Also known as a geophone clip, this clip has rounded jaws that clamp onto battery terminal lugs and other curved surfaces for hands-free testing.

Hook up electrical testing equipment and create test circuits.

Mount parallel lines of pipe, tubing, or conduit directly against the mounting surface.

Even when these clamps are installed side by side, the clamping screws remain accessible. Use them to route pipe, tubing, and conduit across strut channel.

Secure insulated pipe to strut channel without pinching the insulation or exposing the pipe. These clamps are sized for use with insulated pipe and have a plastic insert that creates a seal around the insulation to prevent the pipe from sweating, which can cause mold and corrosion.

For use with a single line, these plastic clamps reduce wear on softer materials, such as tubing and cable, and prevent corrosion caused by metal-to-metal contact.

A rubber cushion reduces vibration and wear from clamp edges. The cushion also protects lines of pipe, tubing, and conduit from corrosion caused by metal-to-metal contact.

Secure two pressurized hydraulic lines with a single clamp to lessen vibration in hydraulic systems. Weld the bottom plate onto the mounting surface for a more secure connection than rail- and adhesive-mount clamps.

Quickly mount parallel lines of pipe, hose, or tubing by clicking them into these clamps. Made of acetal, they are UV-resistant and can be used outdoors.

For use on a single line, these polypropylene clamps withstand moisture and most chemicals. They're commonly used to route tubing in compressed air systems. A folding arm closes to secure material.

Route two lines of tubing with a single clamp. Commonly used in compressed air systems, these polypropylene clamps withstand moisture and most chemicals. They have a folding arm that closes to secure material.

Slide these clamps into strut channel and snap closed for quick installation with no tools required. They are noncorrosive, nonconductive nylon.

Join these clamps together to line up multiple pipes, cables, or tubes side-by-side, even when they are different sizes.

Customize these clamps to any object—they have a bend-and-stay design so you can mold them to the size and shape you need. Made of plastic-coated 316 stainless steel, they withstand abrasion, corrosion, and UV rays.

Lock your line in faster than any other hanger. These hangers automatically close when you press your line into the clamp.

Suspend material at any angle from the beam. Clamps have a fixed jaw that secures to the beam and a hanger that swivels 360° to position material and accommodate for misalignment.

Attach these supports onto metal stud knockouts to route cable, conduit, and tubing through metal studs.

For a secure hold on pipe and conduit suspended above the ground, these supports have a cushioned clamp provides a 360° grip while reducing vibration.

Bolt directly to a pipe flange to suspend a run of pipe above the ground.

Reduce noise caused by HVAC systems. These sturdy rubber supports isolate vibration caused by heat pumps and air conditioning units, resulting in a quieter facility. When used on roofs, they also keep components above puddled water, which can cause damage.

These U-shaped supports allows access to pipe and conduit after installation.

Connect bare-copper ground wire to grounding rods.

Attach grounding wire to pipes.

Straps fit around pipes and grounding rods.

Connect grounding wires to steel structures, fence posts, and transformers.

Connect these clamps to a wide range of wire sizes.

Made of lead, these clamps resist corrosion to stand up to marine environments. Use a lug to attach your cable to the stud.

Connect these lugs to cable with a crimping tool or by soldering.

Serrations on both sides lock these lugs in place.

When heat is applied, the flux and solder mixture creates a metallic bond that is nearly twice as strong as crimping or compression connections.

An offset tongue gives you extra space to insert wire.

Splice large size wires without special tools—insert your wires and tighten the hex nut to make a connection.

These cables are for occasional use on cars and other small transport vehicles.

Including a robot tool mount and electrical connectors, these grippers come ready to attach to robot arms with standard ISO 50 mounting hole patterns. Good for areas without compressed air, they use electricity to pick and place items in packaging, assembly, and machine-tending applications.