For a more secure connection than rail- and adhesive-mount clamps, weld the bottom plate of these clamps onto your rails. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.

For use with a single line, these clamps mount directly onto rails, no adhesive or welding required. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.

Bolt or weld these rails to the mounting surface, then attach clamps with a rail nut.

For use with a single line, these clamps brace pipe, tubing, and conduit directly against the mounting surface.

For use with a single line, these plastic clamps reduce wear on softer materials, such as tubing and cable, and prevent corrosion caused by metal-to-metal contact.

Route two lines of tubing with a single clamp. Commonly used in compressed air systems, these polypropylene clamps withstand moisture and most chemicals. They have a folding arm that closes to secure material.

Quickly mount parallel lines of pipe, hose, or tubing by clicking them into these clamps. Made of acetal, they are UV-resistant and can be used outdoors.

Join these clamps together to line up multiple pipes, cables, or tubes side-by-side, even when they are different sizes.

A cushion covering the clamp reduces vibration and wear from clamp edges. Clamps surround lines of pipe, tubing, and conduit completely while holding them close to the mounting surface.

A molded cushion reduces vibration and wear from clamp edges, plus it provides a tighter fit around material than standard vibration-damping loop clamps.

Tighten the bolt for an exact fit around material. Clamps secure vertical pipes in sanitation drain applications and prevent them from coming in contact with the mounting surface.

Mount these general purpose U-bolts into an existing bracket, or combine with a mounting plate for a secure hold at the mounting surface.

A mounting plate provides a more secure hold at the mounting surface.

Reduce vibration and noise in your lines—a plastic cushion tightly grips pipe, tubing, and conduit to prevent movement. Nylon-insert locknuts grip the thread to resist loosening.

A durable rubber cushion and mounting plate prevent corrosion and wear caused by metal-to-metal contact. The mounting plate is removable, so the U-bolts can be installed onto an existing line without needing to dissemble it.

Also known as conduit hangers, these hangers load from the bottom so you can add or remove material without removing the mounted hanger.

Mount these hangers on top of one another to organize multiple lines of pipe, tubing, and conduit at any angle.

Rubber cushions fit material tightly to reduce vibration and provide a more secure hold than loop hangers. The cushions also protect material from sharp edges and prevent corrosion caused by metal-to-metal contact.

These hangers fit a range of material sizes. Push them closed to lock at the size you need. They provide a more secure hold on material than loop hangers.

Clip these hangers onto the side of threaded rod. Unlike other threaded-rod-mount hangers, you can use more than one hanger on the same rod to organize multiple lines of pipe, tubing, and conduit.

These hangers have a swivel nut for adjusting direction after mounting. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.

Use these hangers in corrosive environments and where chemicals are present. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.

Route multiple lines of pipe, tubing, and conduit with a single hanger. A wide opening and locking tab allow access for installation, adjustment, and removal.

Cut as much strap as you need to hang duct, pipe, and other materials.

Mount these beams across parallel roof joists to hang threaded rod and route pipe, duct, and other overhead systems in areas where there’s no anchoring point.

Reduce noise caused by HVAC systems. These sturdy rubber supports isolate vibration caused by heat pumps and air conditioning units, resulting in a quieter facility. When used on roofs, they also keep components above puddled water, which can cause damage.

For a secure hold on pipe and conduit suspended above the ground, these supports have a cushioned clamp provides a 360° grip while reducing vibration.

Create custom-length cable ties for large bundles and heavy materials.

Rails are drilled with consistently spaced holes for multiple mounting options that do not require machining. Use this steel bolt-together framing to build guards, tables, and racks.

Use this metal strapping for securing pipe coverings as well as for packaging.