiv.	Overall Lg., mm	Max. Drilling Dp., mm	Flute Type	Type	Size, mm	Drill Bit Point Type		Each
Jobbers' Length







				Uncoated

				13.5	0.5315"	160	108	Parabolic	Round	13.5	Split	0000000	000000

Carbide-Tipped Drill Bits for Hardened Steel

Jobbers' Length

Round Shank

Straight flutes withstand the heavy pressure needed to penetrate hardened steel. These bits cut more aggressively and resist stress better than spiral-flute bits. A lower-priced alternative to solid carbide, they stay sharp when drilling abrasive material but won’t last as long.

Jobbers' Length—These bits have the balance of rigidity and length needed for most applications.

					Shank
	Drill Bit Size, mm	Decimal Size Equiv.	Overall Lg., mm	Max. Drilling Dp., mm	Type	Size	Drill Bit Point Type		Each
Jobbers' Length







				Uncoated

				13.5	0.5315"	152	54	Round	13.5 mm	Notched	0000000	000000

High-Speed Steel Drill Bits for Plastic

The precision-ground, 60° point penetrates gradually to prevent cracking and chipping. It also reduces heat that can deform the material. Use these bits for drilling into acrylic, laminate, and other plastics. They're made of wear-resistant high-speed steel.

Jobbers' Length About Jobbers' Length

					Shank
	Drill Bit Size, mm	Decimal Size Equiv.	Overall Lg., mm	Max. Drilling Dp., mm	Type	Size, mm	Point Angle	Drill Bit Point Type		Each
Uncoated



		13.5	0.5315"	160	108	Round	13.5	60°	Standard	000000000	000000