In addition to stripping and cutting wire, this multifunction tool has screwdrivers, a wire bender, rulers, files, and a knife that swing out from the handle.

One squeeze strips insulation and pulls it off the wire.

This kit includes a wire stripper plus blades to strip electrical wire and coaxial cable.

Because you load wire from the front of this stripper, it’s useful in tight spaces.

Use the adjustable stop to precisely set the strip length.

The rubber handle on this knife provides a more secure and comfortable grip than plastic handle knives.

The blade on these strippers swivels so you can make end and center strips.

One squeeze strips outer and inner insulation and pulls it off Romex and other types of flat cable.

The ratchet applies the correct pressure to ensure a complete crimp every time on pin-and-sleeve contacts.

The rubber grip provides protection up to 1,000 volts AC.

Dies snap in and out of this tool, so you can quickly change from crimping one electrical connector type to another.

The ratchet applies the correct pressure to ensure a complete crimp every time.

Because you insert the wire ferrule from the front, this tool is useful in tight spaces.

The rubber grip provides protection up to 1,000 volts AC.

Insert pin-and-sleeve contacts into connectors.

Extract pin-and-sleeve contacts from connectors.

Strip fiber-optic cables without scratching or damaging them. These cable strippers have three nonmarring openings to handle different thicknesses of fiber-optic cable jackets and buffer coatings.

This tool turns like a screwdriver to strip a short coaxial cable in a tight space.

Strip both Ethernet and coaxial cable.

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet EN 60900 and IEC 60900.

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC, EN, or ASTM standards.

The assorted drivers in these sets have an insulated handle and shaft that protect against shock from accidental contact with live electrical circuits. They are tested to 1,000 volts to meet ASTM and IEC standards.

The assorted keys in these sets have an insulated handle and shaft that protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC 60900 and ASTM F1505-01. They have a long shaft that reaches into tight spots to turn fasteners.

The assorted drivers in these sets have an insulated handle and shaft that protect against shock from accidental contact with live electrical circuits. They are tested to 1,000 volts to meet IEC, EN, or ASTM standards. Use the rotating end cap on the handle to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

Also known as ESD-safe screwdrivers, the handle drains static away from your application, preventing buildup from electrostatic discharge (ESD) that can damage sensitive equipment. Use the rotating end cap on the handle to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC 60900 standards. When set torque is reached, these drivers signal with an audible click.

Additional features, such as wire terminal crimpers, enable you to perform a variety of electrical wiring and installation work with a single tool. Also known as lineman’s pliers, use them to pull, bend, and cut wire.

When there isn't clearance to use standard-grip pliers, the angled head on these tools gives you access. Also known as lineman’s and combination pliers, use them to pull, bend, and cut wire.

Deep serrations provide the firm grip necessary for pulling rebar tie wire, and the hook-shaped handle end keeps your hand from slipping off. Also known ironworkers’ pliers, these tools also bend and cut wire.

Avoid the potential for an arc flash or short circuit that can occur when using conventional insulated tools with metal components. Completely metal-free, these pliers are plastic with ceramic cutting blades. They are tested to 1,000 volts to meet IEC 60900 and ASTM F1505. Use to pull, bend, and cut wire.

Made of aluminum-bronze that is FM approved, these pliers satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present. Use them to pull, bend, and cut wire.

Insulated grips protect against accidental contact with live electrical circuits. These pliers are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Insulated grips protect against accidental contact with live electrical circuits. These pliers are tested to 1,000 volts to meet IEC 60900. Designed for looping and bending wire, they are also known as round-nose pliers.

Insulated grips protect against accidental contact with live electrical circuits. These pliers are tested to 1,000 volts to meet IEC 60900. They are shaped to reach around closely spaced components and other obstructions.

Protect against accidental contact with live electrical circuits. These plastic-insulated tweezers are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

An insulated handle protects against accidental contact with live electrical circuits. These picks are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Protect against accidental contact with live electrical circuits. These insulated retrievers are tested to 1,000 volts to meet IEC 60900 and ASTM F1505. The shaft bends and stays in position to reach objects in awkward spaces.

The single loop can handle up to six 10-ga. bare wires at once.

Safer to use around energized equipment than other types of fish tape, this fiberglass tape is also round, making it more flexible than flat and oval tape to pull wire through multiple bends.

Made of fiberglass with a plastic tip, this tape is safer to use around energized equipment than metal fish tape.

Use a blower or vacuum to insert this lightweight threading line into conduit or raceway, and attach it to your pulling rope to guide the rope.

Each set includes six grips for pulling one or more cables through conduit.

Insulated handles protect against shock from accidental contact with live electrical circuits. These scissors are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Also known as electricians' shears, the back edge of the blade has a file to clean contacts.

A guard protects your hands from hammer blows. These are also known as electrician's chisels.