The toughest bits available, these withstand the shock and twisting force of impact drivers.

Drive screws with both ends of these bits. Use with hand drivers.

Protect your stainless steel screws by using a stainless steel bit. If steel flakes off a standard bit and into the recess, it can lead to rust and contamination. These bits eliminate that risk.

A wide tip makes good contact in shallow and coated screw recesses, such as those filled with paint.

Thread these bits directly into your driving tool for minimal wobble in assembly applications.

Strong and durable, these multipurpose bits are for use with bit screwdrivers.

When you don't have exact alignment between the fastener and the tool, the ball end allows angled entry to turn screws in hard-to-reach areas.

When you don't have exact alignment between the fastener and the bit, the ball end allows angled entry to turn screws in hard-to-reach areas. A retaining ring grips inside the recess to hold screws in place.

Strong and durable, these multipurpose bits are for use with bit screwdrivers. They're designed for screws with a square recess in the head and are also known as Robertson bits.

An exterior stop collar prevents fasteners from being driven too deep. Use with soft materials such as drywall, wood, and fiberboard.

Protect your stainless steel screws by using a stainless steel bit. If steel flakes off a standard bit and into the recess, it can lead to rust and contamination. These bits eliminate that risk.

Less likely to crack or shatter under high torque than standard bits, these are often used with power tools to install machine screws.

When you don't have exact alignment between the fastener and the tool, the ball end allows angled entry to turn screws in hard-to-reach areas.

The slightly tapered tip wedges into the screw recess for a secure hold. Also known as Torx-Align bits.

Strong and durable, these multipurpose bits are for use with bit screwdrivers. They are often used with power tools to install sheet metal screws.

Protect your stainless steel screws by using a stainless steel bit. If steel flakes off a standard bit and into the recess, it can lead to rust and contamination. These bits eliminate that risk.

The small-diameter shaft can access screws in narrow recessed holes.

An opening at the tip accommodates the pin in the recess of tamper-resistant Torx screws. These are also known as pin-in-Torx bits.

Strong and durable, these multipurpose bits are for use with bit screwdrivers.

An opening at the tip accommodates the pin in the recess of tamper-resistant hex screws. These are also known as pin-in-hex or pin-in-socket bits.

These are also known as TP3® bits.

Use with screws that have two drilled holes.

Also known as Reed and Prince bits.

While screws with a Square/Phillips combination drive can be turned with either a Square or Phillips bit, these make the best contact so you can apply high torque without slipping and stripping the recess. They are also known as Quadrex bits.

These bits have an offset cross shape. They’re also known as ACR® bits.

The tip is shaped like an eight-pointed star.

The six rounded points fit the star-shaped recess of Torx-Plus screws. These bits have a similar profile to Torx but are not recommended for use with standard Torx screws.

Turn the screws found in Apple devices.

Ribs forged into the wings of these offset-cross-shaped bits grip the screw recess to reduce stripping. They are also known as ACR® bits.

These are also known as known as butterfly and Type G bits.

The toughest bits available, these withstand the shock and twisting force of impact drivers. A magnet holds the nut in place.

Turn hex nuts and cap screws.

Less likely to crack or shatter under high torque than standard bits, these are often used with power tools to install machine screws.

The knurled shank on these bits allows finger tightening. They can also be used with the included screwdriver.

A magnet holds the nut in place.

An opening at the tip accommodates the pin in the recess of tamper-resistant Torx screws. These are also known as pin-in-Torx bits.

Grip the indentations on the head of tri-groove fasteners.

A retaining ring grips inside the recess to hold screws in place. These bits have a ball end that allows angled entry to drive screws in hard-to-reach areas.

When you don't have exact alignment between the fastener and the tool, the ball end allows angled entry to turn screws in hard-to-reach areas.

The six rounded points fit the star-shaped recess of Torx-Plus screws. These bits have a similar profile to Torx but are not recommended for use with standard Torx screws.

Also known as Bristol bits, these have a knurled-end shank that allows finger tightening. They can also be used with the included screwdriver.

Keep bits from slipping. Insert a bit into the adapter, place a screw on the end of the bit, and slide the adapter sleeve over the screw. The sleeve retracts as the screw is driven. These adapters hold hex-shank bits (also known as insert bits) in powered tools.

Bend these adapters up to 90° to access hard-to-reach fasteners. Use them to hold hex-shank bits (also known as insert bits) in powered tools.

A magnetic ring at the end of the adapter holds flat-head screws in place to ensure good contact between the bit and screw. Use these adapters to hold hex-shank bits (also known as insert bits) in powered tools.

Lock your bit into the adapter to prevent accidental disengagement. These adapters attach to square-drive tools.

Attach these adapters to square-drive tools.

Insert these adapters into your SDS-drive rotary hammer to use it with hex-shank bits (also known as insert bits).

Mount the magnetic base to walls, cabinets, and other steel surfaces.

Keep these caddies in your tool drawer or take them with you.

These assorted shafts attach to a handle or can be used with socket wrenches and power tools. They have a ball end that allows angled entry to make good contact with the recess when a standard-tip shaft can’t.

Extra-long bits allow access to hard-to-reach fasteners.

Extra-long bits allow access to hard-to-reach fasteners.

These sockets are also known as pin-in-hex or pin-in-socket bits.

These sockets are made to withstand the high torque and force of impact tools.

The short bit on these sockets fits in spaces where height clearance is limited.

The ball end allows angled entry when you don't have exact alignment between the socket bit and fastener.

These sockets are also known as pin-in-hex or pin-in-socket bits.