With a slimmer profile than other strip machine lights, these lights fit in tight spots inside machinery because they don’t have a circuit board.

Illuminate machines or monitor processes in environments that reach up to 210° F. These lights have a thick housing that acts as a heat sink to protect the LEDs and driver from overheating.

Illuminate machines or monitor processes in areas where flammable or combustible gases may be present, such as during leaks or ventilation failures. These lights are rated for use in NEC Class 1, Division 2 hazardous locations.

With a smooth, shatterproof lens, these lights have no crevices where debris can accumulate. Their stainless steel connectors, plastic lens, and mounts resist acids, alkalis, and other chemicals commonly used in food environment washdowns.

Know your machine’s status at a glance—green for running, red for stopped, yellow for standby. Using your programmable logic controller (PLC), you can adjust the brightness of these lights and mix red, green, and blue light to achieve thousands of colors.

Brighten countertops that your ceiling lights can’t reach. These lights are low-profile, so they won’t take up valuable workspace below your cabinets.

A motion sensor turns on these lights when an enclosure door is opened. Mount them inside cabinets, closets, and other enclosed spaces.

Illuminate your electronics cabinets and racks with long-lasting LED lights.

A flexible design allows these lights to be suspended above, wrapped around, or routed through areas on the job site.

Light up large, open rooms where you need a quick setup and takedown, such as a room under construction. Just hang these lights from a ceiling up to 30' high and they’re ready to go.

A series of bulb heads are attached to a power cord to provide overhead lighting for job sites.

Hang these lights above your workspace—they shine through long tubes to distribute even light with minimal glare and shadows. Carry them where you need them and suspend them from pipes, beams, and other overhead surfaces.

Hang these lights where you need them on the job site.

Power these lights with the same battery as your other cordless tools. They run on a Milwaukee M18 battery to light up work where there’s no outlet.

Because these lights are compatible with DeWalt rechargeable batteries, you can keep one type of cordless tool battery on hand. Their head pivots to aim light where it's needed in areas that don't have electrical power service.

Point light where it’s needed—even in wet areas. These lights are sealed against splashing and dripping water.

Aim light where you need it—even in explosion-prone spaces—by raising, lowering, and tilting these lights on their tripod. Rated NEC Classes I, II, III, and Zone 0, they’re safe to use near ignitable concentrations of flammable or combustible gas, dust, or fibers.

Bring light to explosion-prone work areas. Rated NEC Class I, these lights are safe to use in areas with ignitable concentrations of flammable or combustible gases, vapors, and liquids.

Compact and easy to carry, these ETL listed lights stand up to dripping, splashing, and falling liquids. The head adjusts up and down to direct light where it's needed.

Bring light to remote areas with the DeWalt rechargeable battery that's already in your toolkit.

Flood dark, remote jobsites with multiple tiers of light. These cordless lights stack on top of each other to focus a strong beam of light in one direction.

Bring light to remote, wet areas. These floodlights are IP rated to handle humidity and dripping, splashing, and falling liquids. Adjust their tripod up and down to direct light as far as you need.

Brighten areas of a jobsite with these floodlights, and move them at a moment’s notice.

As bright as stadium lights, these floodlights are the most powerful in our offering—they’ll brighten jobsites half the size of a football field. They run on a diesel generator you can use to power other lights and tools in the field.

Light up drawers and enclosures where power isn’t available—these lights are compact and powered by battery.

The articulating arm on these lights holds its position better than gooseneck-arm lights, especially around vibration.

Pivot the head to cast a narrow beam of light to exactly where it's needed.