Electronics Screwdrivers

Sets include an assortment of drivers with a rotating end cap on the handle that allows you to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

Replaceable-Tip Precise-Control
Screwdriver Sets

Sets include an assortment of drivers with a tip that can be replaced when it becomes worn. Press the rotating end cap on the handle with your palm to apply constant pressure to small fasteners while turning the body of the screwdriver with your fingertips.

Replaceable-Tip
Precise-Control Screwdrivers

The tip can be replaced when it becomes worn. These tools have a rotating end cap on the handle that allows you to apply constant pressure with your palm while turning the body of the driver with your fingertips.

Ball-End Precise-Control
Screwdriver Sets

The assorted drivers in these sets have a ball end that allows angled entry to turn screws in hard-to-reach areas. Use the rotating end cap on the handle to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

Ball-End Precise-Control Screwdrivers

When you don't have exact alignment between the fastener and the tool, the ball end allows angled entry to turn screws in hard-to-reach areas. Press the rotating end cap on the handle with your palm to apply constant pressure while turning the body of the screwdriver with your fingertips.

Screw-Holding
Precise-Control Screwdrivers

Push the handle's end cap to open the jaws at the tip; release to close around the screw. The end cap rotates, allowing you to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

Magnetic Screw-Holding
Precise-Control Screwdriver Sets

A magnetized tip holds the screw in place. Press the rotating end cap on the handle to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

Electrical-Insulating
Precise-Control Screwdrivers

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC, EN, or ASTM standards. Use the rotating end cap on the handle to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

Electrical-Insulating
Precise-Control Screwdriver Sets

The assorted drivers in these sets have an insulated handle and shaft that protect against shock from accidental contact with live electrical circuits. They are tested to 1,000 volts to meet IEC, EN, or ASTM standards. Use the rotating end cap on the handle to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

Static-Control Precise-Control
Screwdriver Sets

The handle on these assorted ESD-safe screwdrivers drains static away from your application, preventing buildup from electrostatic discharge (ESD) that can damage sensitive equipment. Press the rotating end cap on the handle to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

Static-Control
Precise-Control Screwdrivers

Also known as ESD-safe screwdrivers, the handle drains static away from your application, preventing buildup from electrostatic discharge (ESD) that can damage sensitive equipment. Use the rotating end cap on the handle to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

Ceramic Adjustment Screwdrivers

Use these ceramic-tipped screwdrivers for adjusting sensitive electronic components such as capacitors and resistors. They're completely nonconductive and nonmagnetic so there's no risk of short-circuiting or creating magnetic interference. Press the rotating end cap with your palm to apply constant pressure while turning the body of the screwdriver with your fingertips.

Precise-Control Bit Screwdrivers

Use these tools with 1/4" hex shank screwdriver bits. The rotating end cap on the handle allows you to apply constant pressure with your palm while turning the body of the driver with your fingertips.

Ceramic Changeable-Shaft
Adjustment Screwdriver Sets

Use these ceramic-tipped screwdrivers for adjusting sensitive electronic components such as capacitors and resistors. They're completely nonconductive and nonmagnetic so there's no risk of short-circuiting or creating magnetic interference. Remove and replace the shafts to use a different size or drive style.

Static-Control
Precise-Control Nutdrivers

Also known as ESD-safe nutdrivers, the handle drains static away from your application, preventing buildup from electrostatic discharge (ESD) that can damage sensitive equipment. Use the rotating end cap on the handle to apply constant pressure with your palm while turning the body of the driver with your fingertips.

Static-Control Precise-Control
Nutdriver Sets

The handle on these assorted ESD-safe nutdrivers drains static away from your application, preventing buildup from electrostatic discharge (ESD) that can damage sensitive equipment. Press the rotating end cap to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

Precise-Control Nutdrivers

Apply constant pressure to small hex nuts and cap screws. Press the rotating end cap on the handle with your palm while turning the body of the driver with your fingertips.

Precise-Control Nutdriver Sets

Sets include an assortment of drivers that allow you to apply constant pressure to small hex nuts and cap screws. Press the rotating end cap on the handle with your palm while turning the body of the driver with your fingertips.

Electrical-Insulating
Changeable-Shaft Screwdriver Sets

An insulated handle and shafts protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC 60900.

Electrical-Insulating Bit Screwdrivers

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet EN 60900 and IEC 60900.

Electrical-Insulating Screwdrivers

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC, EN, or ASTM standards.

Electrical-Insulating Screwdriver Sets

Sets include assorted drivers with an insulated handle and shaft that protect against shock from accidental contact with live electrical circuits. They are tested to 1,000 volts to meet IEC, EN, or ASTM standards.

Electrical-Insulating Nutdrivers

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet ASTM and IEC standards.

Electrical-Insulating Nutdriver Sets

Torque-Control Wing-Handle Keys

Often used to install carbide inserts in cutting tools, these keys have a small T-handle that prevents you from generating too much torque when turning a fastener.

Torque-Control
Wing-Handle Key Sets

The assorted keys in these sets have a small T-handle that prevents you from generating too much torque when turning a fastener. They are often used to install carbide inserts in cutting tools.

Screw-Holding Torque-Control
Wing-Handle Keys

A retaining ring on the tip grips inside the recess to hold screws in place. Often used to install carbide inserts in cutting tools, these keys have a small T-handle that prevents you from generating too much torque when turning a fastener.

Screw-Holding Torque-Control
Wing-Handle Key Sets

These assorted keys have a retaining ring on the tip that grips inside the recess to hold screws in place. Often used to install carbide inserts in cutting tools, these keys have a small T-handle that prevents you from generating too much torque when turning a fastener.

Electrical-Insulating
T-Handle Key Sets

The assorted keys in these sets have an insulated handle and shaft that protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC 60900 and ASTM F1505-01. They have a long shaft that reaches into tight spots to turn fasteners.

Electrical-Insulating T-Handle Keys

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC and ASTM standards. They have a long shaft that reaches into tight spots to turn fasteners.

Precise-Control Bit Assortments

The knurled shank on these bits allows finger tightening. They can also be used with the included screwdriver.

Torque-Control Flag-Handle Key Sets

The assorted keys in these sets have a small handle that prevents you from generating too much torque when turning a fastener. They are often used to install carbide inserts in cutting tools.

Torque-Control Flag-Handle Keys

Often used to install carbide inserts in cutting tools, these keys have a small handle that prevents you from generating too much torque when turning a fastener.

Electrical-Insulating Screw Starters

An insulated handle and body protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC 60900. They grip and turn screws that are too small to hold by hand or located in hard-to-reach spots.

Electrical-Insulating
Torque Screwdrivers

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC 60900 standards. When set torque is reached, these drivers signal with an audible click.

Screwdriver and Nutdriver Sets

Static-Control Changeable-Shaft
Screwdriver and Nutdriver Sets

The handle drains static away from your application, preventing buildup from electrostatic discharge (ESD) that can damage sensitive equipment. Also known as ESD-safe screwdrivers and nutdrivers.

Changeable-Shaft Precise-Control
Screwdriver and Nutdriver Sets

Slide a different shaft into one of three handles to change tip size or drive style.

Precise-Control Screwdriver
and Nutdriver Sets

Also known as jewelers' screwdrivers.