Built to handle tough, repetitive-use applications, these are more durable than standard straight-blade connectors.

Create a streamlined appearance—the flat face lies flush with your wall plate.

Access the wire connection by opening the hinged housing. These connectors have screw terminals to create a secure connection; wire must be stripped before winding around the screw terminal.

Visually confirm that connectors have power; they have an indicating light that is visible from any angle.

Add a fuse to protect equipment from current overload.

Suitable for use outdoors, receptacles can be used in wet and damp environments. They keep personnel safe from electric shock by adding ground fault protection.

Minimize the risk of electric shock and electrical fires with a single receptacle.

Reduce the likelihood of an electrical fire. Receptacles interrupt power when an electric arc is detected.

Charge mobile devices without an adapter.

An indicating light that is visible from any angle lets you know when these plugs have power. They have an extra-tight fit when mated with a receptacle to withstand high vibration. Also known as hospital grade plugs.

Eliminate the need for wire stripping; snap-on terminals pierce the wire insulation. When mated with a receptacle, these plugs have an extra-tight fit to withstand high vibration. Also known as hospital grade plugs.

Keep personnel safe from electric shock by adding ground fault protection. These receptacles have an extra-tight fit when mated with plugs to withstand high vibration. Also known as hospital grade receptacles.

Visually confirm that sockets have power—the face lights up when they're connected. The rubber housing protects them from damage caused by drops and other impact.

Stainless steel hardware and nickel-plated blades or slots protect connections from damage in corrosive environments.

Use connectors where ignitable gas and dust may be present. They are UL listed for Class I, Division 1 and 2, Groups C and D; Class II, Division 1 and 2, Groups F and G; and Class III hazardous environments.

Prevent damage to electronic equipment caused by spikes in current. Mount these receptacles to DIN rail.

Attach these general purpose receptacles to DIN rail to bring power closer to where you need it.

Also known as twist-lock devices, these connectors withstand tough, repetitive use, and are more durable than standard turn-lock connectors. They turn to lock together when mated to prevent accidental disconnection.

Check the status of a ground connection—a green light signals that connectors have power and are safely grounded. They turn to lock together when mated to prevent accidental disconnection.

When mated, these connectors meet NEMA 6P for protection against washdowns and temporary submersion.

Rated NEMA 6P, NEMA 13, IP66, and IP69K when mated, these connectors withstand high-pressure, high-temperature washdowns, oil/coolant splashing, and are corrosion-resistant so they can be used in high-vibration marine environments.

A rubber housing protects these connectors from damage caused by drops and impact. They turn to lock together when mated to prevent accidental disconnection.

A quarter turn locks these connectors in an outlet to remain secure in high-vibration applications and prevent accidental disconnection. They are not compatible with NEMA configurations.

Connect and disconnect with the power on—spring-loaded contacts open like a switch when separating the connectors, preventing an electrical arc.

These connectors meet international standards IEC 309-1 and 309-2. They prevent an electrical arc when separating mated connectors, so you can safely connect and disconnect with the power on.

Use connectors where ignitable gas and dust may be present, such as in refineries and silos. They also prevent an electrical arc when separating mated connectors so you can safetly connect and disconnect with the power on.

Join two connectors that both have internal threads.

These connectors are often used with 18 mm and 30 mm proximity switches and limit switches.

Join two connectors that both have internal threads.

Quickly mate these connectors by pushing them together. They're often used with 12 mm proximity switches and valves in automated systems.

These connectors withstand corrosion and abrasion. Screw them together for a secure connection. They're often used with 12 mm proximity switches, valves, and power supply units.

Safely use these connectors with 12 mm proximity switches, console lights, valves, and power supplies in food, beverage, and pharmaceutical applications—they’re FDA compliant for direct food contact.

Plug these connectors into hazardous location devices. Using a NAMUR signal, they operate at a low current and voltage, so they prevent the risk of sparks and ignition in volatile areas.

Rated IP69K, these M16 connectors protect against dust, debris, and hot, high-pressure jets of water at high volumes.

Push these connectors together to quickly create signal and data connections in tight spaces. All are smaller than M5 and M8 connectors. They also need less space to mate than screw-together connectors, which require two hands to twist them in place.

Some of the smallest signal/power connectors we offer, these connectors fit in tight spaces and are often used in electronics.

Configure a connector for your application—combine inserts for power and signal with a base and a hood.

Carry up to four times the current of standard Compact Latching Connectors. The base and hood latch together securely, yet can be quickly detached for equipment repair or replacement.

A rubber seal and stainless steel hardware give these connectors excellent chemical resistance. They're rated NEMA 12, 4X, and IP65 for protection against corrosion, oil, and washdown environments.

Use these connectors in oily and washdown environments; they're rated NEMA 4X and 12. The base and hood latch together securely, yet can be quickly detached for equipment repair or replacement.

Protect Mil. Spec. connectors when not in use.

These connectors meet MIL-DTL-26482, so they're compatible with other products that meet the same standard. Quickly mate by pushing them together.

Configure a connector for your application—combine housings with pins and sleeves for different wire sizes. Use them with standard Molex connectors.

Configure a connector for your application—combine housings with pins and sleeves for different wire sizes. They fit AMP MATE-N-LOK connectors.

Stack as many connectors on top of each other as needed—the housings clamp together to form a secure attachment.

Each set includes one plug and one socket. These connectors withstand moisture, harsh engine fluids, and high temperatures. Also known as weather-pack connectors.

Install these connectors in panels, enclosures, and bulkheads to join equipment with compatible Deutsch-style DC connectors.

Power robotic arms and other high-amperage machines in motor controls, conveyors, and sorting and packaging systems from your main M35 power line.

Protect high-current connectors when not in use.

Use these sockets with Allen-Bradley servomotor systems.

Connectors lock into place for a secure connection in high-vibration environments. They power small devices, such as chargers for electronics, from a vehicle. Also known as cigarette-lighter plugs and sockets.

Mount these terminals on a threaded screw or stud for a more secure connection than spade and hook terminals.

Mount these elongated ring terminals on a range of screw sizes.

When heat is applied, the insulation shrinks and creates a seal that keeps out water, salt, and contaminants.

A plastic cover on the barrel provides electrical insulation. These terminals can withstand temperatures up to 300°F.

A serrated edge on the inside of the ring grips the mounting screw for a secure hold.

A plastic cover on the barrel provides electrical insulation rated to 600 volts.

Save preparation time—these cords are ready-to-use with ring terminals on each end of a single-conductor wire.

A plastic cover on the barrel provides electrical insulation.

Heat these terminals to shrink the insulation, creating a seal that keeps out water, salt, and contaminants.

Easy to install, connect, and disconnect, yet difficult to shake loose. These terminals interlock with each other to make a secure connection.

The connection tab on these terminals is completely covered with insulation, leaving no metal exposed when mated.

Rated UL 94 V-0 for flame resistance, these terminals are made of flame-retardant, self-extinguishing material to reduce the risk of fire.