The switch activates on increasing pressure caused by rising water levels for a long service life. It has a separate cord, so you can replace the switch without replacing the whole pump. Use the handle to carry pumps from job to job.

Move higher volumes of water than with other high-flow water-removal pumps. These pumps activate when plugged in. You can add a plug-in switch to control when the pump activates.

Clean up water in flooded areas without a sump pit. Pumps activate when plugged in. You can add a plug-in switch to control when the pump activates.

Also known as bilge pumps, these remove fresh and salt water from spots where other pumps don’t fit.

This pump has a totally enclosed nonventilated (TENV) motor that is cooled by the liquid being pumped. Also known as a flexible impeller pump, it creates a suction force that can draw liquid upward to fill the pump chamber when your liquid source is below the pump.

These pumps provide about 25% more flow than standard float-switch activated pumps for sewage water. Equipped with a large intake and rugged impeller, they transfer raw sewage water with solids up to 2” in diameter. The float switch is wired to the pump.

These pumps have a heavy duty motor with sealed bearings that generates a flow rate similar to our other sump pumps for sewage water while using fewer amps. Use them to transfer raw sewage water with solids up to 2” in diameter. The float switch is wired to the pump.

The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump.

Equipped with a large intake and a rugged impeller, these pumps transfer raw sewage water with solids up to 2” in diameter. The float switch is wired to the pump.

The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump. Equipped with a large intake and rugged impeller, these pumps transfer raw sewage water with solids up to 2” in diameter.

Pumps have a cast iron housing that stands up to demanding environments. The float switch is wired to the pump. Use with debris-free water.

These pumps activate when plugged in. You can add a plug-in switch to control when the pump activates. Use with debris-free water.

Convenient for applications where a sump pit is impractical, these pumps include a basin. Use with debris-free water.

Since the motor is totally enclosed fan cooled (TEFC) and never comes into contact with the water, these pumps can be used with hot water up to 200° F.

Move higher volumes of water with solids than other sump pumps. The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump. Also known as effluent pumps, they accommodate solids up to 3/4” in diameter. They are often used with liquid waste that has passed through a septic tank, so most solids are removed.

Use these pumps at temperatures up to 200° F. Also known as effluent pumps, they accommodate solids up to 3/4” in diameter. They’re often used with liquid waste that has passed through a septic tank, so most solids are removed. The float switch is adjustable and wired to the discharge pipe.

The float switch has a separate cord that can unplug, so you can repair the switch without replacing the whole pump. Also known as effluent pumps, these accommodate solids up to 3/4" in diameter. They're often used with liquid waste that has passed through a septic tank, so most solids are removed.

Rated for continuous use, these pumps are often used to move caustics such as antifreeze and salt water. Mount them in any position, even upside down. Also known as diaphragm pumps, they are typically used for low-flow spraying, draining, and washdown applications.

Commonly called rotary vane pumps, these are designed to pump water at high pressures in low-flow applications. Use at pressures up to 240 psi.

An aluminum enclosure around the motor provides protection in dusty and dirty environments. Designed to fit into small equipment, these pumps have miniature gears and a subfractional horsepower motor for low-flow applications.

A detachable motor assembly allows you to leave these pumps inline while servicing or repairing the motor. Install these pumps directly in your pipeline for applications such as hot-water circulation and hydronic heating and cooling.

Eliminate seal wear and leakage—these pumps have magnets that turn the impeller for a long service life. Install them directly in your pipeline for applications such as hot-water circulation and hydronic heating and cooling.

These pumps have higher flow rate than other inline circulation pumps and are cooled by the liquid being pumped to extend the life of the motor. Install them directly in your pipeline for applications such as hot-water circulation and solar heating.

A powerful motor provides twice the flow rate of other self-priming circulation pumps. It is totally enclosed fan-cooled (TEFC) for use in dusty, dirty, and damp environments. Install these pumps up to 20 ft. above your liquid source to drain underground tanks and process wastewater.

A sealless construction means these pumps have few moving parts that can fail and shorten service life. The intake can be completely submerged in liquid.

Drain underground tanks and process wastewater with pumps that can be installed up to 20 ft. above your liquid source.

The durable motor and impeller can handle dirty coolant and machine lubricants with solids up to 1/4" diameter. These pumps have an intake that can be completely submerged in liquid.

Move water and coolants, such as ethylene glycol, in boiler feed systems, cooling towers, and heat exchangers.

These pumps can be used to move water and lubricating oil in boiler feed systems, cooling towers, and heat exchangers.

Propel liquid higher and farther than standard circulation pumps. They're commonly used with chillers, heat exchangers, and boiler feed systems.

A powerful motor provides twice the flow rate of other extended-life circulation pumps. The motor is totally enclosed fan-cooled (TEFC) for use in dusty, dirty, and damp environments. Magnets turn the impeller to eliminate seal wear and leakage for a long service life. These pumps are often used with electroplating and photographic solutions.

These pumps have a totally enclosed fan-cooled (TEFC) motor for use in dusty, dirty, and damp environments. The impeller is turned with magnets to eliminate seal wear and leakage for a long service life.

A 316 stainless steel housing sealed with fluoroelastomer resists mild chemicals and acids, such as coolant, oil, and phosphoric acid.

For accurate dispensing in extremely low-flow applications, these pumps allow you to adjust flow in 2% increments.

Drain and transfer liquid more quickly and easily than hand-operated pumps and siphon pumps.

Including nozzles and connectors, these pumps come with everything you need to start pumping.

Protected from impact by a durable epoxy-coated aluminum housing, these pumps can be submerged or connected remotely to a pipe in your line. Use to circulate water in small tanks, cooling baths, fountains, and other low-flow applications.

These pumps can be submerged or connected remotely to a pipe in your line. Use them to circulate water in small tanks, cooling baths, fountains, and other low-flow applications.

These pumps can be submerged or connected remotely to a pipe in your line. Magnets turn the impeller so there's no shaft seal to wear out. Use to circulate water in small tanks, cooling baths, fountains, and other low-flow applications.

Circulate salt water in submerged and open-air applications.

Fully submersible, these pumps are designed for installation inside your condensate collection tank or drain pan. Use them to collect and remove condensate from air conditioners, refrigerators, dehumidifiers, and other equipment.

To handle high condensate volume, the workload is distributed between two pumps for a longer service life than standard high-flow steam condensate pumps. These pumps move a higher volume of condensate than standard steam condensate pumps. Use them in low-pressure steam systems to capture hot condensate and return it to your boiler or feed unit.

To handle high condensate volume, the workload is distributed between two pumps for a longer service life than standard steam condensate pumps. Use in low-pressure steam systems to capture hot condensate and return it to your boiler or feed unit.

Designed for use in low-pressure steam systems, these pumps capture steam in the attached tank and return hot condensate to your boiler or feed unit.