95 Products

Use these NSF registered H1 lubricants in food-processing and preparation areas with a risk of incidental food contact. They form a nonstick film that won't attract contaminants, such as flour.

Lubricants with silicone can be used with plastic. Lubricants with PTFE have small particles of PTFE that fill in surface imperfections for excellent lubricity.

A high load-carrying capacity makes these lubricants good for use on chain and moving metal parts. They dry to form a film that lubricates without attracting dust.

Lubricants with graphite have good heat and excellent wear resistance. Lubricants with PTFE can be used with most plastics and are chemically inert.

Made of graphite, these powders and flakes lubricate under heavy loads and high temperatures. They resist most chemicals and conduct heat and electricity.

Powder lubricants get into hard-to-reach spots, such as locking mechanisms and fastener threads, better than flakes. Lubricant in a can and drum can be used dry or mixed with oil and grease to increase their load-carrying capacity or improve their ability to conduct heat and electricity. Lubricant in a tube can be used dry. It has a precision-tip applicator.

Flake lubricants conduct heat and electricity better than powder. Use them dry or mix with oil and grease to increase their load-carrying capacity or improve their ability to conduct heat and electricity.

Reduce mess and waste with these easy-to-apply, nonstaining lubricants. They reduce friction between your cutting tool and workpiece to make cutting cycles faster and easier, improve surface finishes, and extend tool life. All resist running and dripping. They are chlorine free, for use where chlorine waste disposal is a concern, and sulfur free.

Lubricants in a stick are solid and can be applied to cutting surfaces, such as band saw blades and drills bits. Lubricants in a tube dispense as a paste and are good for vertical applications.

Lubricants with graphite are for high-heat applications. Apply to hot surfaces (400° to 850° F), and they melt to coat the surface evenly.

Lubricants that cannot be sold to the regions listed are restricted by product labeling requirements.

These easy-to-apply stick lubricants won't drip or run for a cleaner workspace. Use them for tapping many types of metal, as well as plastic and rubber. Apply to taps to make cutting faster and easier, improve surface finishes, and extend tool life. They are chlorine free, for use where chlorine waste disposal is a concern, and sulfur free.

Corrosion-resistant additives allow these lubricants to withstand caustic environments, such as steel mills and power plants. Also known as thread lubricants, antiseize lubricants prevent threaded fasteners and close-fitting parts from locking together due to corrosion, contamination, or heat.

Lubricants with aluminum and with copper have good heat resistance. Lubricants with graphite have good chemical and corrosion resistance, along with excellent heat resistance. Loctite® Silver Grade Anti-Seize can be used with fine threads. Lubricants in a stick won’t run or drip.

Copper allows these lubricants to conduct electricity, while graphite gives them good chemical and corrosion resistance. Also known as thread lubricants, antiseize lubricants prevent threaded fasteners and close-fitting parts from locking together due to corrosion, contamination, or heat.

Loctite® C5-A Copper-Based Anti-Seize lubricants can be used with salt water and petroleum-based chemicals. LB 8065 comes as a stick for no-mess application.

Dielectric strength measures the maximum voltage a lubricant can withstand without losing its insulating properties. The higher the dielectric strength, the better its quality as an insulator.

Electrical resistivity is a measure of how well a material opposes the flow of electricity. The lower the rating, the more electricity it conducts.

These lubricants dry to form a thin, solvent-resistant film that won't squeeze out or attract dirt. They're made with moly to withstand heavy loads and pressure. They can handle low-speed loads at temperatures up to 745° F and static loads up to 2400° F. Also known as thread lubricants, antiseize lubricants prevent threaded fasteners and close-fitting parts from locking together due to corrosion, contamination, or heat.

Loctite® LB 8017 Moly Dry Film can also be used with chain and other moving metal parts.

Certificates with a traceable lot number and product shelf life are available for these products. Download certificates from ACTIVITY after your order ships.