These solenoid valves operate on electricity to automatically start and stop flow. The actuator is directly mounted to the valve body to minimize movement and reduce wear.

Lower profile and available in smaller connection sizes than standard valves, these fit in tight spots.

Insert tubing into the fittings on these valves—no heat, solder, or flux required.

Less than half the size of our other compact valves, these have small pipe connections for miniature lines.

To fit in tight spots, these valves have a slimmer body than standard valves with an exhaust port.

Turn the knob to adjust how much these valves will open or close when actuated. They are often used in irrigation and landscaping applications.

Use with coolant and detergent such as ethylene glycol or soap solutions.

To change the flow rate of antifreeze and cleaning solutions, use the adjustment screw or knob to manually set how much these valves will open when actuated.

Reduce your pipeline footprint with these low-profile valves that are about half the size of standard valves for coolant.

Designed to withstand the high temperatures and pressures in steam service applications.

Insert tubing into the fittings on these valves—no heat, solder, or flux required.

For applications sensitive to contamination, these valves stop flow without contacting the process media by pressing down on the outside of tubing.

Often used to control single-acting, spring-return air cylinders, these valves have a third threaded port to exhaust media.

Supply fuel oil to boilers, furnaces, and other equipment.

Maintain and repair these valves without unthreading pipe connections. They have a three-piece bolted body that disassembles inline for access to internal components.

With a slimmer motor than other motor-driven valves, these fit in tight spots.

Also known as butterfly valves.

Slide copper pipe into the solder-connect fittings on these valves and weld for a strong, permanent connection.

All valves have threaded NPT connections.

For food and beverage systems that require frequent cleaning, these valves have polished internal surfaces and sanitary quick-clamp connections for easy disassembly.

Repair actuated on/off valves from Asco, Burkert, Granzow, and Parker with these kits that include replacement seals, plunger assemblies, and springs.

These valves operate on electricity to automatically divert flow between ports. Use with water, oil, air, and inert gas.

Often used for emission analysis and gas processing, these valves attach to each other horizontally to create one centralized manifold for servicing multiple process lines. All are rated for use with water, oil, air, and inert gas. They operate on electricity to automatically divert flow between ports.

These valves create one action, such as extending a cylinder. Apply voltage to the electrical connection to actuate. They're also known as 3/2 valves.

Also known as 3/3 valves, these valves close all ports in the off position to stop equipment in a locked position with air pressure holding it in place. They're often used for vacuum suction and release applications and intermediate cylinder stops.

Run through equipment cycles up to 30% faster than with standard valves. These valves shift between flow positions in 1.7 ms. Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port.

In the off position, these valves exhaust all air pressure, allowing the equipment to return to the neutral position. Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Apply voltage to the electrical connection to actuate.

Create two actions at the same time, such as extending two single-acting cylinders at once. Apply voltage to the electrical connection to actuate. Also known as pressure center valves.

Use a single valve to create motion and control the speed of that motion.

With two 3-way integrated solenoid valves, these electrically controlled valves direct airflow to end-of-arm tools that don’t require vacuum suction, such as pick-and-place grippers. Also known as 3/2 valves, each of the two solenoid valves directs air to a different port.

Mix and match valve styles on one manifold to meet your control needs. Mount multiple valves to a manifold to reduce piping requirements and create multiple actions from a single pressure input.

Also known as solenoid valves, these valves are operated by an electrical signal to turn airflow on or off.

Designed for use in dust-collection systems, these diaphragm valves periodically burst air to knock debris from filters.