System of Measurement System of Measurement |
|---|
|
Size Size | Show |
|---|
|
Size Size | Hide |
|---|
Decimal Size Equivalent Decimal Size Equivalent |
|---|
|
Shank Type Shank Type |
|---|
 |  |
| Reduced Round | Morse Taper |
For Use On For Use On |
|---|
|
|
Length Class Length Class |
|---|
 |
| Reduced Shank Length |
Material Material |
|---|
|
Finish Finish |
|---|
|
Flute Direction Flute Direction |
|---|
 |
| Right Hand |
Shank Size Shank Size |
|---|
|
Point Angle Point Angle |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
|---|
Individual/Set Individual/Set |
|---|
|
Bit Style Bit Style |
|---|
 | Spiral Flute |
Morse Taper Number Morse Taper Number |
|---|
|
Morse Taper Diameter Morse Taper Diameter |
|---|
|
About Drill Bits
More
Drill Bit Decimal Size Equivalents
More
1/2" Diameter Reduced-Shank Drill Bits
The shank has a smaller diameter than the tip, allowing you to drill large holes with machines that have small-capacity chucks. Also known as Silver and Deming bits, they have a 1/2” diameter shank.
Drill bits with flats on shank have three flat sides to prevent the bit from slipping in the drill chuck.
For technical drawings and 3-D models, click on a part number.
Shank | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Size | Decimal Size Equivalent | Overall Lg. | Max. Drilling Dp. | Type | Size | For Use On | Point Style | Each | |
Drill Bits | |||||||||
Inch | |||||||||
Black-Oxide High-Speed Steel | |||||||||
| 31/32" | 0.9688" | 6" | 2.1" | Reduced Round | 1/2" | Steel, Iron, Stainless Steel | Standard | 0000000 | 000000 |
Drill Bits with Flats on Shank | |||||||||
Inch | |||||||||
Black-Oxide High-Speed Steel | |||||||||
| 31/32" | 0.9688" | 6" | 2.1" | Reduced Round | 1/2" | Steel, Iron, Stainless Steel | Standard | 00000000 | 00000 |
Cobalt Steel 1/2" Diameter Reduced-Shank Drill Bits
With better heat and wear resistance than high-speed steel, these cobalt steel bits can run up to 25% faster and have a longer tool life. The shank has a smaller diameter than the tip, allowing you to drill large holes with machines that have small-capacity chucks. A split point keeps the bit centered without a pilot hole. Also known as Silver and Deming bits, they have a 1/2” diameter shank.
Titanium-nitride (TiN) coated drill bits last longer and can drill at higher speeds than uncoated drill bits.
Shank | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Size | Decimal Size Equivalent | Overall Lg. | Max. Drilling Dp. | Type | Size | Point Style | For Use On | Each | |
Inch | |||||||||
Uncoated Cobalt Steel | |||||||||
| 31/32" | 0.9688" | 6" | 2.1" | Reduced Round | 1/2" | Split | Steel, Hardened Steel, Tool Steel, Iron, Stainless Steel, Nickel | 0000000 | 0000000 |
Titanium-Nitride (TiN) Coated Cobalt Steel | |||||||||
| 31/32" | 0.9688" | 6" | 3.13" | Reduced Round | 1/2" | Split | Steel, Hardened Steel, Tool Steel, Iron, Stainless Steel, Nickel, Titanium, Fiberglass | 0000000 | 000000 |
High-Speed Steel Morse Taper-Shank Drill Bits
Install the Morse taper shank directly into the tapered spindle on machines such as drill presses and lathes.
For technical drawings and 3-D models, click on a part number.
Morse Taper | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Size | Decimal Size Equivalent | No. | Dia. | Overall Lg. | Max. Drilling Dp. | Shank Type | Point Style | For Use On | Each | |
Inch | ||||||||||
Black-Oxide High-Speed Steel | ||||||||||
| 31/32" | 0.9688" | 3 | 0.938" | 11" | 4.92" | Morse Taper | Standard | Steel, Iron, Stainless Steel | 00000000 | 000000 |