Also known as screw-machine and stub-length bits, these provide maximum rigidity for drilling straighter holes than jobbers'- and maintenance-length drill bits.

The short flutes provide increased rigidity for drilling straighter holes than standard extended-length drill bits.

These jobbers'-length bits have the rigidity and length required for most applications.

Specially-designed flutes keep these bits centered as they drill, resulting in straighter, rounder holes with tighter tolerances. Also known as double-margin drill bits.

The short flutes on these jobbers'-length bits provide increased rigidity for drilling straighter holes.

These jobbers'-length bits have the rigidity and length required for most applications.

Three cutting edges instead of the typical two enable these bits to drill holes with a smoother finish than other bits.

Specially-designed flutes keep these bits centered as they drill, resulting in straighter, rounder holes with tighter tolerances. Also known as double-margin drill bits.

The short flutes provide increased rigidity for drilling straighter holes than standard extended-length drill bits.

Also known as screw-machine and stub-length bits, these provide maximum rigidity for drilling straighter holes than jobbers'-length drill bits.

With better heat and wear resistance than high-speed steel, cobalt steel bits can run up to 25% faster and have a longer tool life.

In addition to resisting heat and wear better than high-speed steel drill bits, these can also run up to 25% faster and have a longer tool life. Insert them into power screwdrivers, impact drivers, and other tools that accept hex shanks.

These bits have a round or hex shank that fits into the three-jaw chuck on a hammer drill.

Drill holes up to 1 1/2" in diameter.

The SDS-Plus shank has two deep slots and two shallow slots for use with SDS-Plus-drive rotary hammers set to rotary-only mode.

A built-in stop ensures repeatable drilling depths for installing drop-in anchors.

Three sharp points allow these bits to drill accurate straight and overlapping holes, even across the grain. Also known as brad-point bits.

An open spiral-flute design clears chips quickly, so these bits can bore smooth, deep holes through construction lumber, railroad ties, and utility poles. Also known as pole or ship auger bits.

Carbide-tipped bits maintain their sharp edges when drilling hard material. They are for use in both hand-held drilling and machine-tool applications.

These jobbers'-length bits have the rigidity and length required for most applications.

The spear-shaped point drills smoothly through glass and ceramic.

Harder, stronger, and more wear resistant than cobalt steel, solid-carbide bits maintain their sharp edges longer. They require rigid toolholding to prevent breakage and should not be used in hand-held drilling applications.

Harder, stronger, and more wear resistant than high-speed steel, solid-carbide bits maintain their sharp edges longer. They require rigid toolholding to prevent breakage and should not be used in hand-held drilling applications.

These bits have razor-sharp cutting edges for making clean holes in fibrous material.

With better heat and wear resistance than high-speed steel, cobalt steel bits can run up to 25% faster and have a longer tool life.

With better heat and wear resistance than high-speed steel, cobalt steel bits can run up to 25% faster and have a longer tool life.

Unlike traditional wire-installing drill bits, you do not need to strip the end of the wire when using one of these bits. After drilling, insert the wire into the bit's hollow shaft and pull through the hole.

Cobalt steel bits are heat resistant and maintain their sharp edges when drilling hard material. They are for use in both hand-held drilling and machine-tool applications.

Strong and durable, these multipurpose bits are for use with bit screwdrivers.

An opening at the tip accommodates the pin in the recess of tamper-resistant hex screws. These are also known as pin-in-hex or pin-in-socket bits.

Because they make contact on the flat sides of fasteners rather than only on the corners, these magnetic bits significantly reduce slipping and stripping. They’re also known as lobular bits.

Turn hex nuts and cap screws.

The knurled shank on these bits allows finger tightening. They can also be used with the included screwdriver.

When you don't have exact alignment between the fastener and the tool, the ball end allows angled entry to turn screws in hard-to-reach areas.

These bits are also known as nut setters.