Drill Presses | McMaster-Carr

	Mounting Location Mounting Location

Bench Top

Floor

	Voltage Voltage

120V AC

240V AC

440V AC

	Motor Power Motor Power

	Number of Speeds Number of Speeds

Variable

	For Maximum Bit Shank Size For Maximum Bit Shank Size

	Maximum Workpiece Diameter Maximum Workpiece Diameter

	Motor Phase Motor Phase

Single

Three

	For Maximum Drill Bit Size for Steel For Maximum Drill Bit Size for Steel

	For Bit Shank Type For Bit Shank Type


Hex	Round

Threaded

	Spindle Shank Type Spindle Shank Type

Morse

Jacobs

Chuck

	Spindle Travel Spindle Travel

	Chuck Type Chuck Type

Keyed

Keyless

	Base Length Base Length

	Overall Height Overall Height

	Maximum No-Load Speed Maximum No-Load Speed

	Weight Weight

	Table Length Table Length

	Plug Type Plug Type

Two Prong

Three Prong

	Table Width Table Width

	Motor Current Motor Current

	Chuck Key Included Chuck Key Included

Yes

	RoHS (Restriction of Hazardous Substances) RoHS (Restriction of Hazardous Substances)

RoHS Compliant

	REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration, Evaluation, Authorization and Restriction of Chemicals)

REACH Compliant

Forward

How can we improve?

88 Products

Drill Bit Decimal Size Equivalents

About Drill Bits

10" Max. Workpiece Dia.

13 1/4" Max. Workpiece Dia.

15" Max. Workpiece Dia.

Drill presses that cannot be sold to Canada are restricted by local energy efficiency regulations.

Economy Benchtop Drill Presses																Replacement Spring Cap Assembly
Max. Workpiece Dia.	Max. Table Cap., lbs.	For Max. Drill Bit Size for Cast Iron	For Max. Bit Shank Size	Max. No-Load Speed, rpm	Chuck Key Included	No. of Speeds	Spindle Jacobs Taper No.	Spindle Morse Taper No.	Spindle Travel	Motor Power, hp	Motor Current, A	Wt., lbs.	Cannot Be Sold To		Each		Each
120V AC—Single Phase
Jacobs Spindle Shank
10"	70	1/2"	1/2"	3,070	Yes	5	33	__	2 1/2"	1/3	4.1	70	__	00000000	0000000	00000000	000000
13 1/4"	80	1/2"	1/2"	3,350	Yes	16	33	__	3 1/4"	1/3	6	120	Canada	0000000	000000	0000000	00000
120V AC/240V AC—Single Phase
Morse Spindle Shank
15"	100	5/8"	5/8"	3,450	Yes	16	__	2	5"	1/2	7.3	150	__	0000000	00000000	0000000	00000

Replacement Spindle Assembly for Drill Presses with Morse Spindle Shanks

0000000

Each

0000000

Extended-Reach Economy Benchtop Drill Presses

To accommodate large, odd-shaped pieces of material, the head of this drill press moves 12" forward and backward. It also tilts 45° left and 90° right (as viewed when facing the drill press).

			For Max. Drill Bit
Max. Workpiece Dia.	Max. Table Cap., lbs.	For Bit Shank Type	Size for Steel	Size for Cast Iron	For Max. Bit Shank Size	Max. No-Load Speed, rpm	Chuck Key Included	No. of Speeds	Spindle Morse Taper No.	Spindle Travel	Motor Power, hp	Motor Current, A	Wt., lbs.	Current		Each
120V AC—Single Phase
Morse Spindle Shank
33"	70	Hex, Round	3/8"	5/8"	5/8"	3,100	Yes	5	2	3 5/32"	1/2	5	95	4.8A	00000000	0000000

Adjustable-Position Milwaukee Magnetic-Base Drill Presses

Chuck Spindle Shank

Morse Spindle Shank

Lock the magnet to secure the base and then move the motor to center the cutter for pinpoint accuracy. You can move the motor 3/4" forward and backward and tilt it 20° left and right. Switch these drills from forward to reverse without stopping—ideal for both drilling and tapping applications (not recommended for use with pipe taps). In addition, a dial lets you adjust the speed to match your application, making these great for drilling hard materials at slow speeds. Base attaches to flat ferrous surfaces (such as steel and cast iron). Holding force (also called drill point breakaway) is calculated against a 1" thick steel plate. Drills include a spoked feed handle that mounts on either side.

Drill presses for 3/4" and 1 1/4" max. drill bit sizes can be used with carbide-tipped hollow-core cutters.

Drill press for 1/2" max. drill bit size cannot be used with hollow-core cutters. It is not for use with 5/8"-11 and 1/2"-13 taps.

Note: To avoid damaging the electromagnet, do not mount press to a base that has a welder already grounded to it.

									O'all
For Max. Drill Bit Size	For Max. Cutter Dia.	For Max. Bit Shank Size	For Max. Tap Size	Max. No-Load Speed, rpm	Spindle Morse Taper No.	Spindle Travel	Holding Force, lbs.	For Min. Surface Thick.	Lg.	Wd.	Ht.	Wt., lbs.	Manufacturer Model No.	Specifications Met		Each
120V AC
Chuck Spindle Shank
3/4"	2 1/4"	3/4"	1"-14	350	__	11"	1,600	1/2"	17"	7 1/2"	32 1/2"	70	4206-1	UL Listed	0000000	000000000
1/2"	__	1/2"	5/8"-18	600	__	11"	1,600	1/2"	15 1/4"	7 1/2"	29 1/2"	60	4204-1	UL Listed	0000000	00000000
Morse Spindle Shank
1 1/4"	2 1/4"	__	1"-14	750	3	11"	1,600	1/2"	17"	7 1/2"	32 1/2"	70	4209-1	UL Listed	0000000	00000000
1 1/4"	2 1/4"	__	1"-14	500	3	11"	1,600	1/2"	17"	7 1/2"	32 1/2"	70	4208-1	UL Listed	0000000	00000000

Replacement Drill Chuck Key for 3/4" Max. Drill Bit Size	0000000	Each	000000
16 fl. oz. Cutting, Tapping, and Threading Coolant	00000000	Each	00000
Replacement Drill Chuck Key for 1/2" Max. Drill Bit Size	0000000	Each	0000

Fixed-Position Milwaukee Magnetic-Base Drill Presses

Chuck Spindle Shank

Morse Spindle Shank

Switch these drills from forward to reverse without stopping—ideal for both drilling and tapping applications (not recommended for use with pipe taps). In addition, a dial lets you adjust the speed to match your application, making these great for drilling hard materials at slow speeds. Base attaches to flat ferrous surfaces (such as steel and cast iron). Holding force (also called drill point breakaway) is calculated against a 1" thick steel plate. Drills include a spoked feed handle that mounts on either side.

Drill presses for 3/4" and 1 1/4" max. drill bit sizes can be used with carbide-tipped hollow-core cutters.

Drill press for 1/2" max. drill bit size cannot be used with hollow-core cutters. It is not for use with 5/8"-11 and 1/2"-13 taps.

Note: To avoid damaging the electromagnet, do not mount press to a base that has a welder already grounded to it.

									O'all
For Max. Drill Bit Size	For Max. Cutter Dia.	For Max. Bit Shank Size	For Max. Tap Size	Max. No-Load Speed, rpm	Spindle Morse Taper No.	Spindle Travel	Holding Force, lbs.	For Min. Surface Thick.	Lg.	Wd.	Ht.	Wt., lbs.	Manufacturer Model No.	Specifications Met		Each
120V AC
Chuck Spindle Shank
1/2"	__	1/2"	5/8"-18	600	__	9"	1,600	1/2"	14 1/2"	7 1/2"	25 1/2"	50	4202/4253-1	UL Listed	0000000	000000000
3/4"	2 1/4"	3/4"	1"-14	350	__	9"	1,600	1/2"	16 1/4"	7 1/2"	27"	65	4210-1	UL Listed	0000000	00000000
Morse Spindle Shank
1 1/4"	2 1/4"	__	1"-14	750	3	9"	1,600	1/2"	16 1/4"	7 1/2"	27"	65	4202/4292-1	UL Listed	0000000	00000000
1 1/4"	2 1/4"	__	1"-14	500	3	9"	1,600	1/2"	16 1/4"	7 1/2"	27"	65	4202/4297-1	UL Listed	0000000	00000000

Replacement Drill Chuck Key for 1/2" Max. Drill Bit Size	0000000	Each
16 fl. oz. Cutting, Tapping, and Threading Coolant	00000000	Each
Replacement Drill Chuck Key for 3/4" Max. Drill Bit Size	0000000	Each

Small-Hole Precision Benchtop Drill Presses

Use for drilling small holes. A sensitive belt-drive motor reduces drill breakage and damage.

120V AC—Single Phase
Max. Workpiece Dia.	For Max. Drill Bit Size for Steel	For Max. Bit Shank Size	Max. No-Load Speed, rpm	Chuck Manufacturer	No. of Speeds	Spindle Jacobs Taper No.	Spindle Travel	Motor Power, hp	Motor Current, A	Wt., lbs.		Each
Jacobs Spindle Shank
7"	1/8"	1/8"	20,000	Albrecht	Variable	0	1 1/2"	1/5	2	25	0000000	000000000

Multispeed Economy Floor Drill Presses

15" Max. Workpiece Dia.

17" Max. Workpiece Dia.

20" Max. Workpiece Dia.

Select from a number of speeds by repositioning the drive belt before starting the drill press.

Multispeed Economy Floor Drill Presses														Replacement Spring Cap Assembly
Max. Workpiece Dia.	Max. Table Cap., lbs.	For Max. Drill Bit Size for Steel	For Max. Bit Shank Size	Max. No-Load Speed, rpm	Chuck Key Included	No. of Speeds	Spindle Morse Taper No.	Spindle Travel	Motor Power, hp	Current	Wt., lbs.		Each		Each
120V AC/240V AC—Single Phase
Morse Spindle Shank
15"	100	5/8"	5/8"	3,450	Yes	16	2	5"	1/2	7.3A	165	0000000	000000000	0000000	000000
17"	100	5/8"	5/8"	3,450	Yes	16	2	5"	1	10A	180	0000000	00000000	0000000	00000
120V AC—Single Phase
Morse Spindle Shank
20"	65	1"	3/4"	4,200	Yes	12	3	4 3/4"	1	13.5A	315	00000000	00000000	000000	00

Replacement Spindle Assembly for Drill Presses for 17" Max. Workpiece Dia.	0000000	Each	0000000
Replacement Spindle Assembly for Drill Presses for 15" Max. Workpiece Dia.	0000000	Each	000000

Variable-Speed Economy Floor Drill Presses

Turn the dial on this drill press while it is running to get the optimum speed for your job. A laser projects a crosshair at the point of bit contact and a digital readout displays the spindle speed.

120V AC/240V AC—Single Phase
Max. Workpiece Dia.	Max. Table Cap., lbs.	For Max. Drill Bit Size for Steel	For Max. Bit Shank Size	Max. No-Load Speed, rpm	Spindle Morse Taper No.	Spindle Travel	Motor Power, hp	Current	Wt., lbs.		Each
Morse Spindle Shank
18"	88	5/8"	5/8"	3,000	2	6"	1	15A	245	0000000	000000000

Extended-Reach Economy Floor Drill Presses

To accommodate large, odd-shaped pieces of material, the head of this drill press moves 12" forward and backward. It also tilts 45° left and 90° right (as viewed when facing the drill press).

		For Max. Drill Bit
Max. Workpiece Dia.	Max. Table Cap., lbs.	Size for Steel	Size for Cast Iron	For Max. Bit Shank Size	Max. No-Load Speed, rpm	Chuck Key Included	No. of Speeds	Spindle Morse Taper No.	Spindle Travel	Motor Power, hp	Current	Wt., lbs.		Each
120V AC—Single Phase
Morse Spindle Shank
33"	50	3/8"	5/8"	5/8"	3,100	Yes	5	2	3 5/32"	1/2	4.8A	143	00000000	0000000

Floor Drill Presses

18-1/8" Max. Workpiece Dia.

20" Max. Workpiece Dia.

The weight and rigidity of these presses prevent vibration so you can maintain close tolerances for high-quality metal drilling. Turn the dial on these drill presses while they are running to get the optimum speed for your job.

Drill presses with 20" max. workpiece diameter have a safety guard that swings away for easy tool changes.

120V AC—Single Phase
Max. Workpiece Dia.	Max. Table Cap., lbs.	For Max. Drill Bit Size for Steel	For Max. Bit Shank Size	Max. No-Load Speed, rpm	Chuck Key Included	No. of Speeds	Spindle Morse Taper No.	Spindle Travel	Motor Power, hp	Current	Wt., lbs.		Each
Morse Spindle Shank
18 1/8"	200	1 1/16"	3/4"	1,200	Yes	Variable	3	5 3/8"	2	6.8A	675	000000	000000000
120V AC/240V AC—Single Phase
Morse Spindle Shank
20"	300	7/8"	__	2,000	No	Variable	3	6 1/2"	1 1/2	17.9A	590	0000000	00000000
240V AC—Three Phase
Morse Spindle Shank
20"	300	7/8"	__	2,000	No	Variable	3	6 1/2"	1 1/2	17.9A	590	0000000	00000000
440V AC—Three Phase
Morse Spindle Shank
20"	300	7/8"	__	2,000	No	Variable	3	6 1/2"	1 1/2	17.9A	590	0000000	00000000

Optional Morse Taper Arbor with Drill Chuck for 20" Floor Drill Presses

0000000

Each

0000000

Jancy Magnetic-Base Drills for Hollow-Core Cutters

These drills work with hollow-core cutters to cut only on the periphery of the hole and produce a solid slug. This allows for a faster and easier cut than drilling with standard drill bits. Also known as magnetic core drilling machines.

They have a feed handle that mounts on the left or right side of the drill. The electromagnetic base attaches to flat ferrous surfaces (such as steel and cast iron).These drills also have a valve to adjust coolant flow. Holding force (also called drill-point breakaway) is calculated against a 1" thick steel plate.

Chucks and adapters (sold separately) allow these models to accept standard drill bits.

											O'all
	For Max. Cutter Dia.	For Cutter Shank Size	Max. Cutting Dp.	Spindle Travel	Max. No-Load Speed, rpm	No. of Speeds	Current, A	Holding Force, lbs.	For Min. Surface Thick.	Coolant Included	Lg.	Wd.	Ht.	Wt., lbs.	Manufacturer Model No.		Each
120V AC
A	1 3/8"	3/4"	2"	5 11/16"	590	1	9.5	2,810	1/2"	No	10 1/4"	3 1/2"	19 3/4"	25.8	JME Holemaker III	0000000	000000000
B	1 1/2"	3/4"	2"	2 9/16"	480	1	9.4	650	3/8"	No	13 5/8"	7 7/8"	17 5/8"	32	JHM USA101	0000000	00000000
C	2 9/16"	3/4"	2"	5 11/16"	520	2	12.6	3,080	1/2"	No	20 1/4"	9 7/8"	23 5/8"	35.5	JCM 256 U	0000000	00000000

1 gal. Cutting, Tapping, and Threading Coolant for Styles B and C	Each	000000
1.6 fl. oz. Cutting, Tapping, and Threading Coolant for Styles B and C	Each	0000
1/2" Chuck and Adapter for Jancy Magnetic-Base Drills JHM USA101	Each	000000
5/8" Chuck and Adapter for Jancy Magnetic-Base Drills JCM 256 U	Each	000000

Chuck and Adapter for Jancy Magnetic-Base Drills

These chucks and adapters will allow your Jancy magnetic-base drills to accept standard drill bits.

	For Machine Spindle
For Max. Bit Shank Size	Shank Type	Shank Dia.	Chuck Key Included	For Manufacturer Model Number		Each
Jancy
1/2"	Straight	1/2"	Yes	JHM USA101	0000000	0000000
5/8"	Straight	3/4"	Yes	JCM 256 U	0000000	000000

Hougen Magnetic-Base Drills for Hollow-Core Cutters

They have a feed handle that mounts on the left or right side of the drill. The electromagnetic base attaches to flat ferrous surfaces (such as steel and cast iron). Holding force (also called drill-point breakaway) is calculated against a 1" thick steel plate.

											O'all
	For Max. Cutter Dia.	For Cutter Shank Size	Max. Cutting Dp.	Spindle Travel	Max. No-Load Speed, rpm	No. of Speeds	Current, A	Holding Force, lbs.	For Min. Surface Thick.	Coolant Included	Lg.	Wd.	Ht.	Wt., lbs.	Manufacturer Model No.		Each
120V AC
A	1 1/2"	3/4"	2"	2"	450	1	8	995	3/8"	Yes	11 5/8"	7 3/4"	19 5/8"	30	HMD904	0000000	000000000
B	2 3/8"	3/4"	3"	3"	700	3	12.5	1,290	3/8"	Yes	12 3/4"	8 1/4"	26"	49	HMD920	0000000	00000000
240V AC
B	2 3/8"	3/4"	3"	3"	700	3	6.3	1,290	3/8"	Yes	12 3/4"	8 1/4"	26"	49	HMD920	0000000	00000000

1 gal. Cutting, Tapping, and Threading Coolant	0000000	Each	000000
1.6 fl. oz. Cutting, Tapping, and Threading Coolant	0000000	Each	0000

Safety Guards for Drill Presses

Shown on Drill Press (Drill Press and Bit Not Included)

Keep your fingers and hands protected from your drill bit, drill chuck, and flying chips. This guard retracts as the drill penetrates your material, lowers when the spindle is raised, and flips out of the way for quick bit changes. A depth adjustment knob allows for quick adjusting of the guard position. Body is made from high-impact clear plastic for an unobstructed view.

For Max. Bit Shank Size	Ht. Range	Number of Clamps	Includes	Body Material	Body Color	Features		Each
2 1/8"	4 1/2"-6 11/16"	5	Five Clamps for 1 3/4" (45 mm), 2" (52 mm), 2 3/8" (60 mm), 2.6" (66 mm), and 3" (75 mm) Drill Press Spindle Shafts	Plastic	Clear	Depth Adjusting Knob	0000000	0000000

Mini Magnetic Drill Base

Drill Not Included

Get the accuracy of a drill press when you use this lightweight, portable drill base with Milwaukee electric drill models 0234-6 and 0244-1. The powerful electromagnetic base firmly attaches to flat, ferrous surfaces such as steel and cast iron. Holding force (also called drill-point breakaway) is calculated against a 1" thick steel plate.

Base Dia.	Base Ht.	Drill Travel	For Min. Surface Thick.	Holding Force, lbs.	Voltage	Toggle Switch Type	Wt., lbs.		Each
4"	2 3/8"	3.9"	0.2"	770	120V AC	On/Off	12	00000000	0000000

Core Drill Bits for Glass and Ceramic

Reduce the chance of chipping and cracking when drilling in glass and ceramic. These hollow bits are diamond-coated for long life and fast cutting. They are for use in drill presses only and require an adapter (sold separately). Attach the threaded nut to the adapter, then install the adapter into the chuck on a drill press. Coolant, such as water, is required when drilling with these bits. The size listed is the bit's OD.

Drill press adapters attach to a water line, which acts as coolant during drilling, and include an on/off valve. Both adapters work with all of these drill bits, but choose the shank size that fits your application.

For technical drawings and 3-D models, click on a part number.

Drill Press Adapters

Shank			Inlet
Size	Lg.	Body Lg.	Pipe Size	Thread Type	Gender	Features		Each
3/8"	1 1/2"	3 1/2"	1/8	NPT	Male	On/Off Valve	0000000	0000000
1/2"	1 1/2"	3 1/2"	1/8	NPT	Male	On/Off Valve	0000000	000000

Dremel Drill Press Attachments

For Manufacturer Model No.		Each
100-N/7, 285, 3000-1/24, 3965-02, 4000-2/30, 7800-02, 8000, 8100-N/21, 8200	00000000	000000

Morse Taper Arbors with Drill Chuck

This arbor with chuck allows drills with a #3 Morse taper spindle to accept standard drill bits.

For Bit Shank Size		For Machine Spindle Morse Taper			Chuck Key				Arbor
Inch	mm	Number	Dia.	Chuck Material	Number	Material	Length	Included	Lg.	Included		Each
3/16"-3/4"	4.5-19	3	0.938"	Steel	K4	Steel	5 3/32"	Yes	5 1/2"	Yes	0000000	0000000

Morse Taper to Jacobs Taper Drill Chuck Arbors

The Morse taper end fits into a machine spindle and the Jacobs taper end is compatible with a Jacobs taper drill chuck. Morse taper spindles are most often found on drill presses. These arbors are made of hardened, precision-ground steel.

For Machine Spindle Morse Taper		For Drill Chuck Jacobs Taper
Number	Dia.	Number	Dia.	Overall Lg.	Material		Each
1	0.475"	0	0.25"	3 3/16"	Steel	0000000	000000
1	0.475"	1	0.384"	3 25/64"	Steel	0000000	00000
1	0.475"	2	0.559"	3 5/8"	Steel	0000000	00000
1	0.475"	3	0.811"	4 1/64"	Steel	0000000	00000
1	0.475"	6	0.676"	3 25/32"	Steel	0000000	00000
1	0.475"	33	0.624"	3 25/32"	Steel	0000000	00000
2	0.7"	0	0.25"	3 25/32"	Steel	0000000	00000
2	0.7"	1	0.384"	3 63/64"	Steel	0000000	00000
2	0.7"	2	0.559"	4 7/32"	Steel	0000000	00000
2	0.7"	3	0.811"	4 39/64"	Steel	0000000	00000
2	0.7"	4	1.124"	5 3/64"	Steel	0000000	00000
2	0.7"	6	0.676"	4 3/8"	Steel	0000000	00000
2	0.7"	33	0.624"	4 17/64"	Steel	0000000	00000
3	0.938"	1	0.384"	4 47/64"	Steel	0000000	00000
3	0.938"	2	0.559"	4 31/32"	Steel	0000000	00000
3	0.938"	3	0.811"	5 23/64"	Steel	0000000	00000
3	0.938"	4	1.124"	5 51/64"	Steel	0000000	00000
3	0.938"	5	1.413"	5 29/32"	Steel	0000000	00000
3	0.938"	6	0.676"	5 1/8"	Steel	0000000	00000
3	0.938"	33	0.624"	5 1/8"	Steel	0000000	00000
4	1.231"	2	0.559"	6"	Steel	0000000	00000
4	1.231"	3	0.811"	6 3/8"	Steel	0000000	00000
4	1.231"	4	1.124"	6 13/16"	Steel	0000000	00000
4	1.231"	5	1.413"	6 15/16"	Steel	0000000	00000
4	1.231"	6	0.676"	6 5/32"	Steel	0000000	00000
4	1.231"	33	0.624"	6 5/32"	Steel	0000000	00000
5	1.748"	3	0.811"	7 9/16"	Steel	0000000	00000
5	1.748"	4	1.124"	8 1/8"	Steel	0000000	00000
5	1.748"	5	1.413"	8 1/8"	Steel	0000000	000000

Machinable-End Morse Taper Drill Chuck Arbors

One end is made of soft steel that can be machined to suit your job requirements; the Morse taper end fits into a machine spindle. Morse taper spindles are most often found on drill presses.

For Machine Spindle Morse Taper		Machine End
Number	Dia.	Body Dia.	Body Lg.	Overall Lg.	Material		Each
2	0.7"	1 3/4"	2 1/8"	5 1/16"	1144 Carbon Steel	0000000	000000
3	0.938"	1 3/4"	2 1/8"	5 3/16"	1144 Carbon Steel	0000000	00000
4	1.231"	2 1/2"	3"	7 5/8"	1144 Carbon Steel	0000000	00000
5	1.748"	3"	4 1/16"	9 15/16"	1144 Carbon Steel	0000000	000000

Morse Taper to Thread-Mount Drill Chuck Arbors

The Morse taper end fits into a machine spindle and the threaded end is compatible with a threaded drill chuck. Morse taper spindles are most often found on drill presses. These arbors are made of hardened, precision-ground steel.

For technical drawings and 3-D models, click on a part number.

For Machine Spindle Morse Taper
Number	Dia.	For Drill Chuck Mounting Hole Thread Size	Overall Lg.	Material		Each
2	0.7"	3/8"-24	4"	Steel	0000000	000000
2	0.7"	1/2"-20	4 7/64"	Steel	0000000	00000
2	0.7"	5/8"-16	4 3/16"	Steel	0000000	00000

Straight-Shank Drill Chuck Arbors with Drill-Feed Attachment

For better control when drilling small holes with a drill press or milling machine, the attachment on this arbor lets you apply light feed pressure with your fingers while the machine rotates the bit. A spring-loaded, ball-bearing drill feed automatically retracts when the gripping ring is released. The straight shank fits into a machine spindle and the Jacobs taper end is compatible with a Jacobs taper drill chuck.

		For Drill Chuck Jacobs Taper
Shank Dia.	Spindle Travel	Number	Dia.	Overall Lg.	Material		Each
1/2"	3/4"	0	0.25"	2 15/16"	Steel	0000000	0000000

Arbor Adapters for Milwaukee Hollow-Core Cutters

Arbor Adapter with
Morse Taper
Shank

Arbor Adapter with Straight Shank

These arbor adapters are required when using Milwaukee hollow-core cutters, also known as annular cutters. They come with a pilot pin, which aligns the cutter and ejects the slug.

Morse Taper			For Bit Shank
Number	Dia.	Shank Dia.	Thread Size	Thread Pitch	Overall Lg.	For Cutter Material	Material	Manufacturer	Manufacturer Model Number	For Manufacturer Model Number	Includes		Each
With Morse Taper Shank
3	0.938"	__	M18	1.5mm	10"	Carbide-Tipped Steel	Steel	Milwaukee	49-57-0010	4202, 4208-1, 4209-1, 4292-1, 4297-1	Oil Hose, Oiler, Pilot Pin	00000000	0000000
With Straight Shank
__	__	3/4"	M18	1.5mm	10"	Carbide-Tipped Steel	Steel	Milwaukee	49-57-0030	4206-1, 4210-1	Oil Hose, Oiler, Pilot Pin	00000000	000000

Arbor Adapters for Hollow-Core Cutters

Arbor Adapter with
Morse Taper
Shank

Arbor Adapter
with Straight
Shank

Use hollow-core cutters on manual drill presses and milling machines. Also known as annular cutters.

For technical drawings and 3-D models, click on a part number.

Morse Taper
Number	Dia.	Shank Dia.	For Cutter Shank Size	Overall Lg.	For Cutter Material	Material		Each
With Morse Taper Shank
2	0.7"	__	3/4"	6 1/4"	Cobalt Steel, High-Speed Steel	High-Speed Steel	000000000	000000
3	0.938"	__	3/4"	6 1/4"	Cobalt Steel, High-Speed Steel	High-Speed Steel	000000000	000000
With Straight Shank
__	__	3/4"	3/4"	5 1/8"	Cobalt Steel, High-Speed Steel	High-Speed Steel	000000000	000000